基于基准有限元模型的箱梁TMD振动控制研究

针对高架桥梁结构引起的振动噪声问题,研究TMD控制箱梁结构振动的特性。为了获得精准的箱梁有限元模型,首先以铁路32 m简支箱梁桥为原型,按10:1的几何相似比设计制作简支箱梁缩尺试验模型,应用ANSYS软件建立初始动力有限元模型;对有限元模型模态分析与试验模型模态测试得到的自由模态信息进行误差分析,并采用基于灵敏度分析的模型修正技术对初始动力有限元模型弹性模量和密度进行修正,得到基准有限元模型,误差确认结果显示修正后的有限元模型更精准地反应箱梁的振动特性;进一步利用基准有限元模型,开展TMD控制简支箱梁桥振动的研究,研究结果表明TMD对于抑制桥梁竖向共振有很好的效果。     

Optimal bus fleet management strategy for emissions reduction

Transportation is a major cause for environmental degradation via exhaust emissions. For many transit-oriented metropolitan areas, bus trips often constitute a sizeable mode share. Managing the bus fleet, in particular updating buses to comply with the newer emissions standards, therefore, can have a substantial impact on transportation-induced air quality. This paper presents the approach of remaining life additional benefit–cost (RLABC) analysis for maximising the total net benefit by either early-retiring or retrofitting the current bus fleet within their lifespans. By referring to the net benefits for different bus types estimated by RLABC analysis, the most beneficial management scheme for the current bus fleet can be identified. Optimal bus fleet management (BFM) models based on the RLABC analysis for the operator and the government are developed. Then a government subsidy plan is produced to achieve win–win solutions, which will offer efficient and flexible management schemes. To illustrate the approach, the largest bus company in Hong Kong, which carries more than 23% of the total trips in Hong Kong, is taken as a case study example. Instead of adopting a fixed retirement plan, such as replacing buses at the age of 17 as is currently practised, the proposed method develops an optimal BFM scheme that progressively phases out buses or retrofits them. This study produces promising results to demonstrate the large benefit of this approach for optimal bus fleet management.     

重载货车摩擦缓冲器阻抗特性的数值模拟

为预测摩擦缓冲器的实际工作状态,从几何特征和作用原理的角度,建立详细的MT-2型缓冲器理论模型。首先,通过对缓冲器内部各摩擦元件的运动学和静力学分析,推导出缓冲器在准静态下的阻抗特性;其次,引入附加摩擦系数量化各摩擦元件之间动静态摩擦过渡时的黏滞补偿,并模拟出缓冲器在动态下的阻抗特性;最后,利用C80型货车冲击试验数据对该缓冲器的理论模型进行验证。验证结果表明:总体上,数值模拟和现场试验下的缓冲器示功曲线基本吻合,说明模型的正确性;局部上数值模拟中缓冲器从加载Ⅰ阶段过渡至加载Ⅱ阶段的突变现象在冲击试验中表现的并不明显,还有待进一步完善。     

Subjective-utility travel time budget modeling in the stochastic traffic network assignment

ABSTRACT

In this article, we propose a new model called subjective-utility travel time budget (SU-TTB) model to capture travelers' risk-averse route choices. In the travel time budget (TTB) and mean-excess travel time (METT) model, a predefined confidence level is needed to capture the risk-aversion in route choice. Due to the day-to-day route travel time variations, the exact confidence level is hard to be predicted. With the SU-TTB model, we assume travelers' confidence level belongs to an interval that they may comply with in the route choice. The two main components of SU-TTB are the utility function and the TTB model. We can show that the SU-TTB can be reduced to the TTB and METT model with proper utility function for the confidence levels. We can also prove its equivalence with our recently proposed nonlinear-expectation route travel time (NERTT) model in some cases and give some new interpretation on the NERTT with this equivalence. Finally, we formulate the SU-TTB model as a variational inequality (VI) problem to model the risk-averse user equilibrium (RAUE), termed as generalized RAUE (GRAUE). The GRAUE is solved via a heuristic gradient projection algorithm, and the model and solution algorithm are demonstrated with the Braess's traffic network and the Nguyen and Dupuis's traffic network.     

面向控制的SCR催化转化器温度模型

为了建立面向控制的SCR催化器温度模型,根据能量守恒和质量守恒方程并考虑热平衡中所涉及的换热过程不同,建立了4种SCR催化器温度的数学模型,并利用Matlab/Simulink构建图形化的计算模型。采用柴油机欧洲稳态循环(ESC)和欧洲瞬态循环(ETC)条件下的台架实测数据对模型进行检验,基于最大离散程度、拟合度和计算时间3个指标对模型进行评价和比较。结果表明,考虑催化器与废气和周围环境对流换热的温度模型具有良好的预测精度和实时性,更适合用于SCR控制策略。     

现浇预应力混凝土连续箱梁桥设计

结合某主线上一座2×30 m现浇连续预应力混凝土葙梁桥的工程实例,较详尽的介绍了该桥的设计和构造特点、上部结构计算及上下部构造设计,并结合实际针对设计时应考虑的一些因素进行了较详细的探讨.     

低温独立液舱曲面外板加工减薄量评估

基于耐低温合金材料的非线性特性,以某液化气船的低温独立液舱曲面外板加工成形过程为研究对象,研究其塑形变形过程及机理。利用ABAQUS作为计算分析工具,建立了板材原料及上、下加工模具的分析模型,给定冲压成形的时间和初始速度,并设定时间步长,考察每个时间步长的计算结果,分析了其加工过程中的弹塑性变形过程,评估了低温合金材料在加工过程中的板厚变化情况,并与实际加工测量值进行对比,验证了模型和计算分析过程的准确性。为各类低温独立液舱的设计和材料尺寸选用提供了技术支持和指导。     

侧推减阻降噪装置设计与应用探索

侧推减阻降噪装置是一种填补国内空白的特种船舶装置,此装置可针对性解决因侧推通道激发的局部紊流及气泡层影响船舶声学设备正常使用的难题,该文介绍了该装置产生的背景、预期功能、设计校核方案及船上安装使用方法,经实船验证,该装置满足母船声学设备使用要求。     

高速高频船舶舵机系统动态特性分析与研究

为船舶高速高频舵机的设计提供理论依据和技术支撑,提出了基于ADAMS、SIMULINK和AMESim的联合仿真分析的新方法,分析了船舶舵机分系统单元、非线性因素与整机系统动态特性的关系。基于ADAMS、SIMULINK和AMESim建立了船舶舵机系统联合仿真模型,从时频角度研究了变量泵、控制系统、反馈机构及传感器的特性,以及间隙、死区、泄露、灵敏度等非线性因素对舵机系统频响特性的影响关系和规律,得出了高速高频舵机设计的一般准则。     

应用三维千斤顶精确安装海上大型预制箱梁施工技术

随着码头建设逐步迈向深水化、外海化,带动上部预制梁板向大型化发展,但外海海况恶劣,传统起重船安装工艺无法保证精度。以青岛港董家口港区40万t矿石码头为例介绍外海精确安装500 t预制箱梁的整套施工工艺,主要包括采用海上塔吊、三维千斤顶与调梁扁担结合使用等。该工艺的成功实施,为海上大型预制箱梁的安装开辟了新思路。