Vibration characteristics analysis of ring-stiffened conical shells based on power series method北大核心CSCD

[目的]旨在利用解析法求解环肋圆锥壳的振动方程,对环肋圆锥壳的振动特性进行理论研究。[方法]首先,对圆锥壳分段处理,将圆锥壳沿母线方向、环向和法向的位移分别写成幂级数解的形式,并推导出幂级数项前系数的递推关系式;然后,采用梁模型模拟不同环肋数对圆锥壳振动响应特性的影响;接着,将圆锥壳分段及其环肋边界条件、位移和内力矩阵进行组装求解,得到在外部简谐力激励下圆锥壳的振动响应特性,并将所得结果与ANSYS有限元数值方法的计算结果进行对比,验证所提计算方法的有效性。最后,运用所提理论方法进行环肋圆锥壳的振动特性分析。[结果]结果显示,圆锥壳安装的环肋可明显抑制圆锥壳的振动,具体表现为响应幅值降低、固有频率升高,且在相同频段内共振峰数量减小;增大壳体厚度会引起壳体振动响应幅值降低以及固有频率升高;此外,增大半锥角、轴线长度和环肋数均可降低环肋圆锥壳的振动响应幅值。[结论]研究表明,所用方法对环肋圆锥壳振动的理论研究具有一定意义。     

上海普通干线公路与城市道路网衔接规划设计策略研究

随着上海市域外围新城、主城扩区和新市镇的发展，城乡之间的界限日趋模糊，在出行特征、出行质量要求等方面，城乡结合地区的居民与城市居民之间的差异日趋缩小，部分普通干线公路已经无法满足日益增长的城镇化交通出行需求。在新的国土空间规划及建设用地总量严控背景下，上海市城郊区域亟需优化普通干线公路与城市道路的衔接融合模式。通过梳理上海普通干线公路与城市道路的衔接现状，以问题为导向，聚焦现状衔接点位置不适宜、衔接点前后设施设计不匹配等问题，根据上海不同分区的交通特征，从布局衔接、功能衔接、标准衔接等方面讨论了普通干线公路与城市道路衔接的设计要求。     

Fatigue tests on grouted connection segment specimens in offshore wind turbine structures considering water ingression

Grouted connections (GCs) are widely used to connect superstructures and driven piles in offshore wind turbine structures. They resist fatigue loading in marine splash zones and even submerged environments. In this paper, six GC segment specimens were designed and tested under fatigue loading in both the air and water ingression conditions. The results in the air condition showed that for the specimens with lower loading ranges, the strain distributions and residual displacements stabilized after 20 thousand load cycles. These conditions persisted until the end of the test with two million cycles, with only a few tiny cracks appearing on the grout material surface. Meanwhile, wide cracks and grout material exfoliation were found in specimens with higher loading ranges. The residual displacement accumulated gradually, which eventually caused the termination of the test when it reached 5 mm after 1.3 million cycles. The results in the water ingression condition showed that the water had entered into the micro-cracks of the grout material, which severely degraded the fatigue behavior of the GC specimens. Even in lower loading ranges, specimens W-1 and W-2 only endured 0.264 million and 64 thousand load cycles before the displacement of the top clamp reached −10 mm. Compared with two specimens tested in the air, with a total displacement of less than −0.7 mm after two million load cycles, the severe deteriorating effect of water ingression on the fatigue behavior of GCs was apparent.