Fitness-for-purpose assessment of cracked offshore wind turbine monopile

In this paper, the procedure for flaw acceptability assessment is examined through a case study of a semi-elliptical surface crack in an offshore monopile as it grows till it forms a through thickness crack. Using the procedure prescribed in an industrial standard (BS 7910), the fracture ratio, K_r is shown to increase monotonically with increasing crack depth. The load ratio, L_r, is initially insensitive to the crack depth. However, there is a rapid increase in L_r when the crack depth to thickness ratio exceeds 80%. L_r values obtained from detailed 3D FE limit analysis using elastic-perfectly-plastic material behaviour do not exhibit the asymptotic behaviour predicted by BS 7910 as the flaw transitions from deep crack to through-thickness crack. Furthermore, K_r predicted by BS 7910 is shown to be an over-estimation for the typical dimensions of offshore monopiles. The findings suggest that a structure with a deep flaw may be identified as unacceptable based on BS 7910 when it may still possess a non-trivial amount of structural residual life. This is a concern for monopiles where crack growth as a large flaw forms a significant part of the total life.     

挂篮底模纵梁受力简化计算方法及承重分配系数

以一桥梁施工工程实例为依托,采用有限元软件ANSYS对桥梁悬臂施工中使用的菱形挂篮进行仿真分析.提出3种简化模式计算底模纵梁的承重分配,对比发现将底模纵梁承受的外荷载简化为集中荷载,并分配至挂篮下前后横梁的方法是最优简化计算方法.在此基础上对挂篮底模纵梁承重分配系数进行优化,从而简化了繁琐的挂篮底模纵梁受力分析计算,保证了挂篮结构设计和施工的安全.     

STX1(2)型驮背多功能运输车超偏载检测标准

分析了STX₁₍₂)型驮背多功能运输车对既有超偏载检测方法和标准的适应性,提出了该车的超偏载检测方案,明确了公路货车或半挂车超偏载的检测方法及评判标准。     

内压载荷下X80管道裂纹应力分布规律研究

为了研究内压作用下管道裂纹应力场分布规律,以含有表面裂纹的X80管道为研究对象,对不同形状、不同方向、不同内压、不同尺寸的含裂纹管道进行仿真分析和实验验证。结果表明:裂纹尖端处应力远大于裂纹中心应力。裂纹形状对应力影响作用较小,随着裂纹方向与管道轴向夹角增大,裂纹尖端应力先增大后减小,随着管道内压、裂纹深度、裂纹长度的增大,裂纹尖端处应力随之线性增大。其中,裂纹长度对裂纹尖端应力的影响小于管道内压和裂纹深度。     

An improved cellular automaton with axis information for microscopic traffic simulation

Cellular Automaton (CA), an efficient dynamic modeling method that is widely used in traffic engineering, is newly introduced for traffic load modeling. This modeling method significantly addresses the modest traffic loads for long-span bridges. It does, however, require improvement to calculate precise load effects. This paper proposed an improved cellular automaton with axis information, defined as the Multi-axle Single-cell Cellular Automaton (MSCA), for the precise micro-simulation of random traffic loads on bridges. Four main ingredients of lattice, cells’ states, neighborhoods and transition rules are redefined in MSCA to generate microscopic vehicle sequences with detailed vehicle axle positions, user-defined cell sizes and time steps. The simulation methodology of MSCA is then proposed. Finally, MSCA is carefully calibrated and validated using site-specific WIM data. The results indicate: (1) the relative errors (REs) for the traffic parameters, such as volumes, speeds, weights, and headways, from MSCA are basically no more than ±10% of those of WIM data; (2) the load effects of three typical influence lines (ILs) with varied lengths of 50, 200 and 1000 m are also confidently comparable, both of which validate the rationality and precision of MSCA. Furthermore, the accurate vehicle parameters and gaps generated from MSCA can be applied not only for precise traffic loading on infrastructures but also for the accurate estimation of vehicle dynamics and safety. Hence, wide application of MSCA can potentially be expected.     

跃龙门隧道多功能钢拱架安装机快速施工配套技术

隧道施工机械化是我国隧道施工的发展方向。相较于开挖、衬砌机械化的快速发展,钢拱架安装机械化水平存在不足,长期以来较多采用人工作业,施工人员多、劳动强度大、施工效率及安装精度低,同时存在很大的安全隐患。本文通过跃龙门隧道机械化配置配套应用,分析了钢拱架安装机在机械化快速施工体系中的关键作用,并详细介绍了XZGMT411多功能钢拱架安装机相关参数、施工操作要点及注意事项。多功能钢拱架安装机的使用大幅提高了隧道施工效率及施工质量,缩短了施工工期。     

25t轴重荷载作用下隧底脱空区域受力特性分析

为了研究在役铁路隧道在通车之后隧底脱空病害的问题,采用有限元理论,建立隧道脱空区域在围岩压力与25 t轴重列车动载作用下的数值计算模型,主要研究80 cm与40 cm脱空宽度分别距隧道中心线0,80 cm与160 cm时脱空区域的受力特性。结果表明:在围岩压力下,脱空区域中线上壁和外侧顶角混凝土中产生拉应力及内侧顶角中产生压应力,其中压应力对脱空的宽度更为敏感;同时施加列车动载作用时,脱空区域上壁出现了竖向动应力与横向拉应力,得到了脱空区域力学指标的最大响应值及其出现的具体位置,宽度的增加对脱空区上壁横向拉应力更为显著,上壁横向拉应力增幅超过200%,竖向动应力增幅达50%。因此,隧底脱空区周围应力分布复杂,拉应力与压应力在脱空区域同时存在,应力突变严重,对脱空现象应及时组织处理。     

冲压机械振动对高铁桥梁及行车动力影响分析

高速铁路桥梁的平顺性和稳定性对运营列车的平稳性和安全性有很大影响。为研究冲压机械产生的外部振动激励对高铁桥梁的影响,首先通过对此机械引起的地面振动进行实测,并结合有限元分析软件,确定最大冲击荷载作用下产生的地面振动及传播至桥墩处的振动;然后通过建立列车-轨道-桥梁耦合动力学模型,将桥墩处的地面振动作为激励输入,分析列车以不同速度通过时车辆、桥梁动力学响应。结果表明:地面冲击振动有限元模型计算结果与实测结果基本相符,验证了模型的可靠性;地面振动对桥梁响应会产生一定的影响,距振源50 m处地面振动对桥梁所产生的影响较距振源80 m处(桥墩处)的大,但对运行车辆的影响很小;随着车速由250 km/h至350 km/h,车辆及桥梁各结构的动态响应均有所增大,但都未超出安全限值。因此,冲压机械冲击作用导致的地面振动对列车-轨道-桥梁系统动态服役性能影响非常有限。     

公路地基真空排水预压法探讨

真空排水预压法与堆载预压法相比具有加载快、无需堆载材料、不会失稳等优势,适用于加固软土特别是含水量较高的超软土地基。真空-堆载联合预压法的应用也越来越多。经过国内外十几年的探索,真空排水预压法日趋成熟,已经成为大面积应用的加固软土地基的行之有效的方法之一。     

马鞍山长江公路大桥钢塔线形控制技术

马鞍山长江公路大桥左汊主桥为（360＋2×1080＋360） m的三塔两跨悬索桥，中塔采用钢－混叠合、塔梁固结门式结构，下塔柱为预应力钢筋混凝土结构，上塔柱为钢结构，钢塔共分21个节段，首节采用浮吊安装，标准节段长6 m ，最大起吊重达235 t ，采用塔吊进行安装。为确保钢塔线形满足要求，对影响钢塔安装精度因素进行分析，形成以控制钢塔制造质量为核心、钢塔首节段安装精度为基础的线形控制流程，对钢塔节段进行工厂制造控制和现场安装控制。工厂制造控制包括零部件加工、块体制作、节段组拼、端面机加工、预拼装；现场安装控制包括首节段安装、标准节段安装、横梁与钢塔的连接。实践表明，该桥采用以控制钢塔制造精度为核心的钢塔线形控制技术进行钢塔架设施工，施工过程中钢塔制造精度和安装精度满足要求，实现了钢塔线形控制的目的。