基于PWM整流器的交流调速系统的仿真

将PWM整流技术引入交流调速系统。在PWM整流侧采用直接功率控制技术，实现交流侧的高功率因数；电机控制采用矢量控制技术，实现电机调速的高性能。通过Matlab／Simulink仿真，可以验证这种调速策略可以实现整个系统的功率因数接近于1，减少对电网的污染，并且可以保证电机有着优良的调速性能。     

The dynamic response of rail support

This research reviews principles behind the dynamic response of rail supports, and introduces a method of analysis to find the maximum response in a realistic setting. Assuming a time-dependent, moving mass with massive wheels is essential, because the ratio of the moving mass to the rail mass is significant. However, the dynamic response of the track is not affected by dynamic properties of the train other than its unsprung mass, because the natural frequencies of the train suspension and track are significantly different. A numerical method is developed to model the dynamic response based on these principles, and applied to the Korean urban transit. The dynamic response includes multiple peaks with a large amplitude range, creating noise while the wheel passes the support. The dynamic impact factor (DIF) for the rail support depends mainly on the stiffness and damping of the rail support. The DIF for the rail moment is below the code value, whether this value is based on numerical analysis or on-site measurements. However, our numerical analysis results in a DIF for support settlement that is greater than the code value, if the damping is less than 3%.     

摆式车辆液压缸载荷的确定

详细介绍了摆式车辆液压倾摆系统的机构动作、车体复原力矩与液压缸脉冲加载时间的确定和液压缸载荷的计算。     

Dynamics of railway wagons subjected to braking torques on defective tracks

It is well known that track defects cause profound effects to the dynamics of railway wagons; normally such problems are examined for cases of wagons running at a constant speed. Brake/traction torques affect the speed profile due to the wheel–rail contact characteristics but most of the wagon–track interaction models do not explicitly consider them in simulation. The authors have recently published a model for the dynamics of wagons subject to braking/traction torques on a perfect track by explicitly considering the pitch degree of freedom for wheelsets. The model is extended for cases of lateral and vertical track geometry defects and worn railhead and wheel profiles. This paper presents the results of the analyses carried out using the model extended to the dynamics of wagons containing less ideal wheel profiles running on tracks with geometry defects and worn rails.     

ISG hybrid powertrain: a rule-based driver model incorporating look-ahead information

According to European regulations, if the amount of regenerative braking is determined by the travel of the brake pedal, more stringent standards must be applied, otherwise it may adversely affect the existing vehicle safety system. The use of engine or vehicle speed to derive regenerative braking is one way to avoid strict design standards, but this introduces discontinuity in powertrain torque when the driver releases the acceleration pedal or applies the brake pedal. This is shown to cause oscillations in the pedal input and powertrain torque when a conventional driver model is adopted. Look-ahead information, together with other predicted vehicle states, are adopted to control the vehicle speed, in particular, during deceleration, and to improve the driver model so that oscillations can be avoided. The improved driver model makes analysis and validation of the control strategy for an integrated starter generator (ISG) hybrid powertrain possible.     

综合管廊有偿使用收费方式及其适用性探究

采用理论研究和案例分析法针对城市地下综合管廊有偿使用收费方式进行了详细的探讨，并依托成都市IT大道地下综合管廊工程，同时借鉴了日月大道、成洛大道、成渝高速入城段等试点管廊的相关参数测算综合管廊有偿使用费，其中入廊费和日常维护费分别采用直埋成本法和空间比例法进行计算，建立了成都市地下综合管廊入廊费和日常维护费收费标准。研究结果表明采用该方法测算得到的成都市管线入廊费和日常维护收费标准较适应管线现状实际建设和运维情况，更易让各管线单位接受。     

绞吸挖泥船轴扭矩及功率测试

针对绞吸挖泥船轴扭矩及功率测试的问题,进行了现场测试和泥泵性能试验,介绍了一种绞吸挖泥船轴扭矩及轴功率测试试验装置。采用船舶应变片式轴功率测量方法,得出泥泵在850、900、950、1 000 r/min共4个转速下的泥泵性能参数;并对柴油机在945 r/min转速下,油门刻度18时的瞬时扭矩和平均扭矩进行计算。得出结论：在流量不变的情况下,泵的转速越高,扬程越高、功率越高;在流速在1~1.51 m3/s时,泥泵在4个转速下的水功率十分接近;随着流量的增大,转速越大,泵的水功率越高。     

转矩传感器磨损造成汽车跑偏的原因分析

针对市场某车型基本存在转向左跑偏的现状,根据转矩传感器的原理,对转矩传感器的主要部件尺寸进行测量分析,找出跑偏的原因,并模拟试验进行验证。     

基于共同规范的散货船屈曲强度评估

依据散货船共同结构规范的要求对某散货船船中区域主要结构进行屈曲强度直接计算,重点分析其屈曲强度,对不满足屈曲强度要求的板格进行加强,结果表明,共同规范对船体结构的要求更高。     

基于BEM/FEM计算浸水结构振动特性

应用直接边界元和有限元方法分析水下结构体的固有频率和振动特性,根据边界元理论编译出相应的程序来计算水下结构的附加质量矩阵,将附加质量矩阵与现有的有限元程序相结合,分析水下结构体的固有频率和振动特性,以浸没于流体介质中的圆柱壳为例,通过与近似理论值的对比验证了数值计算结果的可靠性,表明流体介质改变了结构的振动特性.