Robust traffic assignment model: Formulation,solution algorithms and empirical application

ABSTRACT

The deterministic traffic assignment problem based on Wardrop's first criterion of traffic network utilization has been widely studied in the literature. However, the assumption of deterministic travel times in these models is restrictive, given the large degree of uncertainty prevalent in urban transportation networks. In this context, this paper proposes a robust traffic assignment model that generalizes Wardrop's principle of traffic network equilibrium to networks with stochastic and correlated link travel times and incorporates the aversion of commuters to unreliable routes.

The user response to travel time uncertainty is modeled using the robust cost (RC) measure (defined as a weighted combination of the mean and standard deviation of path travel time) and the corresponding robust user equilibrium (UE) conditions are defined. The robust traffic assignment problem (RTAP) is subsequently formulated as a Variational Inequality problem. To solve the RTAP, a Gradient Projection algorithm is proposed, which involves solving a series of minimum RC path sub-problems that are theoretically and practically harder than deterministic shortest path problems. In addition, an origin-based heuristic is proposed to enhance computational performance on large networks. Numerical experiments examine the computational performance and convergence characteristics of the exact algorithm and establish the accuracy and efficiency of the origin-based heuristic on various real-world networks. Finally, the proposed RTA model is applied to the Chennai road network using empirical data, and its benefits as a normative benchmark are quantified through comparisons against the standard UE and System Optimum (SO) models.     

Travel time estimation oriented freeway sensor placement problem considering sensor failure

Optimal sensor placement on freeway corridor is of great interest to transportation authorities. However, current traffic sensors are easily subject to various failures. Therefore, it is necessary to incorporate sensor failure into the optimal sensor placement model. In this article, a two-stage stochastic model is proposed for the purpose of travel time estimation on freeway corridor. To balance the effectiveness and reliability, a stochastic conditional value at risk (CVaR) model is also proposed. Since both models are too complicated, a customized genetic algorithm is developed. Numerical experiments show that considering sensor failure makes a significant performance improvement in the sensor placement pattern. Sensitivity analysis is also applied to investigate the impact of a number of allowable sensors and different traffic sensor failure probability.     

汕头苏埃隧道方案设计关键技术研究

根据汕头苏埃隧道的建设条件,对工程方案设计中的几个技术难点进行研究,并提出解决方案。通过采用"多级分流"理念,实现隧道与北岸4条城市主干道的交通衔接;选择"抛石+排水板"方案解决海域深厚淤泥地层中的围堰设计;8度高烈度震区选择合理的抗震减震措施解决隧道结构抗震;采取双道密封垫和加大密封垫断面的防水设计,满足地震时管片接缝张开量大的防水要求;针对复杂地层,对盾构选型和配置提出建议;对海底凸起进入隧道内的硬岩进行爆破预处理,以降低盾构施工风险。     

基于灰色理论的雪山梁隧道施工过程渗漏水水源识别研究

为了解决黄龙景区雪山梁隧道开挖过程中的涌水水源识别问题,结合黄龙景区雪山梁隧道的相关施工资料,依据已有的地质资料和涌突水预测,通过水分析化学实验,采用灰色理论计算方法研究不同水系之间的关联度;而后针对单一水源和混合水源分别进行试验和分析,得出雪山梁隧道出口段内渗漏水来源最可能为大气降水,关联度较高的还有淘金沟上游水系和隧道出口处水系;最后进行比对,得出隧道渗漏水主要来源是大气降水和淘金沟上游水体的结论,并依据现场资料及实地踏勘,验证了灰色理论分析结果的可靠性。     

小直径盾构施工中管片纵向应力监测研究

为了探索小直径盾构法隧道在施工过程中管片纵向应力的变化规律,对北京槐房再生水厂污水隧道管片纵向应力进行了现场监测:将第976环、第1 054环管片分别设为第1和第2监测断面,2监测断面各预埋5个纵向应力计,各监测断面从本监测断面管片安装后即开始监测,当盾构掘进至第1 129环时停止监测。研究表明:1)在管片离开盾尾50环后,其纵向应力波动值小于管片拼装期间应力值的5%。2)在盾构掘进期间,管片距离盾构越远,其纵向压应力值越小。3)在管片拼装期间,管片距离盾构越远,其纵向压应力经历了先增大后减小的过程。4)管片距离盾构108环后,该管片纵向压应力趋近于0.2~0.3 MPa。5)随着盾构推进,管片纵向应力经历了4个阶段的变化过程,即周期性剧烈波动阶段—动态稳定阶段—逐渐衰减阶段—趋于稳定阶段。     

薄基岩顶板隧道爆破施工围岩稳定性分析

为更有效地进行薄基岩顶板条件下隧道施工安全控制,以某高速公路隧道为工程背景,运用数值模拟的方法,分别研究不同顶板厚度下隧道爆破施工引起的围岩振速分布特征及其对围岩的损伤情况,并进行围岩稳定性分析。结果表明:1)当顶板厚度在5 m及以上时,围岩是稳定的;2)当顶板厚度为3 m时,最危险横断面上基岩顶板内开始产生严重的拉伸裂缝及一些径向裂缝,将形成超挖;3)当顶板厚度≤2 m时,径向裂缝贯穿顶板岩体,围岩稳定性较差,在掌子面后1 m内可能发生塌落、掉块等事故。     

极高地应力软岩隧道超前导洞应力释放及多层支护变形控制技术

为了解决极高地应力软岩隧道大变形控制难题,以兰渝铁路木寨岭隧道岭脊核心段施工为例,通过现场试验和数据分析,得到如下主要结论:1)提出了"先放后抗,抗放结合,锚固加强"的变形控制理念;2)得出了该隧道岭脊核心段"超前导洞应力释放+圆形4层支护结构+径向注浆+长锚杆+长锚索"综合变形控制方案;3)超前导洞应力释放效果明显,正洞累计变形减小幅度约为34%;4)得到了圆形多层支护结构变形规律;5)累计变形均控制在设计预留变形量内,保证了该隧道岭脊核心段大变形控制效果。     

The Kalker book of tables for non-Hertzian contact of wheel and rail

A new regularisation of non-elliptical contact patches has been introduced, which enables building the look-up table called by us the Kalker book of tables for non-Hertzian contact (KBTNH), which is a fast creep force generator that can be used by multibody dynamics system simulation programs. The non-elliptical contact patch is regularised by a simple double-elliptical contact region (SDEC). The SDEC region is especially suitable for regularisation of contact patches obtained with approximate non-Hertzian methods for solving the normal contact problem of wheel and rail. The new regularisation is suitable for wheels and rails with any profiles, including worn profiles.

The paper describes the new procedure of regularisation of the non-elliptical contact patch, the structure of the Kalker book of tables, and parameterisation of the independent variables of the tables and creep forces.

A moderate volume Kalker book of tables for SDEC region suitable for simulation of modern running gears has been computed in co-simulation of Matlab and program CONTACT.

To access the creep forces of the Kalker book of tables, the linear interpolation has been applied.

The creep forces obtained from KBTNH have been compared to those obtained by program CONTACT and FASTSIM algorithm. FASTSIM has been applied on both the contact ellipse and the SDEC contact patch. The comparison shows that KBTNH is in good agreement with CONTACT for a wide range of creepage condition and shapes of the contact patch, whereas the use of FASTSIM on the elliptical patch and SDEC may lead to significant deviations from the reference CONTACT solutions.

The computational cost of calling creep forces from KBTNH has been estimated by comparing CPU time of FASTSIM and KBTNH. The KBTNH is 7.8–51 times faster than FASTSIM working on 36–256 discretisation elements, respectively.

In the example of application, the KBTNH has been applied for curving simulations and results compared with those obtained with the creep force generator employing the elliptical regularisation. The results significantly differ, especially in predicted creepages, because the elliptical regularisation neglects generation of the longitudinal creep force by spin creepage.     

基于小波和粒子群算法的HEV行驶状况辨识方法研究

针对混合动力汽车(HEV)行驶状况(道路坡度和整车载荷)变化难以有效识别,导致驱动系统控制策略不能有效满足驾驶员意图问题,以混联式HEV为研究对象,提出了基于小波滤波和粒子群算法的HEV行驶状况辨识方法。首先建立了汽车行驶状况辨识模型,采用最小二乘法确立了优化目标函数,其次研究了基于小波滤波和粒子群算法的HEV行驶状况辨识原理,最后进行了行驶状况粒子群智能算法辨识试验。在采集实车数据的基础上,对实车数据进行小波滤波,并运用行驶状况辨识方法对道路坡度和整车载荷进行了辨识,并对辨识结果进行小波滤波,结果表明,试验工况下整车载荷辨识的相对误差绝对平均值为2.71%,道路坡度辨识的相对误差绝对平均值为3.85%,验证了所提出方法的有效性。     

“学-导多元互动”教学模式对高校艺术设计教育的启示——以视觉传达设计教学为例

“学-导多元互动”教学模式是依据相关教育理论、教育观念以及结合现代远程开放教育发展的要求和实践而形成的重在体现以人为本,真正做到“以学习者为中心”,为学习者提供多元的服务,满足学习者的学习需要和求知愿望,构建终身学习体系和学习型社会的教育思想的教学模式。文章以视觉传达设计教学为例,从“学-导多元互动”教学模式的内涵、教学效果及对高校艺术设计教育的启示三个方面加以阐述,希望对于高校艺术设计教育教学模式的改革起到一些借鉴作用。