马鞍山长江公路大桥钢塔线形控制技术

马鞍山长江公路大桥左汊主桥为（360＋2×1080＋360） m的三塔两跨悬索桥，中塔采用钢－混叠合、塔梁固结门式结构，下塔柱为预应力钢筋混凝土结构，上塔柱为钢结构，钢塔共分21个节段，首节采用浮吊安装，标准节段长6 m ，最大起吊重达235 t ，采用塔吊进行安装。为确保钢塔线形满足要求，对影响钢塔安装精度因素进行分析，形成以控制钢塔制造质量为核心、钢塔首节段安装精度为基础的线形控制流程，对钢塔节段进行工厂制造控制和现场安装控制。工厂制造控制包括零部件加工、块体制作、节段组拼、端面机加工、预拼装；现场安装控制包括首节段安装、标准节段安装、横梁与钢塔的连接。实践表明，该桥采用以控制钢塔制造精度为核心的钢塔线形控制技术进行钢塔架设施工，施工过程中钢塔制造精度和安装精度满足要求，实现了钢塔线形控制的目的。     

广西普通高等教育经费来源结构的变化与分析——以2001-2011年教育经费统计数据为例

近十年来，广西普通高等教育经费来源结构已呈现出多元化趋势。但是普通高等教育经费总量仍显不足；经费来源结构不尽合理，二元格局明显；科研经费拨款所占比例过小；过于依赖学杂费的增加。广西高等教育未来发展所需的经费保障，要求必须真正实现经费来源的多元化。     

Detection of nonlinearity effects in structural integrity monitoring methods for offshore jacket-type structures based on principal component analysis

The detection of changes in the dynamic behavior of structures is an important issue in structural safety assessment. The development of detection methods assumes greater significance in the case of offshore platforms because the inherent problems are compounded by the harsh environment. Here, we describe an instrumented physical model for the structural health monitoring of an offshore jacket-type structure and the results of tests in several different damage scenarios. In a comparative investigation of two different methods, we discuss the difficulties of implementing damage detection techniques for complex structures, such as offshore platforms. The combined algorithm of a fuzzy logic system and a model updating method are briefly discussed, and a method based on stochastic autoregressive moving average with exogenous input is adopted for the structure. The consideration of uncertainties and the effects of nonlinearity were major objectives. So, the methods were also investigated based on the test scenarios consisting of the physical model with a geometric nonlinearity. The principal component analysis method was utilized for the detection of nonlinearity in the recorded data. The results show that the developed methods are suitable for damage classification, but the quality of the acquired signals must be considered an important factor influencing successful classification. The development of these methods may be extremely useful, as such technologies could be applied for offshore platforms in service, enabling damage detection with fewer false alarms.     

我国城市防洪排涝地下深隧规划设计与施工方法

为了建设符合中国国情的地下排水深隧,解决城市内涝问题,消除"城市看海"现象,采用调研分析的研究方法,通过调研国外城市排水深隧建设的成功案例,借鉴成熟经验并结合我国国情探索出我国城市排水深隧在规划设计、施工技术等方面的建设模式。主要结论如下:1)深隧规划必须坚持雨污分流原则,防涝标准应设为百年一遇;2)深隧层位应建于地下30~50 m的位置,隧道管线应布设在城市易涝区,并且将修建深隧、改造浅管和清淤河道衔接起来,形成一套完整的防洪排涝系统,让深隧的作用得以充分发挥,才能解决城市内涝问题;3)排水深隧要注重防水设计,防止雨水污染地下水;4)为提高深隧的经济效益,应将深隧与地下快速路的规划结合起来,功能上多样化。     

漫谈矿山法隧道技术第十四讲——隧道涌水及其控制方法

分析制定隧道控制地下水对策的基本观点:既要考虑隧道施工对地下水的影响,也要考虑地下水对隧道施工的影响。指出控制地下水的对策必须符合3个条件:1)确保施工作业安全、顺利地开展;2)不对周边环境产生有害的影响;3)以合理的工费和工期来实现。隧道涌水视其发生位置、涌水量、发生时期、涌水量的历时变化等是各种各样的,应对隧道涌水进行合理分类,以便有的放矢地采取相应的对策。介绍了日本统计的地质构造和涌水现象的分类。涌水处理应达到3个基本目标:1)确保隧道施工在无水的条件下进行,或者是在可以接受的渗漏水条件下进行,或者是在对周边环境"可接受干扰"的条件下进行;2)二次衬砌原则上不承受水压作用,不得已时把水压控制在二次衬砌容许的范围内;3)运营中的隧道洞内不能成为地下水流经的通道,隧道衬砌背后必须形成一个纵横交错的、不易堵塞的、通畅的排水系统。达到上述目标的基本方法是:充分利用和提高围岩的隔水性能,合理地处理好"排"与"堵"的关系。针对涌水处理的3个基本目标,分别介绍了国内外相应的经验和措施。1)一些国家的指南、标准对隧道的涌水量进行了分级,认为涌水量≤2.5 L/(min·m)时基本上可以认为是在无水条件下施工;一般的线状流水、经常涌水可以用自然排水法排水;而针对突发大量涌水,则需要采取特殊的地下水对策予以解决。2)按照二次衬砌是否承受水压,隧道可分为3种情况:1衬砌不承受水压,即所谓的完全排水型隧道;2衬砌承受全部水压,即所谓的非排水型(防水型)隧道;3衬砌背后设置注浆域,分担衬砌承受的水压,衬砌只承受部分容许的水压。从目前的隧道设计实际来看,在山岭隧道中多数采用方案1,在城市隧道中多数采用方案2,在高水压和突发大量涌水的极端情况下采用方案3。介绍了日本、美国的设计经验。3)我国铁路隧道采用把地下水引入隧道,再从洞内两侧边墙附近设置的排水沟排出地下水的做法是值得商榷的;特别是在可能发生冻害的地区,更不可取。在国外,日本、德国、法国等国家的铁路、公路隧道基本上是把中央排水管设置在仰拱内或仰拱下方,而在隧道两侧只留有用于排出流入隧道内的雨水或隧道清洗水的排水沟;因此,建议立项研究取消洞内排水沟,设置中央或两侧脚部排水管的问题。最后指出,实现涌水处理的3个基本目标我们尚需努力,特别是"目标"的定位问题,尚需进行基础性的研究才能解决。在隧道施工中,涌水是不可避免的、客观存在的现象,我们积累的经验非常丰富,但缺乏系统的、认真的总结和归纳。     

国Ⅴ柴油机SCR系统结构对尿素结晶影响研究

针对某国Ⅴ商用柴油车SCR系统中出现的结晶问题,综合应用CFD模拟和台架试验进行分析研究,提出一系列结构优化和改进方案,改善了SCR前流场状态以及流体的流动均匀性和尿素均匀性,基本消除了排气系统在实际工况下的结晶风险,提高了全系统的抗结晶能力,保证了SCR系统的正常运行。通过对模拟结果和台架试验数据的比对分析,研究了流场分布以及混合器结构对结晶形成产生的影响。     

桥面铺装复合梁的有限元分析

采用三维有限元法,分析了复合梁试件模型和实体桥面铺装模型中沥青混凝土铺装层表面的受力特性及其变化趋势。计算结果表明,复合梁模型和实体桥面铺装模型中的沥青铺装层表面的受力状态相同,变化趋势一致,采用试验可控性较好的复合梁试验能够模拟不同结构组合的桥面铺装层受力特性,为大跨径桥梁桥面铺装层结构设计、材料选择提供依据。     

高速公路中收费和清分的动态解决方案

在高速公路收费和清分过程中,由于新增的高速公路和收费站点特别是环型路段的增加使得原有的静态算法已经不适宜于现实情况。本文提出了高速公路中基于最短路径和环型路段的动态收费和清分解决方案,并给出了详细的基于环型路段的动态算法。环型路段问题解决后,可以判知车辆实际行车路线,从而大幅提高收费及清分的准确性和效率。     

现浇预应力混凝土连续箱梁桥设计

结合某主线上一座2×30 m现浇连续预应力混凝土葙梁桥的工程实例,较详尽的介绍了该桥的设计和构造特点、上部结构计算及上下部构造设计,并结合实际针对设计时应考虑的一些因素进行了较详细的探讨.     

A data model applied to the knowledge-based ICAS

Image-guided computer aided surgery system (ICAS) contributes to safeness and success of surgery operations by means of displaying anatomical structures and showing correlative information to surgeons in the process of operation. Based on analysis of requirements for ICAS, a new concept of clinical knowledge-based ICAS was proposed. Designing a reasonable data structure model is essential for realizing this new concept. The traditional data structure is limited in expressing and reusing the clinical knowledge such as locating an anatomical object, topological relations of anatomical objects and correlative clinical attributes. A data structure model called mixed adjacency lists by octree-path-chain (MALOC) was outlined, which can combine patient's images with clinical knowledge, as well as efficiently locate the instrument and search the objects' information. The efficiency of data structures was analyzed and experimental results were given in comparison to other traditional data structures. The result of the nasal surgery experiment proves that MALOC is a proper model for clinical knowledge-based ICAS that has advantages in not only locating the operative instrument precisely but also proving surgeons with real-time operation-correlative information. It is shown that the clinical knowledge-based ICAS with MALOC model has advantages in terms of safety and success of surgical operations, and help in accurately locating the operative instrument and providing operation-correlative knowledge and information to surgeons in the process of operations.