钢箱梁U肋嵌补段疲劳开裂机理与养护措施研究

某大型悬索桥为主跨1650 m的两跨连续钢箱梁悬索桥,加劲梁采用扁平流线型分离式双箱。近2年在正交异性板钢箱梁顶板U肋嵌补段发现焊缝开裂状况,为研究及处治该病害,采用大型有限元程序ANAYS进行局部仿真计算,分析焊缝开裂后的应力分布规律、影响范围。结果表明:重车轮压的疲劳荷载、施工焊接质量等是嵌补段焊缝开裂的主要原因;钢箱梁顶板U肋嵌补段焊缝开裂会对邻近结构抗力产生影响,U肋嵌补段开裂使相邻U肋嵌补段焊缝应力增加11.8%,使U肋与顶板之间焊缝主拉应力增加57%,使邻近位置的横隔板弧形缺口主拉应力增加6%。根据分析结果建议尽早处治焊缝开裂问题,短期养护措施推荐在低应力区打止裂孔和设置临时支撑架,长期养护措施建议刨去已开裂焊缝后补焊、嵌补段整体切割后补焊和改用高强度螺栓连接方式。     

硫酸盐还原菌对高桩码头抗震设计的影响

国际上高震区高桩梁板码头抗震设计往往采用基于位移的抗震设计方法,且采用钢管桩结构较多,而硫酸盐还原菌(SRB)能在极短时间内对钢管桩造成严重的腐蚀,危害极大。针对SRB的腐蚀机理,提出3种主要防护措施,并对物理防护法的3种不同工程应用方案进行对比研究。结合菲律宾马尼拉某集装箱码头工程设计,采用控制变量法,对3个方案分别进行push-over推覆分析求解。计算结果表明,覆盖层保护法及钢管桩泥面处局部填充混凝土法的结构抗力较大且结构延性较好。对类似工程环境的码头结构设计具有借鉴意义。     

砂桩排水板复合排水机理研究

目前复合排水地基固结度及强度无法从理论角度进行计算和预测,给工程设计及施工带来较大不便.针对这一问题,对砂桩排水板复合排水边界条件进行合理简化,推导出复合排水理论模型;并借助有限元软件PLAXIS 3D进行分析,将PLAXIS 3D计算结果与理论结果进行对比,并给出排水体控制区域不规则修正系数a的建议值.结果表明,理论模型计算结果与数值模拟结果相吻合;在砂桩间距大于3 m时,a值建议取1. 20～1. 35,当砂桩间距小于3 m时,a值建议取1. 35～1. 50.     

浅埋暗挖地铁隧道施工监测方法

文章以重庆市地铁一号线大坪车站临时施工便道为例,对在浅埋、软岩条件下既有隧道拆除采用工字钢支顶、风镐破岩,新建隧道采用台阶法环形开挖预留核心土、人工非爆破开挖的施工方法,通过现场监控量测,得出最大地表沉降仅为3.82mm,表明采用合理的施工方法可以减少地表沉降。     

基于湿度应力场理论的膨胀土边坡稳定分析

边坡土体中的膨胀力是导致膨胀土边坡失稳的主要原因之一。文章基于湿度应力场理论,采用ANSYS软件的热传导分析功能模拟分析边坡的降雨入渗以及膨胀变形,并采用有限元强度折减法对不同条件下边坡安全系数进行计算,分析了膨胀土边坡稳定规律,为膨胀土边坡处治提供理论依据。     

板裂围岩结构弯曲失稳分析

文章分析了板裂结构地质背景及板裂介质岩体特征,研究了板裂围岩破坏模式及力学机理,并结合工程实例,利用随机有限元模型对板裂结构屈曲破坏进行分析。     

固结黏土地层盾构直接破除排水板关键技术研究

宁波地铁5号线1期下穿高速公路路基时存在68°斜交长40 m的含塑料排水板的固结黏土地层,为研究盾构直接通过可行性、刀具选型、施工参数优化等问题,利用TBM掘进模态综合试验平台,进行了不同类型刀具、不同掘进参数的固结黏土地层排水板破除试验。研究表明： 对于含排水板的固结黏土地层,在合理选择刀具、盾构参数并优化掘进参数情况下,盾构法施工直接破除基本可行,试验为宁波地铁工程建设提供了依据,也可为类似工程设计及施工提供参考。     

不同冷却方式对大尺寸钢板感应加热成形的影响

为有效解决船用中厚钢板复杂曲面加工问题,研究空气冷却(空冷)、正面水冷和反面水冷方式对大尺寸钢板弯曲成形的影响因素。首先采用COMSOL Multiphysics仿真平台模拟电磁感应加热和冷却变形多物理场同步耦合过程,然后分析各种因素对大尺寸钢板弯曲成形的影响,最后通过试验验证有限元模型的可靠性,并对感应加热弯曲成形效果进行评估。结果表明:相对于水冷,空气冷却对钢板Y向位移改变效果显著;相对于空气冷却,水冷对钢板角位移的改变影响明显;当频率为50 k Hz时,电流频率对表面温度和角位移影响显著;当钢板长宽比不小于1∶2时,Y向位移的增加比较显著;当长宽比约为1∶1时,角位移的改变比较明显。     

Mechanism of Tunnel Water Inflow Caused by Bending Failure of a Waterproof Dike Based on a Circular Thin Plate Mechanical Model北大核心CSCD

Water bursts during tunnel construction endanger construction, and it is therefore necessary to reserve a waterproof dike with the required thickness to avoid water bursts and to take reinforcement of the dike and treatment of the structure liable to trigger a water burst. Using the water burst at K5+398 of the Mingyueshan tunnel of the Shanghai-Chengdu expressway as an example, and considering the type of tunnel section and the upright mudstone of the dike, the waterproof dike at the work face is simplified as a round thin plate. A formula for the calculation of a minimum safety thickness for the critical waterproof dike is deduced by analyzing the force applied on the water-proof dike, and the minimum safety thickness for the water burst section at K5+398 of the Mingyueshan tunnel is cal-culated. The numerical simulation analysis demonstrates the critical thickness of waterproof dike at K5+398 of the Mingyueshan tunnel is 1.4-1.55 m, and the calculated water inflow and water burst basically agree with the actual condition. © 2018, Editorial Office of "Modern Tunnelling Technology". All right reserved.     

Experimental Study on Mechanical Behaviors of Prefabricated Column-Base Joint with Grouted Sleeves Connecting Longitudinal Reinforcements in Tunnels北大核心CSCD

In recent years, large shield tunnels with internal double-decked lanes have been developing rapidly in the field of highway tunnels, and prefabricated elements are increasingly adopted in internal structure. Based on the columns-base joint in Zhuguanglu tunnel, which is under construction, 2 full-scale specimens are designed for the quasi-static test, one specimen is connected with grout sleeve splicing and the other is cast in place. The test results show that: the bearing capacity of specimen with grout sleeve splicing is equal to that of cast-in-situ specimen, but its ductility and energy dissipation capacity are worse than that of the cast-in-situ specimen. And for the specimen with grout sleeve splicing, there exists crack concentration on the area above the sleeve. The crack width is too larger in this area. © 2018, Editorial Office of "Modern Tunnelling Technology". All right reserved.