环氧沥青在大跨径钢桥面粘结层中的应用研究

粘结层材料和施工技术是大跨径钢桥面铺装的关键技术之一。根据某公路大桥桥面铺装粘结层的设计过程和特性，提出了环氧沥青粘结层的设计方法。     

大跨径连续刚构桥的温度效应分析

以魏家洲特大桥为例,按照我国公路桥涵设计规范、英国BS5400规范、新西兰规范确定不同的计算模式,对大跨径连续刚构桥进行温度效应分析,得出：温度应力在大跨径连续刚构桥整个桥梁设计中占有很大的比重,且采用不同的温度梯度计算模式,所得到的梁内温度应力值相差较大,甚至出现异号的温度应力.     

Fitness-for-purpose assessment of cracked offshore wind turbine monopile

In this paper, the procedure for flaw acceptability assessment is examined through a case study of a semi-elliptical surface crack in an offshore monopile as it grows till it forms a through thickness crack. Using the procedure prescribed in an industrial standard (BS 7910), the fracture ratio, K_r is shown to increase monotonically with increasing crack depth. The load ratio, L_r, is initially insensitive to the crack depth. However, there is a rapid increase in L_r when the crack depth to thickness ratio exceeds 80%. L_r values obtained from detailed 3D FE limit analysis using elastic-perfectly-plastic material behaviour do not exhibit the asymptotic behaviour predicted by BS 7910 as the flaw transitions from deep crack to through-thickness crack. Furthermore, K_r predicted by BS 7910 is shown to be an over-estimation for the typical dimensions of offshore monopiles. The findings suggest that a structure with a deep flaw may be identified as unacceptable based on BS 7910 when it may still possess a non-trivial amount of structural residual life. This is a concern for monopiles where crack growth as a large flaw forms a significant part of the total life.     

内压载荷下X80管道裂纹应力分布规律研究

为了研究内压作用下管道裂纹应力场分布规律,以含有表面裂纹的X80管道为研究对象,对不同形状、不同方向、不同内压、不同尺寸的含裂纹管道进行仿真分析和实验验证。结果表明:裂纹尖端处应力远大于裂纹中心应力。裂纹形状对应力影响作用较小,随着裂纹方向与管道轴向夹角增大,裂纹尖端应力先增大后减小,随着管道内压、裂纹深度、裂纹长度的增大,裂纹尖端处应力随之线性增大。其中,裂纹长度对裂纹尖端应力的影响小于管道内压和裂纹深度。     

A design method of tensile triangles and low transformation temperature weld metal for reduction of stress concentration and residual stress of welded joints

Stress concentration and residual stress have a significant influence on fatigue life of welded joints. In order to reduce the stress concentration of welded joints, a mathematical design method of tensile triangles (MTT) based on bionics was applied to weld shape design. Accordingly, the stress concentration of various weld beads in the corner boxing welded joint and the fillet welded T-joint was dissected using our in-house FEM software JWRIAN. It was found that there existed a large stress concentration in the conventional welded joints, whereas those welded joints with elongated weld bead were accompanied by a lower stress concentration, especially for elongated weld bead with MTT design. Furthermore, among the weld shapes of the corner boxing fillet welded joint, the rectangle shape of weld bead had the minimum stress concentration factor (1.05). For the fillet welded T-joint with MTT design, the stress concentration of weld toe decreased dramatically with the increase of the index of designed shape, but there was a minor difference of stress concentration at weld root between the weld beads with MTT design. In addition, application of low transformation temperature (LTT) weld metal utilizing martensitic transformation to the fillet welded T-joints can produce compressive residual stress at weld toe.     

舰船加筋板局部强度评估中的总纵应力折减系数研究

舰船加强筋尺寸的合理确定一直是结构设计中的热点问题。本文综合考虑总纵弯曲应力和局部载荷的相互作用,研究加强筋的许用应力折减系数(C_s)的影响因素与合理取值方法。通过分析加强筋的力学模型、对比不同规范中的C_s取值,以及用非线性有限元软件Abaqus计算一系列加筋板模型,拟合C_s曲线并与规范对比,并验证剖面对称性和局部载荷作用方向对C_s取值的影响方式,丰富了舰船局部强度校核方法的技术背景,为板架设计、舰船三维局部校核程序开发提供借鉴。     

25t轴重荷载作用下隧底脱空区域受力特性分析

为了研究在役铁路隧道在通车之后隧底脱空病害的问题,采用有限元理论,建立隧道脱空区域在围岩压力与25 t轴重列车动载作用下的数值计算模型,主要研究80 cm与40 cm脱空宽度分别距隧道中心线0,80 cm与160 cm时脱空区域的受力特性。结果表明:在围岩压力下,脱空区域中线上壁和外侧顶角混凝土中产生拉应力及内侧顶角中产生压应力,其中压应力对脱空的宽度更为敏感;同时施加列车动载作用时,脱空区域上壁出现了竖向动应力与横向拉应力,得到了脱空区域力学指标的最大响应值及其出现的具体位置,宽度的增加对脱空区上壁横向拉应力更为显著,上壁横向拉应力增幅超过200%,竖向动应力增幅达50%。因此,隧底脱空区周围应力分布复杂,拉应力与压应力在脱空区域同时存在,应力突变严重,对脱空现象应及时组织处理。     

含碎石化层的沥青加铺路面结构分析

利用ABAQUS有限元软件建立了含碎石化层的沥青加铺路面结构模型,研究土基、旧路基层与碎石化层模量以及碎石化层和加铺层厚度对含碎石化层沥青加铺层路面结构的力学响应的影响,确定碎石化模量的控制范围.结果表明,荷载作用中心点及附近一定区域,沥青加铺层层底受拉;沥青加铺层层底拉应力对土基模量、旧路基层模量、碎石化层厚度不敏感,但当碎石化层模量较小(接近300MPa)或加铺层厚(大于20cm)时层底拉应力均较大,在重载作用下更大.因此碎石化道路必须验算沥青层层底拉应力指标.为使沥青层层底拉应力峰值不至于过大甚至超过容许拉应力,使得受拉区域控制在一定范围以内,同时为降低加铺层竖向剪应力及土基顶面压应变,并达到防治反射裂缝的效果,碎石化层的模量宜控制在500～1000MPa.     

Analysis of cross effect on inherent deformation during the line heating process – Part 1 – Single crossed heating lines

This paper describes the effect of previous heating on inherent deformation by a subsequent heating line, more specifically, the case of two heating lines intersecting (crossing) each other. The paper has been divided into two parts. In the first part, the case of single crossed heating lines is studied in detail. The second part of the paper, discusses the case of more than one crossed heating lines. The novelty of the work lies in revealing the cross effect and how, factors such as, for example, the heating condition and the plate geometry, influence the resulting inherent deformation of crossed heating. In addition, relationships to easily get these influences are provided. The results are suitable for a wide range of heating conditions and plate thickness.     

横梁端部节点优化

通过有限元计算,对比几种常见的横梁端部连接方式,综合考虑结构整体强度、钢材使用量、舱室空间利用率、施工便利性等方面的影响因素,确定较优的连接过渡方式和过渡结构的参数尺寸,为船舶设计横梁端部节点形式的确定提供参考。