海上风电大直径单桩基础固有频率影响因素的数值分析

针对海上风电整机结构其低阶固有频率的控制问题,基于有限元分析技术开展小直径桩土相互作用的数值模拟分析,与试验结果、API规范计算结果进行对比,验证了数值模型的适用性,分析大直径单桩结构桩内土芯、冲刷深度、表层土置换措施对整机固有频率的影响,结果表明,基于有限元实体单元计算所得一、二阶整机固有频率要明显大于传统p-y方法计算结果;桩内土芯对一、二阶整机固有频率影响很小;在一定范围内,随着泥面冲刷深度的增加,一、二阶固有频率降低不明显,认为传统p-y方法对于大直径单桩的适用性有待研究;在实际工程设计中,桩内土芯的影响可忽略;对于大直径单桩,在一定范围内可以忽略冲刷的影响。     

流线型钢箱梁涡激振动机理与气动控制措施

以某主跨390 m的独塔流线型钢箱梁斜拉桥为工程依托，采用风洞试验与计算流体动力学（Computational Fluid Dynamics，CFD）相结合的方法对流线型钢箱梁涡激振动机理与气动控制措施进行研究。首先，采用几何缩尺比为1∶30的主梁节段模型进行主梁涡振性能与气动控制措施优化研究；其次，采用CFD方法对主梁涡振响应进行流固耦合计算，将Newmark-β算法嵌入ANSYS Fluent用户自定义函数（User Defined Functions，UDFs）实现主梁结构振动响应求解，同时结合动网格技术实现主梁断面流固耦合分析；并根据判断条件来检索箱梁壁面上的网格单元，以获得主梁断面振动过程中的表面压力，然后结合主梁结构振动响应、表面压力以及流场特征等对主梁涡激振动机理进行分析。结果表明：该桥主梁原设计方案存在涡激共振现象，将梁底检修车轨道内移120 cm可有效抑制主梁涡振响应；主梁涡激振动响应的数值模拟结果与风洞试验结果吻合较好；检修车轨道内移120 cm后主要改变了箱梁下表面平均压力系数分布特性，且箱梁表面各测点脉动压力卓越频率不一致，有效减小了主梁涡激振动响应；流线型箱梁靠近迎风侧的“被动区域”对结构涡振响应贡献较小，背风侧“驱动区域”发生周期性旋涡脱落是影响流线型箱梁涡振的主要因素。     

浅埋顶管沉井周边土体的三维破坏形状及沉降研究

为研究顶管沉井及周边土体在顶进力作用下的形变范围与大小，以加固旋喷桩作为沉井周围加固体建立ABAQUS软件计算模型，并将模拟结果与工程实例、PLAXIS 3D软件所得结果进行对比分析。同时，采用广州地区花岗岩残积土进行室内沉井模型试验，并通过试验结果对数值模拟结论进行验证，得出结论如下： 1）在开挖基坑前达到设计强度的旋喷桩能有效减小基坑周边土体塌陷变形、坑底隆起。2）在施加工作顶推力下，前侧主动区首先出现贯通裂缝，竖向位移斜率增大出现明显拐点；继续增大顶推力，土体位移会急剧增大导致地表沉降严重。3）对于后背土体，在顶推力作用下，地表破裂线的切线角度从0°逐渐增大至45°+φ/2，导致破裂范围也不断扩大；达到45°+φ/2处后，继续施加顶推力会导致短轴方向破坏范围扩大的速度较长轴方向的速度更快；三维空间中被动区破坏土体在地表处产生形状为椭圆的破坏面，椭圆长轴方向为顶推轴线方向，被动破坏体呈现为牛角状椭圆楔体。     

Interactive travel choices and traffic forecast in a doubly dynamical system with user inertia and information provision

This study models the joint evolution (over calendar time) of travelers’ departure time and mode choices, and the resulting traffic dynamics in a bi-modal transportation system. Specifically, we consider that, when adjusting their departure time and mode choices, travelers can learn from their past travel experiences as well as the traffic forecasts offered by the smart transport information provider/agency. At the same time, the transport agency can learn from historical data in updating traffic forecast from day to day. In other words, this study explicitly models and analyzes the dynamic interactions between transport users and traffic information provider. Besides, the impact of user inertia is taken into account in modeling the traffic dynamics. When exploring the convergence of the proposed model to the dynamic bi-modal commuting equilibrium, we find that appropriate traffic forecast can help the system converge to the user equilibrium. It is also found that user inertia might slow down the convergence speed of the day-to-day evolution model. Extensive sensitivity analysis is conducted to account for the impacts of inaccurate parameters adopted by the transport agency.     

公路工程的水土保持生态补偿

就公路工程中所遇到的环境问题,结合设计施工中的解决办法,阐述公路工程的水土保持生态补偿,从而减小因道路施工给沿线自然地形、地貌造成的各种破坏,保护和改善当地环境,提高公路的使用效果,更好地发挥公路的各项功能。     

基于硬化泥膜的填舱换刀技术研究

为了解决砂土地层盾构刀盘换刀作业面易涌水、涌砂进而导致作业面失稳坍塌问题,采用水泥砂浆和膨润土浆液组成的混合浆液在土舱压力作用下,通过刀盘开口向砂土地层渗透,经固化后在原有稳定泥膜的基础上形成新型混合泥膜,在利用风镐清除土舱内硬化混合浆液的同时,保留刀盘前段形成的混合泥膜,即可进行盾构刀盘换刀作业。通过在广州某地铁盾构施工项目中的应用,表明本施工技术能为砂土地层盾构换刀提供高效且安全的解决方案。     

土压平衡盾构施工中泡沫改良砾砂土的试验研究

为了解决土压平衡盾构在砾砂土地层掘进过程中,土体塑流性差、刀盘及螺旋输送机磨损严重和开挖面平衡不易保持等问题,通过自制泡沫发生器发泡,对砾砂土地层的泡沫改良技术进行室内试验研究,分析气液比、含水率和泡沫掺量对塑流性的影响和改良前后土样的渗透系数的变化规律,得出泡沫发生器气液比在30∶1~55∶1、含水率为5%~12.5%、泡沫掺量为20%~40%时,土体具有较好的塑流性,泡沫的"轴承效应"和泡沫剂中表面活性剂的亲水基团与水、砾砂土颗粒形成的氢键是塑流性提高的根本原因;使用泡沫剂改良砾砂土后,渗透系数大幅降低,掺泡沫后在280 min内渗透系数随时间变化较小,能达到10~(-5)cm/s,泡沫剂溶液中高分子化合物的联结和液桥力是土样具有堵水作用的原因。     

Modelling,simulation and applications of longitudinal train dynamics

ABSTRACT

Significant developments in longitudinal train simulation and an overview of the approaches to train models and modelling vehicle force inputs are firstly presented. The most important modelling task, that of the wagon connection, consisting of energy absorption devices such as draft gears and buffers, draw gear stiffness, coupler slack and structural stiffness is then presented. Detailed attention is given to the modelling approaches for friction wedge damped and polymer draft gears. A significant issue in longitudinal train dynamics is the modelling and calculation of the input forces – the co-dimensional problem. The need to push traction performances higher has led to research and improvement in the accuracy of traction modelling which is discussed. A co-simulation method that combines longitudinal train simulation, locomotive traction control and locomotive vehicle dynamics is presented. The modelling of other forces, braking propulsion resistance, curve drag and grade forces are also discussed. As extensions to conventional longitudinal train dynamics, lateral forces and coupler impacts are examined in regards to interaction with wagon lateral and vertical dynamics. Various applications of longitudinal train dynamics are then presented. As an alternative to the tradition single wagon mass approach to longitudinal train dynamics, an example incorporating fully detailed wagon dynamics is presented for a crash analysis problem. Further applications of starting traction, air braking, distributed power, energy analysis and tippler operation are also presented.     

State estimation in roll dynamics for commercial vehicles

Accurate lateral load transfer estimation plays an important role in improving the performance of the active rollover prevention system equipped in commercial vehicles. This estimation depends on the accurate prediction of roll angles for both the sprung and the unsprung subsystems. This paper proposes a novel computational method for roll-angle estimation in commercial vehicles employing sensors which are already used in a vehicle dynamic control system without additional expensive measurement units. The estimation strategy integrates two blocks. The first block contains a sliding-mode observer which is responsible for calculating the lateral tyre forces, while in the second block, the Kalman filter estimates the roll angles of the sprung mass and those of axles in the truck. The validation is conducted through MATLAB/TruckSim co-simulation. Based on the comparison between the estimated results and the simulation results from TruckSim, it can be concluded that the proposed estimation method has a promising tracking performance with low computational cost and high convergence speed. This approach enables a low-cost solution for the rollover prevention in commercial vehicles.     

Direct yaw moment control and power consumption of in-wheel motor vehicle in steady-state turning

Driving force distribution control is one of the characteristic performance aspects of in-wheel motor vehicles and various methods have been developed to control direct yaw moment while turning. However, while these controls significantly enhance vehicle dynamic performance, the additional power required to control vehicle motion still remains to be clarified. This paper constructed new formulae of the mechanism by which direct yaw moment alters the cornering resistance and mechanical power of all wheels based on a simple bicycle model, including the electric loss of the motors and the inverters. These formulation results were validated by an actual test vehicle equipped with in-wheel motors in steady-state turning. The validated theory was also applied to a comparison of several different driving force distribution mechanisms from the standpoint of innate mechanical power.