土工格栅在治理沥青路面裂缝中的应用

裂缝是沥青路面常见病害。应用非织造土工织物——多功能双向土工格栅治理高等级公路沥青路面的裂缝,取得了良好的效果,并对土工格栅的应用进行了定量计算。     

石河道大桥桩基础施工

针对卵石地层桩基础成孔问题,根据石河道大桥实际施工实践介绍了应用冲击钻孔的方法加以解决的施工方法,并着重分析了该方法的工艺流程和内容,以及施工中的注意事项.     

FRP正弦波形夹心桥面板的等效有限元模型

以FRP正弦波形夹心桥面板作为研究对象,得到等效正交各项异性实心板,通过理论分析和数值对比,证明了方法的可行性;采用该法对一实际的FRP正弦波形夹心板桥进行了模态分析。     

Determination of Critical Slip Surface of Soil Slope

A new complex method is presented considering not only the improvement upon the ＂bad ＂design point, but also the diversity of the newly generated complex, which is obtained by replacing the ＂bad ＂design point with the better design point located at the line between the ＂bad ＂design point and the ceotroid of the remaining design points of the old complex. The new complex method is applied to searching for the critical slip surface of two non-homogeneous soil slopes. The comparison of the results obtained by the new complex method with that by the basic complex method shows that the new complex method is much more likely to find the true critical surface for the randomly generated initial complex.     

基于ANN星识别算法的仿真平台

星敏感器是一种高精确度的姿态测量仪器，它通过对观测到的星点进行识别来计算姿态。为了能够较好地测试和验证星识别系统的性能，设计了一个基于ANN算法的星识别仿真平台。通过对该星识别仿真平台性能的测试，表明该仿真平台能够方便，实时地测试星识别算法的性能与正确性，因此说它是一种具有较好实用价值的星识别仿真平台。     

Mixed analysis of shell and solid elements using the overlaying mesh method

 This article presents a mixed method of analyzing shell elements and solid elements using the overlaying mesh method. In the structural design of a ship's hull, the shell elements are used for the global model. However, the solid elements are necessary to analyze the stress concentration zones or the vicinity of a crack. In such cases, the models are analyzed using zooming analysis, in which the results of a global model analysis are transferred to a local model analysis by imposing boundary conditions. This method is more advantageous than zooming analysis in terms of the accuracy of the solution and the modeling flexibility. Some examples of a plate model with a cracked surface or with a projection are shown in order to demonstrate the effectiveness of the method. Received: August 6, 2002 / Accepted: November 25, 2002 Address correspondence to: S. Nakasumi (sumi@nasl.t.u-tokyo.ac.jp) Updated from the Japanese original, which won the 2002 SNAJ prize (J Soc Nav Archit Jpn 2001;189:219–224; and 190:655–662)     

Numerical simulation of the flow about self-propelling tanker models

A time-marching CFD simulation is performed for self-propelling ships. The flow about the hull is simulated by the finite-volume method, and the propeller action is approximated as a propeller disk for which the solution is given by a simplified propeller model. The interaction of two flow models is treated in a time-marching procedure converging towards the steady self-propelling condition. This method is applied to five tanker models, and detailed comparisons are made between the simulated results and corresponding experimental results. It is shown that the flow field in the self-propelling condition is qualitatively well reproduced in the simulation, and the estimated thrust deduction factors for the five hull forms agree well with measured ones. However, the effective wake factors are underestimated, since the Reynolds number in the simulations differs from that in the experiment.     

模拟异种钢接头蠕变力学特性的数值分析

利用有限元数值模拟了高强匹配异种的接头在弹性－蠕变条件下的应力／应变场，结果表明，接头的应力／应变分布不均匀，在焊缝界面上，应力和应变分别呈不连续和不协调分布特性，并随着拦头各区蠕变强度差别的增大，其分布梯度增大，峰值应力／应变提高，因此，蠕变强度梯度大的高强焊缝和低强母材的界面是接头的薄弱部位。     

Dynamic Simulation of a Smart Crank and Slider Mechanism

In this paper, a smart crank and slider mechanism is analyzed mostly from a dynamic view. By means of dynamic explicit finite element method, 3D nonlinear structure is simulated. It is proved that the mechanism can effectively accomplish smart movement prescribed. And in order to ensure reciprocal movement with higher frequency, measures should be taken to avoid over heating of parts. Compared with internal energy, kinetic energy of total rigid body is dominating, and Y direction equivalent rigid velocity is much higher than X direction velocity. Equivalent rigid velocity of all parts is consistent with respective movement condition. For both energy and velocity, slider effect is dominating. Three direction equivalent inertia force oscillates. Force amplitude in Y -direction is comparitively the greatest.     

应用复合梁单元实现钢管混凝土拱桥的极限承载力分析

进行大跨度钢管混凝土拱桥的极限承载力分析,需要综合考虑几何和材料非线性、混凝土收缩和徐变、温度变化等多种因素的影响。本文从固体力学的基本理论出发,建立适于考虑上述诸多因素的复合梁单元,阐述了基于该单元的钢管混疑土拱桥极限承载力分析程序的实现方法,并通过与一个哑铃形截面钢管混凝土组合式拱肋极限承载力试验结果的对比验证了其可行性。