A signal-based fault detection and classification method for heavy haul wagons

This paper proposes a signal-based fault detection and isolation (FDI) system for heavy haul wagons considering the special requirements of low cost and robustness. The sensor network of the proposed system consists of just two accelerometers mounted on the front left and rear right of the carbody. Seven fault indicators (FIs) are proposed based on the cross-correlation analyses of the sensor-collected acceleration signals. Bolster spring fault conditions are focused on in this paper, including two different levels (small faults and moderate faults) and two locations (faults in the left and right bolster springs of the first bogie). A fully detailed dynamic model of a typical 40t axle load heavy haul wagon is developed to evaluate the deterioration of dynamic behaviour under proposed fault conditions and demonstrate the detectability of the proposed FDI method. Even though the fault conditions considered in this paper did not deteriorate the wagon dynamic behaviour dramatically, the proposed FIs show great sensitivity to the bolster spring faults. The most effective and efficient FIs are chosen for fault detection and classification. Analysis results indicate that it is possible to detect changes in bolster stiffness of ±25% and identify the fault location.     

Influence of AC system design on the realisation of tractive efforts by high adhesion locomotives

The main task for heavy haul railway operators is to reduce the cost of exported minerals and enhance the long-term viability of rail transport operations through increasing productivity by running longer and heavier trains. The common opinion is that this is achievable by means of implementation of high adhesion locomotives with advanced AC traction technologies. Modern AC high adhesion locomotives are very complex mechatronic systems and can be designed with two alternative traction topologies of either bogie or individual axle controls. This paper describes a modelling approach for these two types of AC traction systems with the application of an advanced co-simulation methodology, where an electrical system and a traction algorithm are modelled in Matlab/Simulink, and a mechanical system is modelled in a multibody software package. Although the paper concentrates on the analysis of the functioning for these two types of traction control systems, the choice of reference slip values also has an influence on the performance of both systems. All these design variations and issues have been simulated for various adhesion conditions at the wheel–rail interface and their influence on the high traction performance of a locomotive equipped with two three-axle bogies has been discussed.     

沉船油舱抽油加热过程的热力学分析

本文对沉船倾斜油舱抽油过程进行了数值模拟研究,在相同的蒸汽加热功率,不同的加热位置条件下,分析了油舱内重质燃油和原油的加热过程,分别取得了在不同时刻油舱内重质燃油和原油的温度分布情况,以及油温随加热时间的变化规律。     

FLNG总体设计关键技术研究

阐述了集天然气预处理、液化、储存、外输为一体的新型海上浮式装置FLNG总体设计中的几项关键技术。提出控制船体运动性能的重要性,从主尺度选择、线型设计和典型配载工况等方面入手进行分析,确定250,000m3 FLNG船体主尺度,以确保上部生产系统高效率的正常作业。针对LNG货物围护系统,提出薄膜型(双排舱)和SPB独立舱型两种货物围护系统方案,并从上部模块支墩设置和隔离舱加热等方面对这两个方案进行比较。论述FLNG冷却海水供应系统的特点及其与常规海底门取水方法的不同之处,提出舷外海水提升泵取水的可行方案。     

浅析西门子BDPC系统在CTV上的 可行性

本文主要目的是分析西门子Blue Drive Plus C（随后简称BDPC）系统及其配置是否能够应用在深水动力定位原油输送船（随后称CTV）上。通过供需关系对比法,首先实现CTV实现海上自由航行、跟随定位、连接FPSO与～30万吨油轮之间浮管、加油跟随定位、紧急脱离、绿色环保运行等工况下的正常与应急储备动力需求,随后分析西门子BDPC直流系统及其运用技术,针对本项目提供的特殊配置,与CTV提出需求进行对比,结论是BDPC依靠它的直流发电、配电、逆变、储能等技术,可以满足CTV的配置需求,论证了BDPC系统运用在性能优越的深水原油输送装置CTV是可行的。     

6500m~3液化气运输船鞍座结构强度分析

论述中小型液化气船C型独立液货舱液罐鞍座结构及其作用,根据《散装运输液化气体船舶构造与设备规范》,采用有限元分析方法对一艘6 500 m3液化气船的鞍座及其附近船体结构在不同工况下进行了结构强度评估。通过计算分析,提出具有一定工程参考价值的修改建议,为确保6 500 m3液化气船在不同工况下的安全性提供技术保证。     

最首尾货舱直接强度评估研究

针对CSR-H关于最首尾货舱有限元分析在实际评估中可能存在的技术问题进行研究分析。通过理论分析与数值试验相结合对最首尾货舱有限元评估方法中的边界条件、力学模型、模型范围进行合理性评估,通过已建造船数值试验对最首尾货舱开展有限元直接强度评估。数值分析结果表明两端简支的边界条件能较好的模拟翘曲效应,模型范围对强度评估结果有影响。最首货舱离边界很近会导致甲板、外板的屈曲强度不满足要求。而CSR-H针对最尾货舱有限元中的剪力调整方法仍基于货舱中段,仅以货舱前后端壁剪力为目标值进行调整,这种剪力调整方法不适用于最尾货舱。     

宁波光明通用泊位工程整体改造工艺设计

介绍宁波光明通用泊住升级改造工程工艺系统改造的思路和方案。在不影响现有生产的前提下,通过调整工艺流程和更新装卸设备,使泊位等级和装卸设备配置与实际到港船型匹配,工艺流程更加合理。改造后码头通过能力显著提高,码头卸船能力与堆场能力相适应。     

自动化集装箱码头总体布置

我国作为世界第一大集装箱生产、运输国,至今尚未有一座自动化集装箱码头投产运营,开展自动化码头总体布置研究是自动化集装箱码头建设的关键。结合国内外自动化集装箱码头应用发展状况,总结自动化集装箱码头几种常见的布置形式和特点,针对某工程建设设想,制定全自动化码头总体布置技术方案,提出相关意见和建议,可供类似工程参考。     

集装箱船装运危险货物的适用规则解读

分析了船上危险货物的种类及防爆要求。通过解读规范要求,整理出集装箱船可运输的危险品种类及特殊要求。根据运输危险货物的要求,归纳总结集装箱船设计中应该注意的供水、通风、人员保护和机器处所限界面隔热等问题,并提出设计运输危险货物的集装箱船时应遵循的主要原则。