25t轴重荷载作用下隧底脱空区域受力特性分析

为了研究在役铁路隧道在通车之后隧底脱空病害的问题,采用有限元理论,建立隧道脱空区域在围岩压力与25 t轴重列车动载作用下的数值计算模型,主要研究80 cm与40 cm脱空宽度分别距隧道中心线0,80 cm与160 cm时脱空区域的受力特性。结果表明:在围岩压力下,脱空区域中线上壁和外侧顶角混凝土中产生拉应力及内侧顶角中产生压应力,其中压应力对脱空的宽度更为敏感;同时施加列车动载作用时,脱空区域上壁出现了竖向动应力与横向拉应力,得到了脱空区域力学指标的最大响应值及其出现的具体位置,宽度的增加对脱空区上壁横向拉应力更为显著,上壁横向拉应力增幅超过200%,竖向动应力增幅达50%。因此,隧底脱空区周围应力分布复杂,拉应力与压应力在脱空区域同时存在,应力突变严重,对脱空现象应及时组织处理。     

含碎石化层的沥青加铺路面结构分析

利用ABAQUS有限元软件建立了含碎石化层的沥青加铺路面结构模型,研究土基、旧路基层与碎石化层模量以及碎石化层和加铺层厚度对含碎石化层沥青加铺层路面结构的力学响应的影响,确定碎石化模量的控制范围.结果表明,荷载作用中心点及附近一定区域,沥青加铺层层底受拉;沥青加铺层层底拉应力对土基模量、旧路基层模量、碎石化层厚度不敏感,但当碎石化层模量较小(接近300MPa)或加铺层厚(大于20cm)时层底拉应力均较大,在重载作用下更大.因此碎石化道路必须验算沥青层层底拉应力指标.为使沥青层层底拉应力峰值不至于过大甚至超过容许拉应力,使得受拉区域控制在一定范围以内,同时为降低加铺层竖向剪应力及土基顶面压应变,并达到防治反射裂缝的效果,碎石化层的模量宜控制在500～1000MPa.     

Analysis of cross effect on inherent deformation during the line heating process – Part 1 – Single crossed heating lines

This paper describes the effect of previous heating on inherent deformation by a subsequent heating line, more specifically, the case of two heating lines intersecting (crossing) each other. The paper has been divided into two parts. In the first part, the case of single crossed heating lines is studied in detail. The second part of the paper, discusses the case of more than one crossed heating lines. The novelty of the work lies in revealing the cross effect and how, factors such as, for example, the heating condition and the plate geometry, influence the resulting inherent deformation of crossed heating. In addition, relationships to easily get these influences are provided. The results are suitable for a wide range of heating conditions and plate thickness.     

粉质黏土层大直径泥水盾构掘进地层扰动分析

针对盾构机在粉质黏土层中推进引起的地层扰动进行分析尤为重要。以新建京张高铁JZSG-1标段清华园隧道2号～1号盾构区间为例,采用现场实测与数值模拟相结合的方法,研究大直径泥水平衡盾构隧道穿越粉质黏土层引起的地层扰动,得到土体横向水平位移及地表沉降的变化规律。需对横向1.5D范围内地表及建(构)筑物进行地层加固、加强监控量测;在盾构掘进过程中,应根据沉降数据实时调整盾构掘进参数及加固方案,以期更好地控制地表沉降。针对掌子面释放系数和注浆层软化模量进行参数分析数值计算,提出地表沉降的有效控制方法,在条件允许情况下适当提早管片的拼装及适当加快注浆层的硬化速度,可有效控制地表沉降。     

横梁端部节点优化

通过有限元计算,对比几种常见的横梁端部连接方式,综合考虑结构整体强度、钢材使用量、舱室空间利用率、施工便利性等方面的影响因素,确定较优的连接过渡方式和过渡结构的参数尺寸,为船舶设计横梁端部节点形式的确定提供参考。     

向量法在不规则隧道边仰坡面积计算中的应用

根据隧道边仰坡三维坐标测量数据,通过计算边仰坡斜面和投影水平面的法向量,进而计算两面之间夹角的方法,反算边仰坡斜面面积,在类似不规则隧道边仰坡等斜面面积计算中具有广泛的应用价值。     

Commuting and wellbeing: a critical overview of the literature with implications for policy and future research

ABSTRACT

This review provides a critical overview of what has been learnt about commuting’s impact on subjective wellbeing (SWB). It is structured around a conceptual model which assumes commuting can affect SWB over three time horizons: (i) during the journey; (ii) immediately after the journey; and (iii) over the longer term. Our assessment of the evidence shows that mood is lower during the commute than other daily activities and stress can be induced by congestion, crowding and unpredictability. People who walk or cycle to work are generally more satisfied with their commute than those who travel by car and especially those who use public transport. Satisfaction decreases with duration of commute, regardless of mode used, and increases when travelling with company. After the journey, evidence shows that the commute experience “spills over” into how people feel and perform at work and home. However, a consistent link between commuting and life satisfaction overall has not been established. The evidence suggests that commuters are generally successful in trading off the drawbacks of longer and more arduous commute journeys against the benefits they bring in relation to overall life satisfaction, but further research is required to understand the decision making involved. The evidence review points to six areas that warrant policy action and research: (i) enhancing the commute experience; (ii) increasing commute satisfaction; (iii) reducing the impacts of long duration commutes; (iv) meeting commuter preferences; (v) recognising flexibility and constraints in commuting routines and (vi) accounting for SWB impacts of commuting in policy making and appraisal.     

Assessment of fatigue strength of steel butt-welded joints in as-welded condition – Alternative approaches for curve fitting and mean stress effect analysis

Experimental fatigue data for butt-welded joints in as-welded condition and under constant amplitude tensile loading (secondary bending included) were analyzed using the nominal stress system and the notch stress system. Two approaches were used; a standard fitting procedure and minimization of the sum of squared perpendicular distances from a line with a fixed and free slope. In all cases, the latter method gave better agreement between the experimental and predicted fatigue life and fatigue strength. The analyses showed both with all broken specimen data included and with reduced data that the FAT225 curve, as recommended by IIW, might be too optimistic for the notch stress approach in the case of butt-welded joints in as-welded condition. It was also found that use of the local stress ratio instead of the applied stress ratio might explain many issues concerning current observations and apparent inconsistencies in reported literature.     

新建隧道下穿多座隧道施工技术

以渝黔引入贵阳枢纽铁路龙宝冲隧道下穿6座已建及在建隧道工程为例,结合现场,详细分析、介绍了下穿隧道施工方案、原则、施工方法;提出了新建铁路隧道近距离下穿隧道交叉点附近施工爆破控制、防护方案,以及新建、既有隧道的监控量测、超前地质预报、安全性评估与评价等施工技术;解决了下穿隧道施工中既保证新建隧道施工安全,又保证既有隧道不受影响的问题。     

泥浆悬浮砂粒能力分层测定试验研究

为实现泥浆悬浮砂粒能力的量化分析,提出一种分层测定方法,选取12%、15%和18%3种质量分数的试验泥浆,通过自行设计的分层取样装置进行试验研究,获取不同泥浆质量分数、沉降时间和砂粒粒径条件下的10个深度分段的砂粒质量分布,分析各参数影响下的砂粒沉降变化规律。结果表明:1)该分层测定方法可较好地获取不同深度分段的砂粒质量,弥补现有测定方法只能获取底层砂粒沉降质量的不足;2)试验所采用的3种质量分数的泥浆对0.1 mm以上粒径的砂粒悬浮能力均较差。根据砂粒沉降曲线分布特征,提出一种用于判别泥浆悬浮砂粒能力的方法,即砂粒沉降曲线越平缓,各层质量差异性越小,底层质量无明显拐点,不同沉降时间曲线越紧密,则泥浆悬浮砂粒能力越强。