钢管拱吊装阶段中温度的影响分析

就缆索吊装钢管拱的施工方法，以工程实例讨论钢管拱在吊装阶段中温度对安装精度和应力测试结果的影响。     

环氧沥青在大跨径钢桥面粘结层中的应用研究

粘结层材料和施工技术是大跨径钢桥面铺装的关键技术之一。根据某公路大桥桥面铺装粘结层的设计过程和特性，提出了环氧沥青粘结层的设计方法。     

鼓式制动器摩擦副压强不均匀性分析与评价

定义了鼓式制动器摩擦片压强的两种不均匀度指数，推导了现有的不同机构型式的鼓式制动器的摩擦副压强不均匀度指数的计算公式，并分析了其变化特性。以这两种压强不均匀度指数作为新的评价指标，对各种型式的鼓式制动器进行了评价，揭示了一些型式的鼓式制动器所固有的缺点。提出了改进传统鼓式制动器的技术方向和途径。     

江苏省交通事故时间分布分析

根据江苏省有关交通事故数据,利用统计方法对交通事故发生的时间特征进行分析。通过分析交通事故年时间分布规律的波峰曲线,得出江苏省交通事故发生数量开始振荡变化,逐年上升的势头有望于近期遏制。通过分析交通事故、月、周、小时时间分布曲线,得出交通事故高峰小时出现在交通量高峰小时之后的9~12h、14~16h,两者不重合。死亡高峰时段(危险时段)多发生在18~21h的3h内。研究结论对不同时间内如何采取不同的安全对策来降低江苏省交通事故具有指导作用。     

大跨径连续刚构桥的温度效应分析

以魏家洲特大桥为例,按照我国公路桥涵设计规范、英国BS5400规范、新西兰规范确定不同的计算模式,对大跨径连续刚构桥进行温度效应分析,得出：温度应力在大跨径连续刚构桥整个桥梁设计中占有很大的比重,且采用不同的温度梯度计算模式,所得到的梁内温度应力值相差较大,甚至出现异号的温度应力.     

Fitness-for-purpose assessment of cracked offshore wind turbine monopile

In this paper, the procedure for flaw acceptability assessment is examined through a case study of a semi-elliptical surface crack in an offshore monopile as it grows till it forms a through thickness crack. Using the procedure prescribed in an industrial standard (BS 7910), the fracture ratio, K_r is shown to increase monotonically with increasing crack depth. The load ratio, L_r, is initially insensitive to the crack depth. However, there is a rapid increase in L_r when the crack depth to thickness ratio exceeds 80%. L_r values obtained from detailed 3D FE limit analysis using elastic-perfectly-plastic material behaviour do not exhibit the asymptotic behaviour predicted by BS 7910 as the flaw transitions from deep crack to through-thickness crack. Furthermore, K_r predicted by BS 7910 is shown to be an over-estimation for the typical dimensions of offshore monopiles. The findings suggest that a structure with a deep flaw may be identified as unacceptable based on BS 7910 when it may still possess a non-trivial amount of structural residual life. This is a concern for monopiles where crack growth as a large flaw forms a significant part of the total life.     

挂篮底模纵梁受力简化计算方法及承重分配系数

以一桥梁施工工程实例为依托,采用有限元软件ANSYS对桥梁悬臂施工中使用的菱形挂篮进行仿真分析.提出3种简化模式计算底模纵梁的承重分配,对比发现将底模纵梁承受的外荷载简化为集中荷载,并分配至挂篮下前后横梁的方法是最优简化计算方法.在此基础上对挂篮底模纵梁承重分配系数进行优化,从而简化了繁琐的挂篮底模纵梁受力分析计算,保证了挂篮结构设计和施工的安全.     

Simulation on progressive collapse behaviour of whole ship model under extreme waves using idealized structural unit method

To ensure the safety of navigating ship, working loads and structural load-carrying capacity are two important aspects. In the present paper, a total simulation system combing load calculation and structural collapse analysis is applied to simulate progressive collapse behaviour of a single-hull Kamsarmax type bulk carrier. A three dimensional singularity distribution method is adopted to calculate pressure distribution with time history. A mixed structural model, collapse part simulated by ISUM elements and remaining part by elastic FEM elements with relative coarse mesh, is proposed for collapse analysis. Progressive collapse behaviour obtained by ISUM is good agreement with that by nonlinear software package, MARC. However, the calculation time of ISUM analysis is about 1/70 of MARC analysis. The applicability to structure system, high accuracy and sufficient efficiency of ISUM had been demonstrated.     

内压载荷下X80管道裂纹应力分布规律研究

为了研究内压作用下管道裂纹应力场分布规律,以含有表面裂纹的X80管道为研究对象,对不同形状、不同方向、不同内压、不同尺寸的含裂纹管道进行仿真分析和实验验证。结果表明:裂纹尖端处应力远大于裂纹中心应力。裂纹形状对应力影响作用较小,随着裂纹方向与管道轴向夹角增大,裂纹尖端应力先增大后减小,随着管道内压、裂纹深度、裂纹长度的增大,裂纹尖端处应力随之线性增大。其中,裂纹长度对裂纹尖端应力的影响小于管道内压和裂纹深度。