A combined use of phase plane and handling diagram method to study the influence of tyre and vehicle characteristics on stability

This paper deals with in-curve vehicle lateral behaviour and is aimed to find out which vehicle physical characteristics affect significantly its stability. Two different analytical methods, one numerical (phase plane) and the other graphical (handling diagram) are discussed. The numerical model refers to the complete quadricycle, while the graphical one refers to a bicycle model. Both models take into account lateral load transfers and nonlinear Pacejka tyre–road interactions. The influence of centre of mass longitudinal position, tyre cornering stiffness and front/rear roll stiffness ratio on vehicle stability are analysed. The presented results are in good agreement with theoretical expectations about the above parameters influence, and show how some physical characteristics behave as saddle-node bifurcation parameters.     

Observer-based clutch disengagement control during gear shift process of automated manual transmission

A clutch disengagement strategy is proposed for the shift control of automated manual transmissions. The control strategy is based on a drive shaft torque observer. With the estimated drive shaft torque, the clutch can be disengaged as fast as possible without large driveline oscillations, which contributes to the reduction of total shift time and shift shock. The proposed control strategy is tested on a complete powertrain simulation model. It is verified that the system is robust to the variations of driving conditions, such as vehicle mass and road grade. It is also demonstrated that the revised system with switched gain can provide satisfactory performance even under large estimation error of the engine torque.     

脉宽调制逆变器—异步电动机系统电压,电流的计算机模拟

交—直—交电压型脉宽调制逆变器是牵引领域中很有发展前途的一种逆变器。本文对该种逆变器—异步电动机系统建立了一个通用的数学模型,它具有运算速度快、精度高及对计算机内存容量要求低的特点。从原则上来说可在系统的整个调频范围内,在微型计算机上对任何稳态工况时的逆变器输出电压、电机定、转子电流的基波及谐波分量进行分析,从而为该种系统的研制和改进提供了一个有力的工具。     

电控气缸注油器注油调频控制机理分析

为实现电控气缸注油器的注油调频控制,探究其注油调频的计算方法,提出注油调频的通用计算公式,分析该计算公式在研发电控气缸注油器注油调频机理上的适用方法。     

发动机振动信号不对称现象分析

某柴油机振动信号出现不对称现象,其最大值与最小值差异较大。该信号的频谱特性表明:在0-100 Hz频段内,存在发动机转速的2阶、4阶、6阶分量,其中2、4阶分量之间存在某种微妙的相位关系,导致其在时域叠加后出现不对称现象。本文进一步研究了2阶、4阶分量在800~3 000 r/min整个转速范围内的振动位移,发现低转速时比高转速时大87.5%以上。根据发动机力学模型认为这是由发动机倾覆力矩引起的,指明了改进方向,为该发动机的改进方案提供了检验依据。     

Flexural gravity wave generation by initial disturbances in the presence of current

The effect of uniform current on the generation of flexural gravity waves resulting from initial disturbances at a point was analyzed in two dimensions. The problem was formulated as an initial boundary value problem under the assumptions of the linearized theory of water waves. By direct application of the Laplace transform and then the Fourier transform, explicit expressions for the velocity potential and free surface elevation were obtained in integral forms; these were evaluated asymptotically for large distances and times by the application of the method of the stationary phase to obtain the far field behavior of the surface elevations in specific cases. Simple numerical computations were performed to illustrate the effect of uniform current on the surface elevation, wavelength, phase velocity, and group velocity of the flexural gravity waves and on the far field behavior of the progressive waves in two different cases, namely, when there is an initial depression concentrated at the origin and an initial impulse concentrated at the origin.     

基于解调技术的喷泵空化特征提取方法研究

通过对喷水推进泵实船空化测量，捕捉了喷水推进泵在不同工况下的进口水声信号和壳体振动信号，对其空化调制特征进行了研究。结果表明：①喷水推进泵的空化受其叶频及其倍叶频调制；②随着空化强度的增加，喷水推进泵的调制特征量的变化与声压规律曲线一致，即满足先上升后下降的趋势。据此，可以利用调制特征对喷水推进泵的空化进行实时监测。     

交叉口交通信号相位优化技术研究

提高通行能力，减少交通拥挤和事故，是城市交通管理的主要目的。目前解决城市平面交叉口交通流的冲突问题的主要办法是采用交通信号灯。根据交通流通过交叉口时形成的冲突点，提出相位优化原理，有助于完整地解决相位优化的网络图计算问题，为解决城市平面交叉口交通拥挤与事故提供多相位安排的理论依据。实例证明，此相位优化技术不仅具有理论价值，而且具有工程应用价值，可为城市交通实用管理提供参考。     

基于动态模量试验的沥青混合料老化性能研究

为研究沥青混合料老化过程中的动态特性,对在不同温度条件下经受不同频率的动荷载的沥青混合料在不同老化期的动态模量进行试验,分析温度和荷载频率对动态模量及相位角的影响,采用车辙因子对沥青混合料的高温稳定性进行评价,并根据时间温度等效原理建立了不同老化程度的动态模量主曲线。研究结果表明：老化沥青混合料的动态模量和相位角具有明显的温度和频率依赖性,老化使沥青混合料动态模量增大,相位角减小。动态模量主曲线研究结果表明老化使沥青混合料的动态模量在整个温度（或频率）范围内变化幅度减小。     

客运专线牵引变电所换相联接的分析研究

研究目的：电气化铁道是单相移动牵引负荷，会造成电力系统三相负荷的不平衡，对不平衡产生的负序电流问题，需探讨减小负序电流的措施，尽量减小牵引负荷对电力系统的负序影响。研究结论：电气化铁道牵引变电所普遍采用换相联接的供电方式——轮换接人电力系统中的不同相。本文对电气化铁道牵引变电所采用单相结线、单相V，v结线、三相V，v结线、三相YN，d11结线、三相一两相平衡结线、三相V，X结线等牵引变压器的端子标志及联接进行了论述和总结，对牵引变电所采用各种牵引变压器的换相联接方式进行了分析研究，提出了客运专线采用AT供电方式时，单相或单相V，x结线的变压器端子标志、联接方案及牵引变电所换相联接的推荐方案。采用该方案可以简化牵引变电所牵引变压器一次侧高压线路的接线，避免高压侧线路出现交叉连接，同时简化了牵引变电所的平面布置，节约了投资。