液力变矩器焊接的数值模拟和质量控制

对液力变矩器的制造精和质量要求很高，焊后必须保证产品的尺寸精度，并要进行疲 试验以考虑焊缝的强度。通过分析计算，可以预测各种条件对焊接变形的影响；发现疲劳承载时的最危险断面在不在焊缝处，而是在上盖板的弯角处。     

喷油泵装配线中拧紧技术的研究及应用

本论文介绍了拧紧技术的原理和方法,以及拧紧技术在喷油泵装配线中的应用.最后说明了拧紧程序在喷油泵装配线中的程序防错方法.     

Observer-based clutch disengagement control during gear shift process of automated manual transmission

A clutch disengagement strategy is proposed for the shift control of automated manual transmissions. The control strategy is based on a drive shaft torque observer. With the estimated drive shaft torque, the clutch can be disengaged as fast as possible without large driveline oscillations, which contributes to the reduction of total shift time and shift shock. The proposed control strategy is tested on a complete powertrain simulation model. It is verified that the system is robust to the variations of driving conditions, such as vehicle mass and road grade. It is also demonstrated that the revised system with switched gain can provide satisfactory performance even under large estimation error of the engine torque.     

热扰动对冻土区片块石路基热状态变化特性的影响研究

随着我国现阶段的公路建设里程不断增长,相较于常规平原地区,高寒冻土区公路建设过程要克服冻土路基带来的各类不良影响。针对热扰动对冻土区片块石路基带来的影响进行深入研究,在分析该区域高等级公路路基状态的过程中,采集片块石路基的温度状态、吸放热状态和冻融循环状态等方面数据,探讨了其热状态变化的整体规律。研究结果显示:片块石路基在冻土区有着很好的热稳定性作用,可实现主动冷却作用;片块石路基能通过加快温差空气间的流通速度,避免热扰动对路基温度产生过于明显的影响,从而减少热扰动所带来的各类路基病害;片块石路基正下方的最大融化深度正逐步提高;片块石路基的阴阳面存在吸放热不平衡的情况,阳面路肩吸放热量达到阴面路肩吸放热量的2.7倍,阳面坡脚吸放热量达到阴面坡脚吸放热量的2.3倍;随着片块石路基阴阳面吸放热不平衡的发展,其对应的阴面冻土升温速度小于阳面冻土,阴面冻土上限发展程度同样小于阳面冻土。     

Analysis on Ground Surface Deformation and Influence of Construction Parameters Caused by Two Different Shield Machines in Double-tube Tunnelling北大核心CSCD

Based on a shield-driven running tunnel project of Hangzhou Metro Line 2, this paper carries out field measuring of the ground surface deformation caused by two different shield machines in double-tube tunnelling in soft soil areas, obtains the laws of the surface deformation caused by shield-driven double-tube tunnelling and verifies the applicability of the modified Peck formula to double-tube tunnelling. The results show that in soft soil areas the impacts on ground surface deformation caused by different shield construction parameters in the previously and subsequently excavated tunnels are different, while the surface deformation changes sharply before and after the shield machine passing through the cutting face, and a rebound phenomenon occurs when the shield tail passes through the cutting face due to the influence of the grouting; The cutterhead torque of the shield machine in soft soil areas can be composed of five calculation factors, and the calculation results are in good agreement with the measured values. The larger the opening rate of the shield cutterhead is, the larger the average torque value will be, the higher the percentage of large ground loss rate will be, and the larger the maximum ground surface settlement will be; The ratio of cutterhead torque T to mucking volume per ring Q is used as the control parameter for analyzing the ground surface settlement, and a certain positive correlation between the ratio and the surface settlement value is determined, the smaller the cutterhead opening rate is, the more accurate the fitting results will be. © 2022, Editorial Office of "Modern Tunnelling Technology". All right reserved.     

基于数字信号处理的直接转矩控制研究

直接转矩控制因控制简单、具有优良的动静态特性，在电机控制中应用越来越广泛。但它在低速区的局限也较多。随着数字信号处（Digital Signal Processing，缩写DSP）技术的发展，使得改善其低速控制特性成为可能。文中简介了直棼转矩控制技术的特点、控制原理及难点，探讨了一种应用DSP技术的直接转矩控制方法。     

Flexural gravity wave generation by initial disturbances in the presence of current

The effect of uniform current on the generation of flexural gravity waves resulting from initial disturbances at a point was analyzed in two dimensions. The problem was formulated as an initial boundary value problem under the assumptions of the linearized theory of water waves. By direct application of the Laplace transform and then the Fourier transform, explicit expressions for the velocity potential and free surface elevation were obtained in integral forms; these were evaluated asymptotically for large distances and times by the application of the method of the stationary phase to obtain the far field behavior of the surface elevations in specific cases. Simple numerical computations were performed to illustrate the effect of uniform current on the surface elevation, wavelength, phase velocity, and group velocity of the flexural gravity waves and on the far field behavior of the progressive waves in two different cases, namely, when there is an initial depression concentrated at the origin and an initial impulse concentrated at the origin.     

摆式车辆液压缸载荷的确定

详细介绍了摆式车辆液压倾摆系统的机构动作、车体复原力矩与液压缸脉冲加载时间的确定和液压缸载荷的计算。     

Dynamics of railway wagons subjected to braking torques on defective tracks

It is well known that track defects cause profound effects to the dynamics of railway wagons; normally such problems are examined for cases of wagons running at a constant speed. Brake/traction torques affect the speed profile due to the wheel–rail contact characteristics but most of the wagon–track interaction models do not explicitly consider them in simulation. The authors have recently published a model for the dynamics of wagons subject to braking/traction torques on a perfect track by explicitly considering the pitch degree of freedom for wheelsets. The model is extended for cases of lateral and vertical track geometry defects and worn railhead and wheel profiles. This paper presents the results of the analyses carried out using the model extended to the dynamics of wagons containing less ideal wheel profiles running on tracks with geometry defects and worn rails.     

ISG hybrid powertrain: a rule-based driver model incorporating look-ahead information

According to European regulations, if the amount of regenerative braking is determined by the travel of the brake pedal, more stringent standards must be applied, otherwise it may adversely affect the existing vehicle safety system. The use of engine or vehicle speed to derive regenerative braking is one way to avoid strict design standards, but this introduces discontinuity in powertrain torque when the driver releases the acceleration pedal or applies the brake pedal. This is shown to cause oscillations in the pedal input and powertrain torque when a conventional driver model is adopted. Look-ahead information, together with other predicted vehicle states, are adopted to control the vehicle speed, in particular, during deceleration, and to improve the driver model so that oscillations can be avoided. The improved driver model makes analysis and validation of the control strategy for an integrated starter generator (ISG) hybrid powertrain possible.