挂篮底模纵梁受力简化计算方法及承重分配系数

以一桥梁施工工程实例为依托,采用有限元软件ANSYS对桥梁悬臂施工中使用的菱形挂篮进行仿真分析.提出3种简化模式计算底模纵梁的承重分配,对比发现将底模纵梁承受的外荷载简化为集中荷载,并分配至挂篮下前后横梁的方法是最优简化计算方法.在此基础上对挂篮底模纵梁承重分配系数进行优化,从而简化了繁琐的挂篮底模纵梁受力分析计算,保证了挂篮结构设计和施工的安全.     

哈牡线季节性冻土接触网基础处理措施探讨

针对哈尔滨至牡丹江电气化改造工程季节性冻土分布的实际工程特点,结合季节性冻土条件下接触网基础的设计理念,对本项目选用的扩大型钢柱基础和不带扩底的拉线基础进行切向冻胀应力计算分析,并考虑影响切向冻胀力的水分、土质、负温以及基础侧表面的粗糙度等主要因素,提出了对钢柱基础采用换填加扩大型基础的处理措施,对接触网的下锚拉线基础提出了换填及加大埋深等防冻胀处理措施以抵抗季节性冻土的上拔力。     

Simulation on progressive collapse behaviour of whole ship model under extreme waves using idealized structural unit method

To ensure the safety of navigating ship, working loads and structural load-carrying capacity are two important aspects. In the present paper, a total simulation system combing load calculation and structural collapse analysis is applied to simulate progressive collapse behaviour of a single-hull Kamsarmax type bulk carrier. A three dimensional singularity distribution method is adopted to calculate pressure distribution with time history. A mixed structural model, collapse part simulated by ISUM elements and remaining part by elastic FEM elements with relative coarse mesh, is proposed for collapse analysis. Progressive collapse behaviour obtained by ISUM is good agreement with that by nonlinear software package, MARC. However, the calculation time of ISUM analysis is about 1/70 of MARC analysis. The applicability to structure system, high accuracy and sufficient efficiency of ISUM had been demonstrated.     

Closed-form multiclass cell transmission model enhanced with overtaking,lane-changing,and first-in first-out properties

A novel multiclass macroscopic model is proposed in this article. In order to enhance first-in, first-out property (FIFO) and transmission function in the multiclass traffic modeling, a new multiclass cell transmission model with FIFO property (herein called FM-CTM) is extended from its prior multiclass cell transmission model (M-CTM). Also, to enhance its analytical compactness and resultant computational convenience, FM-CTM is formulated in this paper as a set of closed-form matrix equations. The objective is to improve the accuracy of traffic state estimation by enforcing FIFO property when a fast vehicle cannot overtake a slow vehicle due to a limitation of a single-lane road. Moreover, the proposed model takes into account a different priority for vehicles of each class to move forward through congested road conditions, and that makes the flow calculation independent from their free-flow speeds. Some hypothetical and real-world freeway networks with a constant or varying number of lanes are selected to verify FM-CTM by comparing with M-CTM and the conventional CTM. Observed densities of VISSIM and real-world dataset of I-80 are selected to compare with the simulated densities from the three CTMs. The numerical results show that FM-CTM outperforms the other two models by 15% of accuracy measures in most cases. Therefore, the proposed model is expected to be well applicable to the road network with a mixed traffic and varying number of lanes.     

Vehicle kilometers traveled reduction impacts of Transit-Oriented Development: Evidence from Shanghai City

The role of residential self-selection has become a major subject in the debate over the relationships between the built environment and travel behavior. Numerous previous empirical studies on this subject have provided valuable insights into the associations between the built environment and travel behavior. However, the vast majority of the studies were conducted in North American and European cities; yet this research is still in its infancy in most developing countries, including China, where residential and transport choices are likely to be more constrained and travel-related attitudes quite different from those in the developed world. Using the data collected from 2038 residents currently living in TOD neighborhoods and non-TOD neighborhoods in Shanghai City, this paper aims to partly fill the gaps by investigating the causal relationship between the built environment and travel behavior in the Chinese context. More specifically, this paper employs Heckman’s sample selection model to examine the reduction impacts of TOD on personal vehicle kilometers traveled (VKT), controlling for self-selection. The results show that whilst the effects of residential self-selection are apparent; the built environment exhibits the most significant impacts on travel behavior, playing the dominant role. These findings produce a sound basis for local policymakers to better understand the nature and magnitude toward the impacts of the built environment on travel behavior. Providing the government department with reassurance that effective interventions and policies on land use aimed toward altering the built environment would actually lead to meaningful changes in travel behavior.     

Investigation of tailpipe and evaporative emissions from China IV and Tier 2 passenger vehicles with different gasolines

The limited understanding of vehicular emissions in China, especially evaporative emissions, is one obstacle to establishing tighter standards. To evaluate tailpipe and evaporative emissions, two typical China IV vehicles and one Tier 2 vehicle with an onboard refuelling vapour recovery (ORVR) system were selected and tested. One of the China IV vehicles was fuelled with gasoline, E10 and M15, respectively, to investigate the effect of fuel properties on vehicular emissions. For each vehicle, cold-start tailpipe emission tests were conducted first, followed by an evaporation test. Based on the emission factors and real-world vehicle activity data, the annual tailpipe and evaporative hydrocarbon (HC) emissions of each vehicle were calculated and compared. The results show that E10 and M15 significantly reduced the tailpipe CO and particle number (PN) emissions but seriously aggravated the NOx emissions, especially for M15. The hot soak losses (HSLs) and diurnal breathing losses (DBLs) were slightly impacted by the fuel properties. The annual evaporative emissions with E10 and M15 were higher than that with gasoline. The ORVR system effectively controlled the evaporative emissions, especially for DBLs. Evaporative emissions from the China IV vehicles were 1.1–1.4 times the tailpipe HC emissions. Additionally, the evaporative emission factors of the China IV vehicles were almost 50% lower than the standard (2.0 g/test), whereas their annual evaporative emissions were almost 1.8–2.8 times higher than those from the Tier 2 vehicle. Therefore, controlling evaporative emissions currently remains a great need in China, and the ORVR might be a recommended evaporative control technology.     

An improved cellular automaton with axis information for microscopic traffic simulation

Cellular Automaton (CA), an efficient dynamic modeling method that is widely used in traffic engineering, is newly introduced for traffic load modeling. This modeling method significantly addresses the modest traffic loads for long-span bridges. It does, however, require improvement to calculate precise load effects. This paper proposed an improved cellular automaton with axis information, defined as the Multi-axle Single-cell Cellular Automaton (MSCA), for the precise micro-simulation of random traffic loads on bridges. Four main ingredients of lattice, cells’ states, neighborhoods and transition rules are redefined in MSCA to generate microscopic vehicle sequences with detailed vehicle axle positions, user-defined cell sizes and time steps. The simulation methodology of MSCA is then proposed. Finally, MSCA is carefully calibrated and validated using site-specific WIM data. The results indicate: (1) the relative errors (REs) for the traffic parameters, such as volumes, speeds, weights, and headways, from MSCA are basically no more than ±10% of those of WIM data; (2) the load effects of three typical influence lines (ILs) with varied lengths of 50, 200 and 1000 m are also confidently comparable, both of which validate the rationality and precision of MSCA. Furthermore, the accurate vehicle parameters and gaps generated from MSCA can be applied not only for precise traffic loading on infrastructures but also for the accurate estimation of vehicle dynamics and safety. Hence, wide application of MSCA can potentially be expected.     

Locating emergency vehicles with an approximate queuing model and a meta-heuristic solution approach

In this paper, the location of emergency service (ES) vehicles is studied on fully connected networks. Queuing theory is utilized to obtain the performance metrics of the system. An approximate queuing model the (AQM) is proposed. For the AQM, different service rate formulations are constructed. These formulations are tested with a simulation study for different approximation levels. A mathematical model is proposed to minimize the mean response time of ES systems based on AQM. In the model, multiple vehicles are allowed at a single location. The objective function of the model has no closed form expression. A genetic algorithm is constructed to solve the model. With the help of the genetic algorithm, the effect of assigning multiple vehicles on the mean response time is reported.     

基于AR模型的并靠两船相对运动预报研究

根据两船相对运动的特点,利用两船模相对运动的测量数据,运用基于自回归模型的时间序列分析法,建立了两船相对运动的数学模型,并给出了运动姿态的预报值.通过本方法的研究,可以得到满意的相对运动预报精度,为两船补给波浪、补偿装置的开发打下了理论基础.     

大学计算机基础课程教学方式的改革与实践

随着信息技术和计算机技术迅速发展和普及，传统的计算机基础教学方式面临新的挑战。本文探讨了当前形势下大学计算机基础课程教学模式的改革方向，根据多年的教学实践，探讨了高校计算机基础教学改革模式。