新型液化天然气船液货围护系统传热模型及蒸发率计算

分析了一艘170000m3新型液化天然气船的船体结构,通过合理和必要的简化,建立了液货围护系统的传热模型。分别使用解析方法和ANSYS Fluent软件数值模拟方法计算了在不同绝热层厚度条件下的液货舱漏热量,得到不同条件下液货围护系统的温度场分布情况以及液货蒸发率。得出以下结论:综合考虑两种计算方法的计算结果,为了满足在不同工况下航行时液货的日蒸发率不能超过0.1%的要求,绝热层的设计厚度应不小于450mm。     

球扁钢肋骨三角形加热仿真研究

针对球扁钢肋骨三角形加热矫正纵向弯曲变形,利用ANSYS软件和APDL语言编写仿真程序,实现了热-结构耦合场的数值模拟,得到了加热过程中温度场和结构场的求解结果。对于不同的加热速度与气流输入量,计算了肋骨表面最高温度和高度方向的变形量,利用MATLAB曲面拟合,得到了最高温度和变形量关于加热速度和气流流量的函数。并对这两个参数进行了优化,得到了满足温度约束下变形量最大的参数组合。研究内容和结果对球扁钢肋骨三角形加热的更深入研究和现场施工提供了一定的参考和指导。     

Corrosion rate measurements in steel sheet pile walls in a marine environment

Corrosion of steel structures in the marine environment is a major problem. The deterioration of this kind of structures is costly and difficult to predict both when designing new structures and when estimating the remaining service life time for existing structures. The aim of this investigation was to find indicative values for the corrosion rate of steel sheet piles on the Swedish west coast. Such corrosion rates (mm/year) can be used both when designing new structures by oversizing the steel thickness and when estimating the bearing capacity of existing sheet pile structures. Earlier investigations on the corrosion rates along the Swedish east coast – with salinity from about 0.2% to 0.8% – are still used today as guidelines for the corrosion rate of all steel structures in the Swedish maritime environment even though the salinity on the west coast can be as high as 3.0%.Steel sheet pile wharfs located in the port of Halmstad on the Swedish west coast were inspected by ultrasonic measurements. Three wharf structures with a total length of about 700 m were inspected. None of the inspected wharfs had or have had cathodic protection. The thickness measurements of the steel sheet pile structures were performed by divers.The age of the three inspected sheet pile structures ranged from 36 to 51 years. The dimensions of the original sheet pile sections are known. One of the quay structures is located along a river. The salinity at all wharfs varied from low values at the surface to approx. 2% at the bottom (also in the river outflow).The measured average corrosion rates were in the same order as the design values in the European code. However, the results indicate increased corrosion rates about 1 m below the mean water surface and at the level of the propellers from the ships berthing the most frequented of the inspected wharfs, 3–6 m below water surface.The tolerances of steel sheet thicknesses – usually in the order of ±6% – are often neglected when investigating the remaining thickness in steel sheet piles. A simple calculation model shows that the sheet pile must be almost 50 years of age before an accurate estimation on the corrosion rate can be made, considering the tolerances, if the true original sheet pile thickness is not known.     

沥青路面运营初期平整度竣工验收标准研究

采用数理统计原理,运用SPSS软件对陕西省7条高速公路交-竣工平整度数据进行分析,得出了陕南、关中和陕北地区路面平整度衰变幅度均值分别为0.39m/km、0.28m/km和0.24m/km,这也将作为计算竣工验收推荐值的依据;再基于交-竣工平整度变化规律,建立了平整度竣工验收推荐值的计算公式:IRIju=IRIji+IRIs,可为今后平整度竣工验收标准提供有效的理论依据。     

数控铣床加工低碳钢零件的进给速度优化

论述了数控铣床加工低碳钢零件时进给速度的优化问题．在基于加工效率（可等效转化为加工工时）和加工成本目标函数的基础上，对这两个目标函数运用多目标函数理论进行综合，得到了多目标综合函数．通过计算，并综合表面粗糙度，进而得到进给速度的优化范围，并对不同转速下的进给速度给出了相应的优化参数，目的更接近生产实际，使技术人员不仅了解影响生产效率和成本的因素，也可在实际生产的应用中更加快捷和方便．     

混合动力汽车电池放电终止状态判断方法

分析比较几种判断铅酸电池放电终止状态的方法，指出这些以恒流放电特性为基础的放电终止状态判断标准不适于在变电流放电状态下工作的混合动力电动汽车用电池；U-C曲线斜率法考虑了变电流放电因素，适用于混合动力电动汽车电池管理系统对电池终止放电状态进行实时判断。     

小样本条件下混凝土强度代表值的确定

针对小样本混凝土强度代表值确定时不能利用数理统计模型的问题,引入了信息扩散原理,提出了小样本条件下混凝土强度代表值确定的实用计算模型。2个混凝土强度检测案例的计算结果表明,利用《公路工程质量检验评定标准》(JTJ071-98)进行灌注桩芯样混凝土强度代表值确定,得到的代表值保证率在95%左右波动,具有不确定性;利用《超声回弹综合法检测混凝土强度技术规程》(CECS 02:88)进行单一构件混凝土强度推定,推定值的保证率小于95%,对结构的可靠性鉴定而言是偏于不安全的,应引起试验检测人员的充分重视。     

CG125系列摩托车发动机右曲轴箱体螺孔漏气问题的探讨

通过对CG125系列摩托车发动机右曲轴箱体产品结构分析和用电脑软件演示该产品在压铸生产时的填充、收缩凝固过程,最终采用在厚大部位加镶块让缺陷转移和消除的方法,圆满地解决了该产品在压铸生产时为消除缩孔进行工艺调整时困难及产品加工后因缩孔造成的产品报废.     

整车试制阶段的电器故障诊断方法

以整车装车与跑车验证案例为背景，讨论汽车开发过程中汽车电器故障诊断的方法，阐述如何应用零部件置换原则来分析故障的重要性等级（significance）。