双孔平行地铁顺穿桥梁对桥梁桩基础影响研究

利用有限元分析软件建立桥梁基础及双孔地铁的模型,模拟地铁盾构的施工工况。研究盾构施工前后地铁隧道、周边土体变形趋势及其对地铁顺穿桥梁的桩基础轴力、弯矩、水平变形及沉降的影响。分析结果表明:隧道施工造成隧道上部土体沉降,下部土体隆起,隧道呈现椭圆形;其顺穿桥梁桩基轴力、弯矩增加幅度较大,桩基在地铁隧道深度以上竖向沉降,在隧道深度下局部桩体隆起,桩身位移呈现“3”字形,最大位移位于隧道中心标高与隧道底标高之间。     

正确确定内燃机活塞上止点位置的热力学方法

本文详细介绍了利用局部曲线拟合的多变指数法修正示功图上止点位置的原理及特点,作者在数学处理上作了简化并编制了计算机程序及绘图程序,使之实际操作简单、便于应用。上止点位置的精度可达0.05°～0.1°CA,本文最后提供了一个实例说明该方法的具体应用。     

At-sea towing of a Mega-Float unit

A huge floating offshore platform (359m long, 60m wide, and 3m deep) was towed into the Pacific Ocean for a validation experiment for a floating airport. Full-scale measurements of towline tension and the bending strain on the upper-deck were made during towing. The measured bending moment agreed well with numerical calculation without taking the draught and towing speed into consideration.     

海浪统计资料对船舶波浪弯矩设计值的影响

对船舶,特别是超规范船舶,进行结构的直接计算设计时,首先要知道波浪弯矩设计值。 要确切地做到这一点,设计人员应合理地选择船舶航行海域的海浪长期统计资料,然后根据船 舶的装载工况和实际可能达到的航速,借用线性理论或非线性理论进行波浪弯矩的长期预报 来确定设计值。本文就一艘大型集装箱船舶,按五个典型海域的海浪统计资料,对波浪弯矩及 波浪合成弯矩作了长期预报计算,并与 ＩＡＣＳ的统一纵强度要求ＵＲ—Ｓ１１的结果作了比较和 分析,给出了对船舶结构直接计算设计有指导意义的几点结论。     

喷油泵装配线中拧紧技术的研究及应用

本论文介绍了拧紧技术的原理和方法,以及拧紧技术在喷油泵装配线中的应用.最后说明了拧紧程序在喷油泵装配线中的程序防错方法.     

A combined use of phase plane and handling diagram method to study the influence of tyre and vehicle characteristics on stability

This paper deals with in-curve vehicle lateral behaviour and is aimed to find out which vehicle physical characteristics affect significantly its stability. Two different analytical methods, one numerical (phase plane) and the other graphical (handling diagram) are discussed. The numerical model refers to the complete quadricycle, while the graphical one refers to a bicycle model. Both models take into account lateral load transfers and nonlinear Pacejka tyre–road interactions. The influence of centre of mass longitudinal position, tyre cornering stiffness and front/rear roll stiffness ratio on vehicle stability are analysed. The presented results are in good agreement with theoretical expectations about the above parameters influence, and show how some physical characteristics behave as saddle-node bifurcation parameters.     

Decoupled 3D moment control using in-wheel motors

Vehicles equipped with in-wheel motors are being studied and developed as a type of electric vehicle. Since these motors are attached to the suspension, a large vertical suspension reaction force is generated during driving. Based on this mechanism, this paper describes the development of a method for independently controlling roll and pitch as well as yaw using driving force distribution control at each wheel. It also details the theoretical calculation of a method for decoupling the dynamic motions. Finally, it describes the application of these 3D dynamic motion control methods to a test vehicle and the confirmation of the performance improvement.     

西安地铁隧道中隔墙加台阶法施工诱发的邻近桥桩变形及其控制措施

采用FLAC3D软件预测了地铁中隔墙加台阶法施工诱发的邻近桥桩变形规律,结果表明:桥桩最大水平变形和倾斜率均超出变形允许值,必须对既有桥桩采取加固措施才能确保其在地铁施工期间的安全使用。提出了采用袖阀管注浆技术控制桥桩变形的措施,并制定了现场监测方案。实测结果表明,加固措施能够确保桥桩变形在允许范围内,证明了提出的变形控制措施合理有效。     

参数化集装箱正面吊运机力矩限制方法的研究

通过对集装箱正面吊运机力矩限制数学模型的研究，提出一种新颖的参数化力矩限制方法。该方法不需关心繁杂的机器几何参数，可降低力矩限制控制系统对机械结构及有关参数的依赖程度，提高开发调试效率；可用于集装箱正面吊运机的力矩限制安全保护。     

高速铁路5×50m钢箱-混凝土连续结合梁设计研究

连续结合梁作为将钢与混凝土相组合共同参与工作的体系,受力十分复杂,应用中要确保结构具有良好的静力、动力性能。以某高速铁路5×50 m钢箱-混凝土连续结合梁为工程背景,介绍设计时对负弯矩区处理、桥面板预应力施加、混凝土徐变和活载效应、动力性能等重点问题的计算和分析,研究表明,通过调整施工顺序、采用合理的徐变及活载计算方法、底板铺设混凝土等措施,可使结构各项指标满足要求。