侧滑仪与检测工作站通信技术研究

汽车前轮定位参数的正确与否,对汽车的行驶平顺性、安全性、秉坐的舒适性及操纵的灵巧等方面有很大影响.因此,作为前轮定位参数的重要部分--侧滑量的检测在汽车检测系统中占有不可或缺的地位.     

现浇薄壁筒桩技术及其施工工艺

介绍现浇混凝土薄壁筒桩技术以及与其它形式桩基技术的比较.     

动力总成悬置支架多目标拓扑优化和强度分析

基于Optistruct,以支架的最小柔度、最大固有频率作为优化目标函数;以应力、体积作为约束函数,对一发动机后拉杆安装支架进行拓扑优化,优化结果表明:在满足悬置支架强度和模态要求下,质量减少了12%。     

弹簧支吊架在FPSO高温管道中的应用

高温条件下管道热胀、冷缩和端点附加位移产生的位移载荷是造成管道应力过大和相连设备管口扭矩、反力过大的主要因素。合理设计管道走向和支架布置来增加管道系统柔性是减小管道热载、降低管道应力的主要途径。以机舱排烟管道系统为例,在CAESAR II中建立数值模型,分析了排烟管道的热胀载荷对管道的影响,比较了弹簧支架约束与刚性支架约束对高温排烟管道一次、二次应力的影响。研究发现,在高温管道中,弹簧支吊架不仅能增加管道系统的柔性,减小管道热应力,而且能降低管道对支架的约束载荷,减小管道所受的集中力。     

船舶轴系的合理轴承间距的研究

在综合考虑轴承许用比压、轴承安装误差以及轴系横振等限制条件下,以船舶轴系的轴承负荷分配的合理性为目标,分析了船舶轴系的合理轴承间距问题,给出了轴系计算模型及方法,并以SDTS船舶轴系实验台为例进行计算,得到了轴系合理轴承间距下的优化校中状态,轴系热态运行工况明显改善。     

肘板对肋骨侧向稳定性的影响

通过研究在环肋圆柱壳的肋骨周向均匀布置肘板,得到肘板能有效限制肋骨的侧向变形,改善肋骨的侧向稳定性,提高肋骨的临界失稳压力,通过对比分析半肋距肘板和整肋距肘板,得到整肋距肘板对肋骨的侧向约束效果更明显,更有利于提高肋骨的侧向稳定性,最后得出整肋距肘板能有效提高肋骨的侧向稳定性和圆柱壳的整体稳定性。     

非刚性轴承润滑与变形耦合下的轴系校中研究

轴承油膜是影响轴系校中的动态因素之一。在油膜刚度的计算过程中,较多学者采用船级社推荐值,或将轴承考虑为刚性,利用差分法或有限元法对其进行求解。文章对轴承弹性变形与油膜压力进行耦合分析,获得最优小扰动量,得到更符合实际情况的油膜刚度,利用vb.net编写有限元轴系校中软件并对某油船轴系进行校中计算,分析了轴承油膜对轴系校中的影响程度,可为船舶轴系校中计算及检验提供参考。     

The structure of dissipation in the western Irish Sea front

We report on an intensive campaign in the summer of 2006 to observe turbulent energy dissipation in the vicinity of a tidal mixing front which separates well mixed and seasonally stratified regimes in the western Irish Sea. The rate of turbulent dissipation ε was observed on a section across the front by a combination of vertical profiles with the FLY dissipation profiler and horizontal profiles by shear sensors mounted on an AUV (Autosub). Mean flow conditions and stratification were obtained from a bed mounted ADCP and a vertical chain of thermistors on a mooring. During an Autosub mission of 60 h, the vehicle, moving at a speed of ~ 1.2 m s^− 1, completed 10 useable frontal crossings between end points which were allowed to move with the mean flow. The results were combined with parallel measurements of the vertical profile of ε which were made using FLY for periods of up to 13 h at positions along the Autosub track. The two data sets, which show a satisfactory degree of consistency, were combined to elucidate the space–time variation of dissipation in the frontal zone. Using harmonic analysis, the spatial structure of dissipation was separated from the strong time dependent signal at the M₄ tidal frequency to yield a picture of the cross-frontal distribution of energy dissipation. A complementary picture of the frontal velocity field was obtained from a moored ADCP and estimates of the mean velocity derived from the thermal wind using the observed density distribution. which indicated the presence of a strong (0.2 m s^− 1) jet-like flow in the high gradient region of the front. Under neap tidal conditions, mean dissipation varied across the section by 3 orders of magnitude exceeding 10^− 2 W m^− 3 near the seabed in the mixed regime and decreasing to 10^− 5 W m^− 3. in the strongly stratified interior regime. The spatial pattern of dissipation is consistent in general form with the predictions of models of tidal mixing and does not reflect any strong influence by the frontal jet.     

浅谈轴系校中计算及Nauticus Shaft Alignment软件的应用

本文以介绍轴系校中的计算方法为主,同时简单介绍Nauticus Shaft Alignment软件在计算过程中的应用。轴系校中的目的在于通过调整各轴承的合理位置,使各个轴承上的负荷在各种工况下均能合理分配。     

船舶轴带发电机的发展与新方法的研究

现在广泛使用的船舶轴带发电机系统控制相对简单,但对船舶电网中的电能质量影响大,并且需要依靠同步发电机来补偿无功等缺点。本文在分析了轴带发电机发展历程与工作过程的基础上,介绍一种新型的轴带发电机模式,利用全控型PWM整流器的四象限运行功能,实现有功、无功的快速调节。给出了整个系统的主电路与控制方案,从理论上解释了这种新的轴带发电机系统的正确性和可行性。