起动机渐开线螺旋花键轴的设计及其冷滚轧技术

汽车用起动机电枢轴上的螺旋花键，已多采用冷滚轧加工的多键渐开线螺旋花键来代替铣削加工的四键或六键的矩形花键。阐述了渐开线螺旋键冷忆使用的新轧轮的特点及应用；指明了渐开线螺旋花键轴几何尺寸设计时应注意的问题。     

汽车摩托车渐开线花键内齿拉刀倒角齿的计算

对汽车摩托车的渐开线内齿花键，为避免其磕碰、消除锐边、减少毛刺、便于装配及降低噪声等，常在其小径与齿侧的齿角处倒出Ｃ×４５°的的倒棱，其拉刀必须制出倒角刀齿。对磨削和检测拉刀倒角刀齿的传统工艺方法进行了分析。介绍了倒角齿齿形半角β和倒角刀齿侧面至拉刀中心的距离的计算。     

车身外形CAGD中磨光三角域曲面的计算和应用

三角域曲面设计一直是车身表面造型的难点。本文建立了磨光型三角域自由 曲面的计算模型，开发了软件，通过实际设计实例证明该方法光顺性好，计算稳定，效率高。     

A local model for the simulation of two–dimensional spilling breaking waves

A numerical model for the simulation of two dimensional spilling breaking waves is described. It is derived from a previous model which, in turn, takes its underlying ideas from the Cointe and Tulin theory of steady breakers. With respect to the former model, the present one is local, i.e., the inception, extension, and geometry of the breakers are determined through the local shape of the water surface. The model has been implemented in a RANSE code, which was developed for the simulation of ship flows, through a modification in the boundary conditions. This yields a simple and effective way to reproduce the breakers influence on the underlying flow. The resulting code has been used to simulate the flow past a submerged hydrofoil. The numerical results are compared with those of the previous model and with the experimental data obtained by Duncan.     

船体三维网格的自动生成算法及其图形用户界面的设计

本文介绍的三维湿表面网格的自动生成算法,不但可完成型值表各站型线的等弧长插值拟合,而且能够在沿船长方向的任意位置上进行站的加密和插值,从而自动生成三维湿表面网格。该算法的实现依赖于一套完整的图、形用户界面。此界面用Ｕｎｉｘ平台的Ｍｏｔｉｆ、Ｃ和ＧＬ编制,友好灵活,方便易用。     

Fault tolerant nonlinear control with applications to an automated transit bus

This paper presents an integrated structure for a passive and active fault tolerant control (FTC) design approach in the framework of a robust nonlinear control technique called Dynamic Surface Control (DSC). As motivated by the automated vehicle application, we consider two categories of possible faults: pre-specified (a priori) and non-specified faults. It is first shown that DSC can be considered as a passive FTC approach in the sense that it gives simultaneous robust stability to a set of nonlinear systems even in the presence of model uncertainties and the pre-specified faults. Then, the non-specified fault is classified depending on the fault’s impact on the closed-loop system and isolatability from a fault detection and diagnosis (FDD) system. If a fault is both intolerable and isolatable, an active FTC approach is taken which includes FDD and controller reconfiguration. More specifically, trajectory reconfiguration is considered to accommodate the actuator fault, i.e., to compensate for the performance loss due to the fault within the framework of a switched hierarchical structure. Finally, the integrated structure for the longitudinal control of an automated transit bus is designed through the proposed method. Simulation results of the fault tolerant controller are shown for both single and multiple multiplicative faults. This controller was implemented on the California PATH transit buses in a demonstration of automated public transportation technology in San Diego, California in August of 2003.     

高速公路面层出现裂缝的原因与预防措施

通过对河北省高速公路路面屡次出现裂缝的现象进行调查分析,并结合秦皇岛市京沈高速公路大修工程的实践,综合分析了路面产生裂缝的主要原因,并提出有效防治裂缝产生的措施和建议.     

沥青混凝土热铺层厚度测量仪设计

针对在公路养护与沥青混凝土路面摊铺过程中,沥青混凝土的厚度控制对施工成本、路面平整度、路面质量及验收结果的影响,设计了一种能够精确测量沥青混凝土热铺层厚度的实用新型厚度测量仪,克服了目前公路工程施工中沥青混凝土热铺层厚度测量技术中的缺点与不足     

Assessment of the volume of fluid method for free-surface wave flow

This study was concerned with the free-surface wave flow around a surface-piercing foil. The volume of fluid method implemented in a Navier–Stokes computational fluid dynamics code was employed. Three widely used discretization schemes for the volume of fluid method were assessed for a test case that involved general ship waves, spilling breaking waves in front of the leading edge, and bubbly free surfaces in separated regions. A single computational approach was selected for the comparison, and a grid-dependence study was carried out. The computational results were validated against existing experimental data, showing good agreement. The validation results suggest that all three discretization schemes perform well, but the best and most efficient results were obtained using the high-resolution interface capturing scheme.     

Analysis on Ground Surface Deformation and Influence of Construction Parameters Caused by Two Different Shield Machines in Double-tube Tunnelling北大核心CSCD

Based on a shield-driven running tunnel project of Hangzhou Metro Line 2, this paper carries out field measuring of the ground surface deformation caused by two different shield machines in double-tube tunnelling in soft soil areas, obtains the laws of the surface deformation caused by shield-driven double-tube tunnelling and verifies the applicability of the modified Peck formula to double-tube tunnelling. The results show that in soft soil areas the impacts on ground surface deformation caused by different shield construction parameters in the previously and subsequently excavated tunnels are different, while the surface deformation changes sharply before and after the shield machine passing through the cutting face, and a rebound phenomenon occurs when the shield tail passes through the cutting face due to the influence of the grouting; The cutterhead torque of the shield machine in soft soil areas can be composed of five calculation factors, and the calculation results are in good agreement with the measured values. The larger the opening rate of the shield cutterhead is, the larger the average torque value will be, the higher the percentage of large ground loss rate will be, and the larger the maximum ground surface settlement will be; The ratio of cutterhead torque T to mucking volume per ring Q is used as the control parameter for analyzing the ground surface settlement, and a certain positive correlation between the ratio and the surface settlement value is determined, the smaller the cutterhead opening rate is, the more accurate the fitting results will be. © 2022, Editorial Office of "Modern Tunnelling Technology". All right reserved.