Point-to-point speed enforcement systems: Speed limits design criteria and analysis of drivers’ compliance

Point-to-point (P2P) speed enforcement is a relatively new approach to traffic law enforcement. Its technology allows vehicles whose average speed exceeds the speed limit over the controlled section to be fined. It therefore encourages compliance over distances longer than those where spot enforcement policies have been in place.In this paper, a procedure for consistently setting speed limits with such enforcement systems is proposed. Such a method has been applied to design the speed limits on two motorways in the district of Naples, Italy, where P2P enforcement systems became operational in 2009 and 2010. The speed limits, which were set using the Italian geometric design standard to assess vehicle stability and stopping sight distance, have been compared with those provided by using well-known international standards.The impact of the newly designed speed limits and of the P2P enforcement system on drivers’ speeding behaviour has been quantified for each highway section and vehicle type. In fact, accurate measurements of the average travel speeds of each vehicle crossing the enforced sections, before and after the activation of the system, were available. The migration from the old speed limits with spot speed enforcement to the new approach resulted in a notable increase in drivers’ compliance to the speed limits with a remarkable decrease in both the average of individual speeds and in their standard deviation.In addition, the analysis of 3 years of data shows that a gradual adaptation of drivers’ behaviour to the system took place. In particular, a decreasing compliance to the speed limits points to a non-optimal system management. Finally, the results of a revealed preference survey allowed us to make a behavioural interpretation regarding the significantly different impacts measured on the two motorways.     

邢衡高速公路邢台段桥梁设计技术要点

通过邢衡高速公路邢台段桥梁设计实践，阐述桥梁设计中的关键技术及要点，对同行具有一定的借鉴意义。     

山区漫水桥梁水毁调查分析及重建设计

重点阐述在涞水县7.21灾后公路恢复重建中，对桥梁水毁状况的调查分析以及工程重建设计要点，可为相关工作提供借鉴。     

波形钢腹板连续梁桥设计和施工相关问题探讨

大跨度波形钢腹板梁桥是一种新型桥梁结构,因其采用波形钢腹板替代混凝土腹板,相比传统的预应力混凝土连续梁桥,具有轻型、经济等诸多方面的特点。以前山河波形钢腹板连续梁桥为背景,针对设计和施工中的诸如内衬砼、剪力键、横隔板等相关问题进行了分析探讨。     

汕头苏埃隧道方案设计关键技术研究

根据汕头苏埃隧道的建设条件,对工程方案设计中的几个技术难点进行研究,并提出解决方案。通过采用"多级分流"理念,实现隧道与北岸4条城市主干道的交通衔接;选择"抛石+排水板"方案解决海域深厚淤泥地层中的围堰设计;8度高烈度震区选择合理的抗震减震措施解决隧道结构抗震;采取双道密封垫和加大密封垫断面的防水设计,满足地震时管片接缝张开量大的防水要求;针对复杂地层,对盾构选型和配置提出建议;对海底凸起进入隧道内的硬岩进行爆破预处理,以降低盾构施工风险。     

我国城市防洪排涝地下深隧规划设计与施工方法

为了建设符合中国国情的地下排水深隧,解决城市内涝问题,消除"城市看海"现象,采用调研分析的研究方法,通过调研国外城市排水深隧建设的成功案例,借鉴成熟经验并结合我国国情探索出我国城市排水深隧在规划设计、施工技术等方面的建设模式。主要结论如下:1)深隧规划必须坚持雨污分流原则,防涝标准应设为百年一遇;2)深隧层位应建于地下30~50 m的位置,隧道管线应布设在城市易涝区,并且将修建深隧、改造浅管和清淤河道衔接起来,形成一套完整的防洪排涝系统,让深隧的作用得以充分发挥,才能解决城市内涝问题;3)排水深隧要注重防水设计,防止雨水污染地下水;4)为提高深隧的经济效益,应将深隧与地下快速路的规划结合起来,功能上多样化。     

“中—尼—印铁路通道”线路设计及建设可行性分析

随着我国"一带一路"倡议的推进,跨国运输通道的建设成为倡议实施的关键环节之一,而我国建设复杂地质条件下跨国基础设施的经验尚不丰富。"中—尼—印铁路通道"是一条途经尼泊尔,连接中国和印度2个大国的运输通道,基于实地考察,分析该通道建设的必要性及建成后的效益,对线路进行初步规划,并总结该通道建设的难点:铁路轨道坡度大;沿线区域地质构造复杂;周边基础设施落后,施工条件恶劣;大量深长隧道以及大跨径高桥梁;环境以及气候条件复杂。同时对沿线隧道以及桥梁的建设可行性进行分析,并给出施工建议:沿线隧道采用以TBM法为主、钻爆法为辅的施工方法;桥梁建设则因地制宜,根据不同区间的地质特点,采用相应的建设方法。     

Influence of AC system design on the realisation of tractive efforts by high adhesion locomotives

The main task for heavy haul railway operators is to reduce the cost of exported minerals and enhance the long-term viability of rail transport operations through increasing productivity by running longer and heavier trains. The common opinion is that this is achievable by means of implementation of high adhesion locomotives with advanced AC traction technologies. Modern AC high adhesion locomotives are very complex mechatronic systems and can be designed with two alternative traction topologies of either bogie or individual axle controls. This paper describes a modelling approach for these two types of AC traction systems with the application of an advanced co-simulation methodology, where an electrical system and a traction algorithm are modelled in Matlab/Simulink, and a mechanical system is modelled in a multibody software package. Although the paper concentrates on the analysis of the functioning for these two types of traction control systems, the choice of reference slip values also has an influence on the performance of both systems. All these design variations and issues have been simulated for various adhesion conditions at the wheel–rail interface and their influence on the high traction performance of a locomotive equipped with two three-axle bogies has been discussed.     

高压共轨高速电磁阀自升压双电源驱动方法研究

在对现有高压共轨高速电磁阀驱动电路进行分析的基础上,提出了一种基于电磁阀自身的自升压方式,一方面把高速电磁阀关闭时本身储存的电能回收到储能电容中,另一方面在两缸工作间隙利用电磁阀线圈作为升压电路电感对储能电容进行能量补充,保证储能电容上的电压达到一个稳定状态。电路在保证实现双电压快速驱动的同时,使驱动结束的能量得到有效回收,同时省去外接专用升压电路所需要的电感部件,减小了电源电路的体积和设计成本,并且电控单元印制线路板的电磁兼容性设计易于保证。应用该方法对某高压共轨部件高速电磁阀进行试验,匹配出驱动参数,并进行稳定性试验验证,结果表明该方法能够满足工程应用需求。     

重型单缸柴油机燃烧过程强化研究

在1台排量为2.8L的单缸柴油机上,通过燃烧过程不断强化,将输出功率从73kW提高到150kW。研究分为两个阶段:第一阶段通过提高进气压力、降低进气阻力、优化配气相位、优化喷油系统参数,将输出功率从73kW提高到92kW;第二阶段采用了电控单体泵供油系统,并优化喷孔参数、进一步提高进气压力、降低进气温度、提高发动机转速,将输出功率提高到150kW。放热率分析结果表明:对于高强化燃烧过程,虽然预混和扩散燃烧阶段的放热速率大幅度增加,但其放热量占总放热量的比率下降,后燃阶段的放热比率显著增加。因此加强扩散燃烧阶段的放热速率仍然是高强化燃烧过程面临的主要问题。