城市复杂条件下过江通道桥隧方案比选研究——以宁波市四明路跨奉化江通道为例

随着城市化进程的加快,城市过江通道规划的数量越来越多。在城市建成区内,过江通道的建设条件越来越复杂,通常要处理好过江通道与交通路网、地块开发、地铁建设、河道通航等重要制约因素的之间的关系。过江通道在桥隧形式上各有利弊,以宁波市四明路跨奉化江通道为例,分别研究了桥梁、隧道过江方案的总体布置,桥隧方案与地铁的关系,通过对桥隧方案各自的优缺点进行对比分析,得出了采用桥梁方式过江为最优方案,为类似过江通道工程提供借鉴。     

汽车发动机气道内的流动模拟计算

本文介绍了汽车发动机气道内三维定常可压缩流动数值模拟的模型、算法及算例。为达到能定量分析并应用于实际设计的目的,提出了一种新的计算网格划分法,并开发了计算软件,对提高计算精度、加速收敛等关键问题进行了探索。     

水泥、乳化沥青及其用量对水泥-乳化沥青混合料性能的影响

通过对结合料为乳化沥青、水泥乳化沥青以及水泥的混合料进行马歇尔稳定度试验、劈裂强度试验以及抗压强度试验,分析了混合料为这3种结合料的情况下各自的强度增长规律和力学特性,得出了水泥乳化沥青复合结合料具有很强的优越性.     

意大利威尼斯集装箱深水港投资模式分析

全球经济回暖以及"一带一路"倡议给中资企业参与海外港口投资提供了良好契机,但海外港口投资也存在政治、经济、文化等多方面的风险。针对目前中资企业海外港口投资中存在的问题,系统分析中资企业海外港口投资模式及其优劣和适用情况,并结合国外主要港口管理模式,以意大利威尼斯集装箱深水港投资实践为典型案例,提出海外港口投资策略。     

Greenhouse gas emissions from ships in ports – Case studies in four continents

Emissions of GHG from the transport sector and how to reduce them are major challenges for policy makers. The purpose of this paper is to analyse the level of greenhouse gas (GHG) emissions from ships while in port based on annual data from Port of Gothenburg, Port of Long Beach, Port of Osaka and Sydney Ports. Port call statistics including IMO number, ship name, berth number and time spent at berth for each ship call, were provided by each participating port. The IMO numbers were used to match each port call to ship specifications from the IHS database Sea-web. All data were analysed with a model developed by the IVL Swedish Environmental Research Institute for the purpose of quantifying GHG emissions (as CO₂-equivalent) from ships in the port area. Emissions from five operational modes are summed in order to account for ship operations in the different traffic areas. The model estimates total GHG emissions of 150,000, 240,000, 97,000, and 95,000 tonnes CO₂ equivalents per year for Gothenburg, Long Beach, Osaka, and Sydney, respectively. Four important emission-reduction measures are discussed: reduced speed in fairway channels, on-shore power supply, reduced turnaround time at berth and alternative fuels. It is argued that the potential to reduce emissions in a port area depends on how often a ship revisits a port: there it in general is easier to implement measures for high-frequent liners. Ships that call 10 times or less contribute significantly to emissions in all ports.     

Experimental evaluation of Heavy Duty Vehicle speed patterns in urban and port areas and estimation of their fuel consumption and exhaust emissions

Exhaust emissions and fuel consumption of Heavy Duty Vehicles (HDVs) in urban and port areas were evaluated through a dedicated investigation. The HDV fleet composition and traffic driving from highways to the maritime port of Genoa and crossing the city were analysed. Typical urban trips linking highway exits to port gates and HDV mission profiles within the port area were defined. A validation was performed through on-board instrumentation to record HDV instantaneous speeds in urban and port zones. A statistical procedure enabled the building-up of representative speed patterns. High contrasts and specific driving conditions were observed in the port area. Representative speed profiles were then used to simulate fuel consumption and emissions for HDVs, using the Passenger car and Heavy duty Emission Model (PHEM). Complementary estimations were derived from Copert and HBEFA methodologies, allowing the comparison of different calculation approaches and scales. Finally, PHEM was implemented to assess the performances of EGR or SCR systems for NO_X reduction in urban driving and at very low speeds.The method and results of the investigation are presented. Fuel consumption and pollutant emission estimation through different methodologies are discussed, as well as the necessity of characterizing very local driving conditions for appropriate assessment.     

港口高压电缆卷筒滑环箱防凝露措施

凝露造成高压电缆卷筒滑环箱绝缘下降、箱体内元器件损坏,必须加以解决。分析凝露形成条件和造成高压电缆卷筒滑环箱故障的原因。提出温度控制法和湿度控制法两种措施。效果良好,可供参考。     

集装箱装卸桥吊具卷缆系统防失控改造

针对西门子电控系统集装箱桥吊吊具卷缆子系统在使用过程中发现的缺陷进行改造。通过修改西门子变频器参数,可有效避免桥吊吊具卷缆系统由于通信故障引发的失控,不但节约了成本,而且提高了桥吊可靠性。     

In Touch通过以太网和OMRON PLC进行连接的方法

为提高工作效率,将In Touch与Omron PLC连接。介绍了先进的人机界面软件In Touch的功能特点,In Touch与Omron PLC的几种通信方法、注意事项。该方法在散粮系统实际应用中取得了可靠的通信质量。     

大型风电过渡桩法兰制作安装工艺研究

对大型风力发电塔筒法兰的制作安装与平整度控制方法作了较为详尽的说明和分析。内容包括法兰的分片制作和整体合拢,法兰与塔筒的拼装焊接和法兰制作安装全过程对其平整度控制的相关内容等。经实践检验,证明此工艺方案具有实用、质量可靠、可操作性强和技术先进、合理等优点,并取得良好的经济效益。