轨道交通信号控制系统LCC估算方法研究与应用

从产品全生命周期成本概念出发,阐述了轨道交通信号控制系统生命周期的特点和成本构成;从企业视角提出了一种轨道交通信号控制系统的LCC估算方法;通过企业项目成本管理信息化系统统计产晶LCC的各项数据,结合财务数据进行归一化估算,并定期进行回归迭代,规范化实施分析与评价,从而得出产話的LCC改进建议,为公司战略决策提供了重要参考依据。     

A real-time adaptive signal control in a connected vehicle environment

The state of the practice traffic signal control strategies mainly rely on infrastructure based vehicle detector data as the input for the control logic. The infrastructure based detectors are generally point detectors which cannot directly provide measurement of vehicle location and speed. With the advances in wireless communication technology, vehicles are able to communicate with each other and with the infrastructure in the emerging connected vehicle system. Data collected from connected vehicles provides a much more complete picture of the traffic states near an intersection and can be utilized for signal control. This paper presents a real-time adaptive signal phase allocation algorithm using connected vehicle data. The proposed algorithm optimizes the phase sequence and duration by solving a two-level optimization problem. Two objective functions are considered: minimization of total vehicle delay and minimization of queue length. Due to the low penetration rate of the connected vehicles, an algorithm that estimates the states of unequipped vehicle based on connected vehicle data is developed to construct a complete arrival table for the phase allocation algorithm. A real-world intersection is modeled in VISSIM to validate the algorithms. Results with a variety of connected vehicle market penetration rates and demand levels are compared to well-tuned fully actuated control. In general, the proposed control algorithm outperforms actuated control by reducing total delay by as much as 16.33% in a high penetration rate case and similar delay in a low penetration rate case. Different objective functions result in different behaviors of signal timing. The minimization of total vehicle delay usually generates lower total vehicle delay, while minimization of queue length serves all phases in a more balanced way.     

有轨电车交叉口交通组织及控制方案优化

有轨电车在运行过程中,易在交叉口处产生瓶颈,导致有轨电车通行速度降低、乘客舒适度下降。从有轨电车交叉口信号优先控制、现状交叉口交通管理与控制优化、公共交通组织优化、慢行交通组织优化4个方面提出了相应的优化措施。以武汉市有轨电车作为实例,提出了一系列改善措施,并利用VISSIM软件仿真模拟了实施效果,仿真结果验证了优化方案的科学性和有效性。     

铁路工程建设通用参考图《混凝土拌和站》内容要点及应用解析

混凝土拌和站是铁路建设中数量最多的大临工程之一,规划与设计是其建设的基础工作,为实现混凝土拌和站建设的规范化和标准化设计,中铁第五勘察设计院集团有限公司主持编制铁路工程建设通用参考图《混凝土拌和站》〔通临(2012)8401〕。结合相关科研课成果和工程设计实践,对通用参考图《混凝土拌和站》的编制原则、设计参数、主要内容、适用范围及注意事项进行论述,以求更好地对通用参考图宣贯和释义。     

A signal-based fault detection and classification method for heavy haul wagons

This paper proposes a signal-based fault detection and isolation (FDI) system for heavy haul wagons considering the special requirements of low cost and robustness. The sensor network of the proposed system consists of just two accelerometers mounted on the front left and rear right of the carbody. Seven fault indicators (FIs) are proposed based on the cross-correlation analyses of the sensor-collected acceleration signals. Bolster spring fault conditions are focused on in this paper, including two different levels (small faults and moderate faults) and two locations (faults in the left and right bolster springs of the first bogie). A fully detailed dynamic model of a typical 40t axle load heavy haul wagon is developed to evaluate the deterioration of dynamic behaviour under proposed fault conditions and demonstrate the detectability of the proposed FDI method. Even though the fault conditions considered in this paper did not deteriorate the wagon dynamic behaviour dramatically, the proposed FIs show great sensitivity to the bolster spring faults. The most effective and efficient FIs are chosen for fault detection and classification. Analysis results indicate that it is possible to detect changes in bolster stiffness of ±25% and identify the fault location.     

轨道交通信号设备实训课程体系的研究

高职院校以"服务为宗旨、就业为导向",与地方经济发展相结合,积极探索实践教学的方法,搭建技能型人才培养实践教学体系推动行业与自身的可持续发展。以此为出发点,建立一个完整而完善的信号设备实训课程体系,不仅有利于专业自身的发展,同时也对其他院校有着一定的借鉴意义。从而减少一些重复的工作,推动省内院校轨道信号相关专业整体水平的提升。     

定距桨直联稳频型轴带发电机系统

定距桨直联稳频型轴带发电机系统是在定距桨船舶上,通过双速比或多速比齿轮箱与自励无刷同步发电机相联接而成。其通过在主机遥控系统、主机控制与安保系统、电站管理系统、齿轮箱控制系统之间建立起复杂的逻辑关系,使相关控制、报警信号在不同系统中有序合理传递和反馈,从而达到建立一套低成本、硬件结构简单、电源品质高、能满足CCS、DNVGL等各大船级社无人机舱要求的新型定距桨直联稳频型轴带发电机系统FPP-DL-FSSG。文章介绍了该系统的作用、软硬件的构成和特点,分析了其优缺点并提出使用时的注意事项。对航运企业实行低成本运营以及节能减排具有重要意义。     

动态对动态差分相对定位方法建模与测试

揭示了传统的GNSS差分处理技术在基准站移动时所面临的问题,从差分实现的原理上首次对该问题进行了理论解释。针对这一问题建立了动态对动态差分相对定位模型,提出了测试方案并进行相应的试验验证,结果表明:所提动态对动态差分相对定位方法精度达到10cm量级,能够满足高精度动态对动态测量需求。