冲击压实后旧水泥混凝土路面作为垫层及其回弹模量的试验研究

在提出冲击压实后旧水泥混凝土路面作为加铺结构层之一的设计思路的基础上，阐述实测回弹模量的重要性；通过对大量实测承载板数据进行分析，获得了实施冲击压实处理后旧水泥混凝土板及板下基层回弹模量的量值范围和变化规律，作为加铺层设计的计算参数，并用来评价其残余承载能力。     

某高速公路13m跨简支桥检测试验研究

采用原位等效静荷载试验方法,检测和验证13m跨简支钢筋混凝土单块板,铰缝处理前后结构的受力性能,铰缝处理前后单板挠度分别为1/307、1/786,单板经铰缝处理满足了正常使用要求。     

旧水泥混凝土路面FWD实测数据的分析

基于某国道的FWD实测数据,分析FWD参数与旧水泥混凝土路面状况(现场调查实录及测试数据)间的某些相关性,探索旧水泥混凝土板的接缝传荷能力、弯曲刚度、综合承载能力等定性或定量的判别方法,提出利用FWD加载中心弯沉值总水平评价旧水泥混凝土路面综合承载能力的设想。     

舱口盖强度计算方法

在某集装箱舱口盖结构强度的有限元计算中，对舱口盖周围水平限位器和支撑块处的约束以及顶部压紧器处的关联程度进行了模拟，分别讨论了在垂向设计载荷的情况下，水平限位器、支撑块处的不同约束以及顶部压紧器的不同关联程度对舱口盖应力分布的影响，得出更符合实际情况的舱口盖结构强度计算方法。     

基于Ansys的矩形加筋平盖封头强度评定

将有限元方法与分析设计相结合,利用有限元分析软件Ansys对一种矩形加筋平盖封头进行强度评定。本文首先介绍瓶盖封头结构的改进。然后建立有限元模型,并进行应力求解。结果表明,此加筋平盖封头满足强度要求,与普通平盖封头相比,减小了平盖的厚度,降低了结构总重量,对平盖封头的结构改进设计具有一定指导作用。     

Vegetation cover at right of way locations

This research evaluated the status of vegetation cover at right of way locations. Site factors that contributed to low and high ground cover along roadsides and medians were identified. Twenty-nine roadside and median study sites incorporated variability in soil type, elevation, vegetation establishment and cover, seed mixture, slope, aspect, time since planting, and climate. Vegetation cover was measured, and species distribution was identified. Slopes, aspects of the sloping face, and elevations were recorded. Soil samples were tested for nutrients, minerals, texture, and pH. Approximately 50% of the test sites met the 70% cover criteria. Locations of the worst cover (<50%) had soils with high soluble salt content (0.36–1.54 mmhos/cm) or low organic matter values (<1.7%). Vegetation cover was dominated by tall fescue (Festuca arundinacea) and crownvetch (Coronilla varia L.), two species that were included in the current seeding mixture and are considered invasive. To further promote revegetation success and persistence, both maintenance and site specific seed mixtures are needed.     

Local joint flexibility of tubular X-joints stiffened with external ring or external plates

In the present paper, the Local Joint Flexibility (LJF) of the ring-stiffened X-joints and plate-stiffened X-joints under compressive load is investigated. In the first phase, a finite element (FE) model was generated and verified with the results of available experimental tests and equations. In the next phase, a set number of 234 FE models were created to evaluate the role of the external ring size (β_r and τ_r), the external plate size (β_p and τ_p), and the connection geometry (γ, τ, and β) on the LJF factor (f_LJF). In these FE models, the weld connecting the chord and brace members was generated. The results indicated that the f_LJF of a plate stiffened joint can be down to 76% of the f_LJF of the corresponding un-stiffened joint. Also, the effect of the ring size on the f_LJF was more than the effect of the plate size on the f_LJF, because of the stiffener position. Despite the notable effect of the ring and the plate on the f_LJF, there is not any study or formula on tubular connections stiffened with ring or plate. Therefore, the FE results were used to propose two parametric formulas for determining the f_LJF in X-joints with external ring or external plate under brace compressive load. Moreover, the derived formulas were checked based on the UK DoE acceptance criteria.     

低温独立液舱曲面外板加工减薄量评估

基于耐低温合金材料的非线性特性,以某液化气船的低温独立液舱曲面外板加工成形过程为研究对象,研究其塑形变形过程及机理。利用ABAQUS作为计算分析工具,建立了板材原料及上、下加工模具的分析模型,给定冲压成形的时间和初始速度,并设定时间步长,考察每个时间步长的计算结果,分析了其加工过程中的弹塑性变形过程,评估了低温合金材料在加工过程中的板厚变化情况,并与实际加工测量值进行对比,验证了模型和计算分析过程的准确性。为各类低温独立液舱的设计和材料尺寸选用提供了技术支持和指导。     

某商用车散热器面罩开裂分析与改进

为解决散热器面罩开裂问题,提出了焊点优化方案和散热器面罩加强板外置/加强板内置方案,并进行了模块化设计,制定了2组改进措施。有限元分析结果表明:2种改进措施与原状态相比,均有良好应力改善效果,满足应力要求。     

基于多种失效模式SPS复合钢板替换船用钢板的优化设计

在SPS复合钢板的设计中获取不同的失效模式。以减重为目标,应用序列二次规划法对SPS复合钢板进行等效船用钢板的优化设计,同时对SPS复合钢板进行多目标优化,应用层次分析法定各目标的权重。在这两种优化方法的基础上,对船用钢板与SPS复合钢板进行了屈曲、弯曲对比数值分析,同时将结果与理论计算结果对比分析。结果表明,SPS复合钢板重量能够减轻37%以上,刚度增加两倍多,但厚度增加70%。