Electric vehicle charging station locations: Elastic demand,station congestion,and network equilibrium

Battery-only electric vehicles (BEVs) generally offer better air quality through lowered emissions, along with energy savings and security. The issue of long-duration battery charging makes charging-station placement and design key for BEV adoption rates. This work uses genetic algorithms to identify profit-maximizing station placement and design details, with applications that reflect the costs of installing, operating, and maintaining service equipment, including land acquisition. Fast electric vehicle charging stations (EVCSs) are placed across a congested city's network subject to stochastic demand for charging under a user-equilibrium traffic assignment. BEV users’ station choices consider endogenously determined travel times and on-site charging queues. The model allows for congested-travel and congested-station feedback into travelers’ route choices under elastic demand and BEV owners’ station choices, as well as charging price elasticity for BEV charging users.Boston-network results suggest that EVCSs should locate mostly along major highways, which may be a common finding for other metro settings. If 10% of current EV owners seek to charge en route, a user fee of $6 for a 30-min charging session is not enough for station profitability under a 5-year time horizon in this region. However, $10 per BEV charging delivers a 5-year profit of $0.82 million, and 11 cords across 3 stations are enough to accommodate a near-term charging demand in this Boston-area application. Shorter charging sessions, higher fees, and/or allowing for more cords per site also increase profits generally, everything else constant. Power-grid and station upgrades should keep pace with demand, to maximize profits over time, and avoid on-site congestion.     

隧道爆破荷载作用下中隔壁动力响应与破坏机理研究

中隔壁结构作为隧道初期支护体系中重要的承载构件,在隧道爆破荷载作用下极易发生损伤开裂和破坏。首先依托双向八车道的港沟高速公路隧道工程,进行爆破荷载作用下中隔壁的动力损伤破坏试验,提出中隔壁支护结构的破坏形态及类型;然后利用ANSYS/LS-DYNA建立隧道爆破与中隔壁支护结构数值模型,采用流固耦合的方法模拟岩体爆破及中隔壁支护结构的动力响应,并考虑单段装药量、爆距等不同因素,研究其对中隔壁破坏模式及形态的影响。研究结果表明：隧道爆破荷载作用下中隔壁破坏形式分为背爆侧混凝土开裂剥落、中心区域混凝土震塌成洞、钢筋网及纵向连接钢筋震坏断裂、钢拱架发生扭曲变形4种类型;中隔壁支护结构在爆破应力波的作用下处于反复拉压状态,并在岩石破碎抛掷冲击的作用下发生破坏,且中隔壁支护结构中心、顶部和底部是结构最易发生损伤的部位;单段装药量和爆距的改变会对中隔壁支护结构的破坏范围和破坏程度产生影响,且结构呈现出不同的破坏形态,与现场试验结果一致;建议隧道爆破施工时爆距控制在40 cm以上,单段药量控制在7.2 kg以下,以减少对中隔壁支护结构的破坏。     

PHEV发动机驱动工况效率耦合分析与优化控制

单轴并联式混合动力系统（Parallel Hybrid Electric Vehicle,PHEV）包括电池、驱动电机、发动机、自动变速器等多个关键部件。各部件效率特性存在相互耦合的关系,要实现系统整体效率最优,需要辨明影响系统效率的控制参数,并对系统整体效率最优的控制参数进行优化。以装备无级变速器（Continuously Variable Transmission,CVT）的PHEV为研究对象,首先对系统各关键部件的效率特性进行分析,建立各关键部件效率模型,明确各部件效率与控制参数、状态参数之间的关系。在此基础上,对发动机单独驱动模式下动力传递路径中不同部件的效率耦合关系进行分析,推导出系统燃油消耗量与动力系统各状态参数、控制参数之间的函数关系。根据分析结果,选取车辆需求功率及车速为状态参数,变速器速比及发动机转矩为控制参数,以系统燃油消耗量最小为目标建立优化目标函数和约束条件,对系统优化问题进行定义。根据优化问题的特点,设计基于模拟退火的优化算法对优化问题进行求解,获取系统燃油消耗率最小时变速器目标速比和发动机目标转矩随状态参数的变化关系。建立系统仿真模型对所述优化算法进行仿真分析,并搭建混合动力试验台对优化结果进行试验验证。结果表明：无级变速器效率对系统整体效率影响较大,采用优化控制规律使发动机效率有所降低,但无级变速器效率升高更大,系统整体效率升高;在功率需求一定的循环工况下,优化控制算法比传统上仅以发动机效率最高为目标的控制算法节油1%~2%。     

用遗传算法求空间点列的最小包容球

建立了求空间点列包容球的数学模型,将求最小包容球问题转化为函数优化问题,并用遗传算法解决了函数最优解的求解问题.     

A second order volume of fluid （VOF） scheme for numerical simulation of 2-D breaking waves

Among all environmental forces acting on ocean structures and marine vessels, those resulting from wave impacts are likely to yield the highest loads. Being highly nonlinear, transient and complex, a theoretical analysis of their impact would be impossible without numerical simulations. In this paper, a pressure-split two-stage numerical algorithm is proposed based on Volume Of Fluid (VOF) methodology. The algorithm is characterized by introduction of two pressures at each half and full cycle time step, and thus it is a second-order accurate algorithm in time. A simplified second-order Godunov-type solver is used for the continuity equations. The method is applied to simulation of breaking waves in a 2-D water tank, and a qualitative comparison with experimental photo observations is made. Quite consistent results are observed between simulations and experiments. Commercially available software and Boundary Integral Method (BIM) have also been used to simulate the same problem. The results from present code and BIM are in good agreement with respect to breaking location and timing, while the results obtained from the commercial software which is only first-order accurate in time has clearly showed a temporal and spatial lag, verifying the need to use a higher order numerical scheme.     

战场抢修多目标多分队调度优化研究

基于多目标的战场抢修分队调度优化问题一直以来是装备指挥管理部门关注的问题之一.通过约束转换,确立了采用遗传算法进行多目标优化调度的模型,并详细地说明了遗传操作方法的设计,实例验证了遗传算法在多目标多分队调度问题处理过程中的有效性.     

考虑对地航速和航向的船舶典型轨迹提取方法

基于船舶自动识别系统(Automatic Identification System, AIS)数据的船舶典型轨迹挖掘需要经过两个重要步骤,一是压缩 AIS 数据,二是聚类压缩后的 AIS 数据。传统的DP(DouglasPeucker)压缩算法,只考虑船舶轨迹的压缩形状,忽视了船舶航行中其他重要信息。为解决此问题,把对地航速和航向加入到DP算法的压缩过程中。在AIS轨迹聚类方面,传统谱聚类方法只对船舶轨迹的位置进行相似性度量,没有考虑船舶轨迹的其他维度,针对此问题,提出多属性轨迹相似性度量方法。由于不同的输入参数影响着最终的聚类质量,引入Calinski-Harabasz指标评价谱聚类算法,实现聚类参数的自适应选择。利用山东威海水域的实际AIS数据进行实例研究,并与传统谱聚类算法做比较实验。实验结果表明,利用该方法提取到的典型轨迹符合真实水域的交通情况,相较于传统谱聚类方法具有更高的聚类质量。     

青藏铁路综合视频监控系统室外摄像机抖动频率特征分析

青藏铁路沿线多处区段常年多风,导致安装在铁塔高处的长焦摄像机产生抖动引起图像模糊,因此使用的长焦摄像机应具有防抖功能.而多个摄像机、镜头等生产厂家,均无法提供其电子防抖性能的具体参数指标,或无法给出光学/机械防抖性能参数指标来源.通过提出采用SURF算法提取匹配图像的特征点,介绍算法原理和算法实现过程,并开展算法验证和...     

基于模拟退火-自适应布谷鸟算法的城市公交调度优化研究

为改善城市常规公交运营效率,提出基于模拟退火-自适应布谷鸟算法的公交调度优化模型.通过结合线路实际客流数据反映的客流特征,建立考虑公交公司和乘客双方利益的公交调度优化模型;改进布谷鸟算法固定步长并加入模拟退火算法退火操作,设计模拟退火-自适应布谷鸟算法,改善寻优过程中跳出局部最优解而全局寻优的能力;以福州125路公交线...     

针对自适应巡航的驾驶人风格辨识

车辆进入自适应巡航工况下行驶时,不同风格的驾驶人会对自适应巡航控制系统(Adaptive Cruise Control,ACC)有不同的需求。文章首先通过对不同驾驶人在9种跟随试验下获取的实验数据分析,选取表征驾驶人风格的驾驶特征参数;其次对所有驾驶人驾驶特征参数利用K-mean算法聚类分析,将驾驶人三类,并利用BP神经网络建立辨识模型对驾驶人风格进行辨识。结果表明;文章提出的方法可以较高的准确率对驾驶人风格进行分类,提高自适应巡航系统适应驾驶人的能力。