阳安二线膨胀土填料改良研究

拟建阳安二线沿线膨胀土广泛分布,膨胀土不能直接作为路基填料,如果选取合格填料,运距较远、投资大,而且挖方地段的膨胀土又得弃掉、占地多,极不经济。通过选取现场两处代表性取土场取样,生石灰粉作添加剂,按4%、6%、8%、10%四个级别的掺入比做室内改良试验,试验表明:生石灰掺入比大于4%改良后,能达到消除膨胀性的目的,改良土有较好的水稳性和较高的强度,能满足设计要求;改良土较原膨胀土有较高的抗压强度和剪切强度,且随生石灰的掺入比增加而增大;得出了路基不同部位、不同膨胀级别膨胀土的生石灰粉掺入比,为阳安二线路基填料设计提供了理论依据。     

H型钢接触网支柱在风荷载作用下的疲劳性能分析

H型钢接触网支柱在高速铁路中得到广泛使用,直接影响铁路接触网系统安全。长期处于风荷载作用下,H型钢接触网支柱存在疲劳问题。通过建立数值计算模型,应用热点应力的表面外推法,对H型钢接触网支柱柱脚焊缝在风荷载作用下的疲劳性能进行分析。以兰新高铁H型钢接触网支柱为例,依据热点应力-寿命曲线,计算支柱焊缝的疲劳寿命。分析结果表明:其他条件不变的情况下,改变型钢规格和柱高,热点位置不发生变化;随着支柱高度增加,疲劳寿命降低21%左右;随着型钢截面的增大,疲劳寿命增加23%左右。     

土体中应力分布基本规律的探讨

基于土体的颗粒结构和只有颗粒接触传递应力的特性，对不同姿态颗粒接触中应力传递的机理分析，揭示了土体在相对静态下存在主动力的应力扩散效应和强被动力的应力集中效应，及其形成的土体中应力分布基本规律。主动力的应力场是以其所在土层的应力扩散角θ向外扩散的园锥形应力范围，在应力场内应力扩散分布，主应力方向不变，且伴有与之垂直的法向应力，应力分布均衡了应力场内颗粒和支承面的位移趋势。强被动力的支承面上存在以θ角向外扩散倒锥台形的应力平衡范围，在此范围内反向应力集中作用到强支承面，强支承面主导了其所在应力场的应力分布。土拱效应是应力集中效应的衍生效应，是相邻的同向强支承反力的应力平衡范围发生重迭时产生的现象。     

预应力混凝土槽形梁静力行为研究

为了解槽形梁静力行为,进行了一片预制预应力混凝土槽形梁的模型试验,分别考虑跨中最大弯矩及梁端最大剪力两种荷载工况对试验模型进行加载,测试了试验模型的控制断面的应力、变形.并采用非线性有限元分析方法对槽形梁的力学特性进行了研究.试验和研究得到了如下结论:该槽形梁的剪力滞效应较为突出,具有明显的开口薄壁杆件特征,底板的空间板效应明显,在设计荷载作用下结构处于线弹性状态,具有一定的安全储备.     

120阀试验过程的计算机仿真——紧急阀模型及仿真结果

建立了１２０紧急阀和试验台计算仿真模型，仿真了１２０紧急阀在试验台上的试验过程，结果表明：该模型能很好的仿真１２０阀在试验台上紧急阀试验，利用模型预测了试验台管径变化对紧急阀试验性能的影响，计算发现：管径主要影响紧急灵敏度和列车管排气时间。压力表安装位置分析表明：对于气体流速较快工况，测量结果与压力表的位置相关性较大，需要慎性确定压力表位置。该工作为试验台设计、试验规范制定和１２０紧急阀性能改进提     

橡胶沥青性能影响因素的试验研究

为了正确控制橡胶沥青工艺,采用不同胶粉种类、胶粉细度、拌和温度、基质沥青类型等制备橡胶沥青,进行针入度、软化点、弹性恢复以及SHRP等试验,分别测试橡胶沥青的高温性能、低温性能、抗老化性能等,研究各因素对橡胶沥青性能的影响,得出20目橡胶粉掺量以16%~18%较为合适的结果。     

Dynamic model for ride comfort evaluations of the rubber-tired light rail vehicle

The dynamic model was developed to evaluate vibration accelerations and ride comforts during the running of the Korean-standardised rubber-tired light rail vehicle. Ride comfort indexes were analysed and tested in accordance with UIC 513R by using the dynamic model and the actual vehicle in the test track. Based on the comparisons between analysis results and test results, the validity of the developed dynamic model was evaluated. It was verified whether or not the developed Korean-standardised rubber-tired light rail vehicle met the specified target specification on ride comfort. In addition, the influence of the wearing of guide wheels on ride comfort was estimated.     

Indirect method for wheel–rail force measurement and derailment evaluation

Wheel set flange derailment criteria for railway vehicles are derived and the influence of wheel–rail contact parameters is studied. An indirect method for wheel–rail force measurement based on these derailment evaluation criteria is proposed. Laboratory tests for the calibration of strain–force devices on the bearing box are carried out to determine the relationship between the applied force and the measured strain. The simulation package, SIMPACK, is used to develop a passenger car model to generate wheel–rail forces and vibration signals. Different cases are considered in this model to provide an accurate validation of the identified wheel–rail forces. A feasibility test is conducted in the Beijing Loop test line using a passenger car equipped with a set of strain gauges on the wheel set. The comparison of the force time history applied to the instrumented wheel set and that obtained using the indirect method is presented.     

某出口米轨动车组(Tc车)车体设计及试验对比研究

介绍了使用大型通用计算机辅助工程软件ANSYS和有限元方法,对某出口米轨动车组(Tc车)进行了分析计算的过程,并通过实际物理样机试验数据与计算数据的比对,分析车身强度的可靠性。     

Non-fragile multi-objective static output feedback control of vehicle active suspension with time-delay

This paper presents an approach to design a delay-dependent non-fragile H_∞/L₂–L_∞ static output feedback (SOF) controller for active suspension with input time-delay. The control problem of quarter-car active suspension with actuator time-delay is formulated to a H_∞/L₂–L_∞ control problem. By employing a delay-dependent Lyapunov function, new existence conditions of delay-dependent non-fragile SOF H_∞ controller and L₂–L_∞ controller are derived, respectively, in terms of the feasibility of bilinear matrix inequalities (BMIs). Then, a procedure based on linear matrix inequality optimisation and a hybrid algorithm of the particle swarm optimisation and differential evolution is used to solve an optimisation problem with BMI constraints. Design and simulation results of non-fragile H_∞/L₂–L_∞ controller for active suspension show that the designed controller not only can achieve the optimal performance and stability of the closed-loop system in spite of the existence of the actuator time-delay, but also has significantly improved the non-fragility characteristics over controller perturbations.