磁导航车体运动数字控制系统数学模型研究

探讨磁导航车体运动数字控制系统的数学模型。用实验方法建立磁导航车体运动数字控制系统典型环节的时间连续数学模型,结合车体运动机械操纵环节的传统数学模型建立整个控制系统的时间连续数学模型。利用Z变换方法把控制系统时间连续数学模型转换成离散数学模型,引入数字控制系统典型环节的数学模型,建立磁导航车体运动数字控制系统的离散数学模型。设计数字控制系统的二次型最优控制器并进行计算机仿真。仿真分析结果验证了数学模型的有效性。     

混凝土箱梁设计参数对温度效应的影响

在对水府庙混凝土箱梁桥温度场的实测和分析基础上,进行设计参数的研究,包括箱梁翼缘悬臂长度、腹板高度和桥梁轴线方位角对温度场和温度应力的影响,得到最大横向温差与（腹板高度/翼缘悬臂长度）的曲线图.     

刚构桥0#块混凝土水化热温度场改值模拟分析

文章结合罗天乐连续刚构桥施工实例，运用有限元模型对该桥0#块混凝土浇筑施工过程中的温度场变化情况进行了数值模拟分析。结果表明，0#块混凝土内部最高温度及最大内外温差计算值与实测值吻合较好。     

多年冻土区钻孔灌注桩施工过程热力特性研究

钻孔灌注桩水化热会暖化冻土引起桩基承载力下降,以桩基水化热在时间与空间上的影响效应为研究目的,结合青藏公路G214沿线查拉坪旱桥桩基观测数据,分析水化热对地温场的扰动范围以及桩周土回冻时间,给出灌注桩18 d内的养护温度。结果表明:水化热对距桩1.95 m以外地温影响微弱;144 d后桩侧温度降至0℃以下,229 d后桩侧温度低于-0.5℃;2 a后桩侧基本回冻至天然地温,此时承载力已达到设计要求。桩基混凝土养护温度前5 d在10℃以上,5~12 d在5℃以上,12~15 d为2℃以上,15~18 d仍高于0℃。通过数值仿真给出混凝土入模温度及桩基施工时间对桩周温度场的影响,模拟结果显示,该区域的灌注桩施工可以在相应规范规定范围内提高混凝土入模温度;灌注桩施工可以在冷季进行,但要做好5 m以上深度桩基混凝土的温控措施。     

超深振捣条件下混凝土墙体模板侧压力的简化计算方法

超深振捣对混凝土成品质量有害无益,研究超深振捣引起模板侧压力增大的规律,可为规避其害提供依据。为此设计4个混凝土墙体试件,实测在浇筑过程中模板侧压力的变化情况。基于振捣液化和液体压力平衡理论,建立了超深振捣情况下混凝土模板侧压力计算模型,推导了计算公式,并与实验数据进行对比验证。研究结果表明,振捣深度是影响混凝土墙体模板侧压力的重要因素,本文提出的计算模型能很好地预测墙体结构超深振捣位置的模板侧压力。     

Tuning of transfer functions for analysis of wave–ship interactions

Transfer functions are often used together with a wave spectrum for analysis of wave–ship interactions, where one application addresses the prediction of wave-induced motions or other types of global responses. This paper presents a simple and practical method which can be used to tune the transfer function of such responses to facilitate improved prediction capability. The input to the method consists of a measured response, i.e. time series sequences from a given sensor, the 2D wave spectrum characterising the seaway in which the measurements are taken, and an initial estimate of the transfer function for the response in study. The paper presents results obtained using data from an in-service container ship. The 2D wave spectra are taken from the ERA5 database, while the transfer function is computed by a simple closed-form expression. The paper shows that the application of the tuned transfer function leads to predictions which are significantly improved compared to using the transfer function without tuning.     

西南红层软岩地区铁路滑坡形成机理分析及治理措施

红层软岩地区铁路工程建设中滑坡问题突出。本文结合西南地区一铁路红层滑坡治理工程,利用该地区红层滑坡的现场调查结果,从红层软岩特性、地层岩性、地质地貌、水文地质条件、深孔位移监测数据等多方面对该地区铁路滑坡形成机理进行分析,并论述红层滑坡与一般滑坡的不同点,分析红层软岩岩体力学特性、地层主要成分以及红层软岩中的粉砂质泥岩在不同风化程度下的力学特性。根据分析结果提出治理措施,并对治理措施进行评价。总结得出地层岩性、地质水文、人为因素是导致红层滑坡病害发生的主要因素。     

基于ANN的船舶撞击高桩码头群桩损伤位置预测

本文采用有限元软件ABAQUS建立了船舶撞击高桩码头群桩的空间有限元模型。通过计算评估了撞击力、桩体刚度、撞击位置和撞击角度下对群桩结构损伤位置的影响。基于人工神经网络(ANN)方法,对不同参数组合下的群桩结构损伤位置进行了预测,并对ANN方法的可行性进行了评估。     

考虑横向漂移的船舶路径跟踪自抗扰控制

针对船舶运动系统中内部动态不确定和外部干扰等问题,进行了欠驱动船舶路径跟踪的自抗扰方法研究。利用Backstepping设计参考航向角,并通过线性扩张状态观测器对流干扰和横向运动引起的横向漂移进行估计。其次,根据自抗扰算法对航向进行控制,采用线性扩张状态观测器对外界干扰及内部不确定项进行估计。最后仿真结果表明,在风流干扰下所设计的控制器仍能使船准确地跟踪上参考路径,验证了所提控制方案的有效性。     

Comparing different contour methods with response-based methods for extreme ship response analysis

Environmental contours are often applied in probabilistic structural reliability analysis to identify extreme environmental conditions that may give rise to extreme loads and responses. They facilitate approximate long term analysis of critical structural responses in situations where computationally heavy and time-consuming response calculations makes full long-term analysis infeasible. The environmental contour method identifies extreme environmental conditions that are expected to give rise to extreme structural response of marine structures. The extreme responses can then be estimated by performing response calculations for environmental conditions along the contours.Response-based analysis is an alternative, where extreme value analysis is performed on the actual response rather than on the environmental conditions. For complex structures, this is often not practical due to computationally heavy response calculations. However, by establishing statistical emulators of the response, using machine learning techniques, one may obtain long time-series of the structural response and use this to estimate extreme responses.In this paper, various contour methods will be compared to response-based estimation of extreme vertical bending moment for a tanker. A response emulator based on Gaussian processes regression with adaptive sampling has been established based on response calculations from a hydrodynamic model. Long time-series of sea-state parameters such as significant wave height and wave period are used to construct N-year environmental contours and the extreme N-year response is estimated from numerical calculations for identified sea states. At the same time, the response emulator is applied on the time series to provide long time-series of structural response, in this case vertical bending moment of a tanker. Extreme value analysis is then performed directly on the responses to estimate the N-year extreme response. The results from either method will then be compared, and it is possible to evaluate the accuracy of the environmental contour method in estimating the response. Moreover, different contour methods will be compared.