针摆传动中弓背齿廓的受力分析

针对针摆传动中的高精度要求,给出了求最佳修形量的优化方法,在对齿廓修形产生的几何相对转角进行计算的基础上提出了弓背齿廓,进行了理论分析研究,并通过动态受力分析方法得到齿面接触力和接触应力.采用弓背齿廓修形方式计算结果表明,最佳弓背齿廓修形可以获得较小几何相对转角,有效减小回转误差,实现高精度传动,以适用于有高精度要求的针摆传动中.     

珠江黄埔大桥北汊桥钢主梁应力不均匀性研究

珠江黄埔大桥北汊桥主梁采用扁平钢箱梁,结合该工程,采用混合有限元方法计算钢箱梁的受力,得到钢主梁板件的应力,分析箱梁顶板和底板应力分布的不均匀性,揭示斜拉桥中扁平钢箱梁的应力分布特点。     

半刚性沥青路面面层抗车辙设计探讨

结合对部分高速公路车辙调查结果,发现中面层处于剪应力峰值区域,中面层的车辙变形对沥青路面车辙变形的影响最大,有必要采用基于抗车辙性能的试验方法进行中面层混合料的设计。比较目前常用的3种混合料设计方法,推荐SGC混合料设计方法。     

Commuting and wellbeing: a critical overview of the literature with implications for policy and future research

ABSTRACT

This review provides a critical overview of what has been learnt about commuting’s impact on subjective wellbeing (SWB). It is structured around a conceptual model which assumes commuting can affect SWB over three time horizons: (i) during the journey; (ii) immediately after the journey; and (iii) over the longer term. Our assessment of the evidence shows that mood is lower during the commute than other daily activities and stress can be induced by congestion, crowding and unpredictability. People who walk or cycle to work are generally more satisfied with their commute than those who travel by car and especially those who use public transport. Satisfaction decreases with duration of commute, regardless of mode used, and increases when travelling with company. After the journey, evidence shows that the commute experience “spills over” into how people feel and perform at work and home. However, a consistent link between commuting and life satisfaction overall has not been established. The evidence suggests that commuters are generally successful in trading off the drawbacks of longer and more arduous commute journeys against the benefits they bring in relation to overall life satisfaction, but further research is required to understand the decision making involved. The evidence review points to six areas that warrant policy action and research: (i) enhancing the commute experience; (ii) increasing commute satisfaction; (iii) reducing the impacts of long duration commutes; (iv) meeting commuter preferences; (v) recognising flexibility and constraints in commuting routines and (vi) accounting for SWB impacts of commuting in policy making and appraisal.     

发动机悬置软垫断裂过程的有限元模拟

根据最大周向拉应力准则,应用ANSYS参数化设计语言编写的宏命令程序,对发动机悬置软垫的断裂过程进行了模拟,得出了2种步长时裂纹前进的裂尖位置及相应的裂纹轨线。     

Prediction of Welding Residual Stress in 2. 25Cr-1Mo Steel Pipe

Introduction2.25Cr-1Mo-steel is widely used in thepetroleum industry and in steam power generatingof both nuclear and conventional power plants be-cause of its excellent high-temperature strength,corrosion resistibility,and resistance to high-tem-perature hydrogen attack.Because several alloy el-ements are added into2.25Cr-1Mo-steel,marten-site is prone to form after welding.It has been rec-ognized that phase transformation can radically af-fect the development of residual stresses[1-2].Inor…     

Fitness-for-purpose assessment of cracked offshore wind turbine monopile

In this paper, the procedure for flaw acceptability assessment is examined through a case study of a semi-elliptical surface crack in an offshore monopile as it grows till it forms a through thickness crack. Using the procedure prescribed in an industrial standard (BS 7910), the fracture ratio, K_r is shown to increase monotonically with increasing crack depth. The load ratio, L_r, is initially insensitive to the crack depth. However, there is a rapid increase in L_r when the crack depth to thickness ratio exceeds 80%. L_r values obtained from detailed 3D FE limit analysis using elastic-perfectly-plastic material behaviour do not exhibit the asymptotic behaviour predicted by BS 7910 as the flaw transitions from deep crack to through-thickness crack. Furthermore, K_r predicted by BS 7910 is shown to be an over-estimation for the typical dimensions of offshore monopiles. The findings suggest that a structure with a deep flaw may be identified as unacceptable based on BS 7910 when it may still possess a non-trivial amount of structural residual life. This is a concern for monopiles where crack growth as a large flaw forms a significant part of the total life.     

内压载荷下X80管道裂纹应力分布规律研究

为了研究内压作用下管道裂纹应力场分布规律,以含有表面裂纹的X80管道为研究对象,对不同形状、不同方向、不同内压、不同尺寸的含裂纹管道进行仿真分析和实验验证。结果表明:裂纹尖端处应力远大于裂纹中心应力。裂纹形状对应力影响作用较小,随着裂纹方向与管道轴向夹角增大,裂纹尖端应力先增大后减小,随着管道内压、裂纹深度、裂纹长度的增大,裂纹尖端处应力随之线性增大。其中,裂纹长度对裂纹尖端应力的影响小于管道内压和裂纹深度。     

A design method of tensile triangles and low transformation temperature weld metal for reduction of stress concentration and residual stress of welded joints

Stress concentration and residual stress have a significant influence on fatigue life of welded joints. In order to reduce the stress concentration of welded joints, a mathematical design method of tensile triangles (MTT) based on bionics was applied to weld shape design. Accordingly, the stress concentration of various weld beads in the corner boxing welded joint and the fillet welded T-joint was dissected using our in-house FEM software JWRIAN. It was found that there existed a large stress concentration in the conventional welded joints, whereas those welded joints with elongated weld bead were accompanied by a lower stress concentration, especially for elongated weld bead with MTT design. Furthermore, among the weld shapes of the corner boxing fillet welded joint, the rectangle shape of weld bead had the minimum stress concentration factor (1.05). For the fillet welded T-joint with MTT design, the stress concentration of weld toe decreased dramatically with the increase of the index of designed shape, but there was a minor difference of stress concentration at weld root between the weld beads with MTT design. In addition, application of low transformation temperature (LTT) weld metal utilizing martensitic transformation to the fillet welded T-joints can produce compressive residual stress at weld toe.     

舰船加筋板局部强度评估中的总纵应力折减系数研究

舰船加强筋尺寸的合理确定一直是结构设计中的热点问题。本文综合考虑总纵弯曲应力和局部载荷的相互作用,研究加强筋的许用应力折减系数(C_s)的影响因素与合理取值方法。通过分析加强筋的力学模型、对比不同规范中的C_s取值,以及用非线性有限元软件Abaqus计算一系列加筋板模型,拟合C_s曲线并与规范对比,并验证剖面对称性和局部载荷作用方向对C_s取值的影响方式,丰富了舰船局部强度校核方法的技术背景,为板架设计、舰船三维局部校核程序开发提供借鉴。