A comparative life-cycle energy and emissions analysis for intercity passenger transportation in the U.S. by aviation,intercity bus,and automobile

Intercity passenger trips constitute a significant source of energy consumption, greenhouse gas emissions, and criteria pollutant emissions. The most commonly used city-to-city modes in the United States include aircraft, intercity bus, and automobile. This study applies state-of-the-practice models to assess life-cycle fuel consumption and pollutant emissions for intercity trips via aircraft, intercity bus, and automobile. The analyses compare the fuel and emissions impacts of different travel mode scenarios for intercity trips ranging from 200 to 1600 km. Because these modes operate differently with respect to engine technology, fuel type, and vehicle capacity, the modeling techniques and modeling boundaries vary significantly across modes. For aviation systems, much of the energy and emissions are associated with auxiliary equipment activities, infrastructure power supply, and terminal activities, in addition to the vehicle operations between origin/destination. Furthermore, one should not ignore the embodied energy and initial emissions from the manufacturing of the vehicles, and the construction of airports, bus stations, highways and parking lots. Passenger loading factors and travel distances also significantly influence fuel and emissions results on a per-traveler basis. The results show intercity bus is generally the most fuel-efficient mode and produced the lowest per-passenger-trip emissions for the entire range of trip distances examined. Aviation is not a fuel-efficient mode for short trips (<500 km), primarily due to the large energy impacts associated with takeoff and landing, and to some extent from the emissions of ground support equipment associated with any trip distance. However, aviation is more energy efficient and produces less emissions per-passenger-trip than low-occupancy automobiles for trip distances longer than 700–800 km. This study will help inform policy makers and transportation system operators about how differently each intercity system perform across all activities, and provides a basis for future policies designed to encourage mode shifts by range of service. The estimation procedures used in this study can serve as a reference for future analyses of transportation scenarios.     

The problem of cold starts: A closer look at mobile source emissions levels

While the phenomenon of excess vehicle emissions from cold-start conditions is well known, the magnitude and duration of this phenomenon is often unclear due to the complex chemical processes involved and uncertainty in the literature on this subject. This paper synthesizes key findings regarding the influence of ambient and engine temperatures on light-duty vehicle (LDV) emissions. Existing literature, as well as analytical tools like the U.S. Environmental Protection Agency’s Motor Vehicle Emission Simulator (MOVES), indicate that while total vehicle emissions have dropped significantly in recent years, those associated with cold starts can still constitute up to 80% for some pollutant species. Starting emissions are consistently found to make up a high proportion of total transportation-related methane (CH₄), nitrous oxide (N₂O), and volatile organic compounds (VOCs). After 3–4 min of vehicle operation, both the engine coolant and the catalytic converter have generally warmed, and emissions are significantly lower. This effect lasts roughly 45 min after the engine is shut off, though the cooling rate depends greatly on the emission species and ambient temperature. Electrically (pre-)heated catalysts, using the bigger batteries available on hybrid drivetrains and plug-in vehicles, may be the most cost-effective technology to bring down a sizable share of mobile source emissions. Trip chaining (to keep engines warm) and shifting to non-motorized modes for shorter trips, where the cold start can dominate emissions, are also valuable tactics.     

Including congestion effects in urban road traffic CO2 emissions modelling: Do Local Government Authorities have the right options?

Tailpipe emissions from vehicles on urban road networks have damaging impacts, with the problem exacerbated by the common occurrence of congestion. This article focuses on carbon dioxide because it is the largest constituent of road traffic greenhouse gas emissions. Local Government Authorities (LGAs) are typically responsible for facilitating mitigation of these emissions, and critical to this task is the ability to assess the impact of transport interventions on road traffic emissions for a whole network.This article presents a contemporary review of literature concerning road traffic data and its use by LGAs in emissions models (EMs). Emphasis on the practicalities of using data readily available to LGAs to estimate network level emissions and inform effective policy is a relatively new research area, and this article summarises achievements so far. Results of the literature review indicate that readily available data are aggregated at traffic level rather than disaggregated at individual vehicle level. Hence, a hypothesis is put forward that optimal EM complexity is one using traffic variables as inputs, allowing LGAs to capture the influence of congestion whilst avoiding the complexity of detailed EMs that estimate emissions at vehicle level.Existing methodologies for estimating network emissions based on traffic variables typically have limitations. Conclusions are that LGAs do not necessarily have the right options, and that more research in this domain is required, both to quantify accuracy and to further develop EMs that explicitly include congestion, whilst remaining within LGA resource constraints.     

Did Chinese cities that implemented driving restrictions see reductions in PM10?

Imposing driving restrictions is becoming increasingly popular as a policy intended to control urban air pollution. Existing studies on this topic offer highly mixed observations, and each study tends to focus on only one city. In this paper, we used 11 Chinese cities with driving restrictions as the treatment group, and compared them to other cities that did not implement the policy. Based on a propensity score matching and difference-in-difference analysis, we found no evidence of a decrease in PM10 concentrations in cities after they implemented driving restrictions. This finding may be attributed to an increase in the number of cars in these cities after implementing driving restrictions, but we also found no evidence of an improvement in air quality for a given number of cars after implementation of the policies.     

Simulating the air quality impacts of traffic calming schemes in a dense urban neighborhood

In this study, the effects of isolated traffic calming measures and area-wide calming schemes on air quality in a dense neighborhood were estimated using a combination of microscopic traffic simulation, emission, and dispersion modeling. Results indicated that traffic calming measures did not have as large an effect on nitrogen dioxide (NO₂) concentrations as the effect observed on nitrogen oxide (NO_x) emissions. Changes in emissions resulted in highly disproportional changes in pollutant levels due to daily meteorological conditions, road geometry and orientation with respect to the wind. Average NO₂ levels increased between 0.1% and 10% with respect to the base-case while changes in NO_x emissions varied between 5% and 160%. Moreover, higher wind speeds decreased NO₂ concentrations on both sides of the roadway. Among the traffic calming measures, speed bumps produced the highest increases in NO₂ levels.     

Empirical estimation of price and income elasticities of air cargo demand: The case of Hong Kong

This paper estimates the price and income elasticities of air cargo demand and examines how they may change after the 2008 financial crisis. Using a set of time series data, we simultaneously estimate the aggregated demand and supply functions of air cargo at Hong Kong International Airport (HKIA). We find that during the entire sampling period of 2001–2013, the price elasticity for air cargo transport demand at HKIA ranges from −0.74 to −0.29, suggesting that air cargo demand in Hong Kong reacts negatively to price (as expected) but does not appear to be very sensitive to price. The income elasticity ranges from 0.29 to 1.47 and appears sensitive to seasonality adjustment approaches. However, in terms of the speed of changes, air cargo demand changes much faster than overall economy, indicating the presence of a pro-cyclical pattern of air cargo traffic with respect to the overall economy. Our analysis shows that air cargo demand becomes more sensitive to changes in both price and income after 2008.     

Airport capacity increase via the use of braking profiles

Many airports are encountering the problem of insufficient capacity, which is particularly severe in periods of increased traffic. A large number of elements influence airport capacity, but one of the most important is runway occupancy time. This time depends on many factors, including how the landing roll procedure is performed. The procedure usually does not include the objective to minimize the runway occupancy time. This paper presents an analysis which shows that the way of braking during landing roll has an essential impact on runway throughput and thus on airport capacity. For this purpose, the landing roll simulator (named ACPENSIM) was created. It uses Petri nets and is a convenient tool for dynamic analysis of aircraft movement on the runway with given input parameters and a predetermined runway exit. Simulation experiments allowed to create a set of nominal braking profiles that have different objective functions: minimizing the runway occupancy time, minimizing noise, minimizing tire wear, maximizing passenger comfort and maximizing airport capacity as a whole. The experiments show that there is great potential to increase airport capacity by optimizing the braking procedure. It has been shown that by using the proposed braking profiles it is possible to reduce the runway occupancy time even by 50%.     

A signal-based fault detection and classification method for heavy haul wagons

This paper proposes a signal-based fault detection and isolation (FDI) system for heavy haul wagons considering the special requirements of low cost and robustness. The sensor network of the proposed system consists of just two accelerometers mounted on the front left and rear right of the carbody. Seven fault indicators (FIs) are proposed based on the cross-correlation analyses of the sensor-collected acceleration signals. Bolster spring fault conditions are focused on in this paper, including two different levels (small faults and moderate faults) and two locations (faults in the left and right bolster springs of the first bogie). A fully detailed dynamic model of a typical 40t axle load heavy haul wagon is developed to evaluate the deterioration of dynamic behaviour under proposed fault conditions and demonstrate the detectability of the proposed FDI method. Even though the fault conditions considered in this paper did not deteriorate the wagon dynamic behaviour dramatically, the proposed FIs show great sensitivity to the bolster spring faults. The most effective and efficient FIs are chosen for fault detection and classification. Analysis results indicate that it is possible to detect changes in bolster stiffness of ±25% and identify the fault location.     

地铁车站中庭方案结构探讨

介绍某地铁车站因站位设置及管线原因采用特殊的中庭方案,以获得良好的空间感觉。与一般标准车站相比,结构侧墙及柱受力不利,因此将车站简化为平面框架模型计算。得到的结构内力表明,结构侧墙及柱受力在规范允许的范围内,证明这种新颖车站形式是可行的。     

A new generalized travel cost based connectivity metric applied to Scandinavian airports

This article proposes a new, generalized travel cost based method to operationalize network accessibility provided by airports. The approach is novel as it integrates features of network topology with multiple quality aspects of scheduled air transport services into one metric. The method estimates generalized travel costs for the full set of feasible travel paths between an airport and all network destinations. Rooftop modeling accounts for schedule delay and isolates the most cost-efficient travel paths per O-D relation. Respecting the assumed arrival time preference of passengers and adjusting for destination importance, connectivity scores are derived. The method is then applied to explore changes in the global connectivity pattern of Scandinavian airports from 2004 to 2018. The results suggest distinct spatial differences throughout the network, but less pronounced in size than suggested by popularly applied connectivity measures. Findings also highlight the importance of the geographical location as a determinate of an airport’s connectivity.