最优设计及分配理论在舰船维修中的应用研究

通过基于多服务台有限源排队系统的理论,分析舰船维修工作中在满足一定的可靠性要求下的最优设计与最优分配问题,同时结合计算机技术,提出了求解的方法,最终通过举例确定其最优设计理论的准确性。     

工程断裂构造及其公路隧道工程效应

为了解决活断层工程效应,通过对断裂构造工程效应和工程处理全过程的综合分析,理论解析了断裂构造工程效应研究的前沿课题,并结合隧道工程实践,剖析了公路隧道活断层效应应用基础研究的方案,提出了断层错动自然影响带划分、断层错动围岩稳定性空间定量评价和活断层隧道工程对策研究等需要解决的关键问题。     

沥青运输船装卸系统优化设计

针对沥青的特性,本文对沥青装卸系统进行了分析,在沥青泵组、装卸管系、伴热管系等方面提出了几种可行的设计方案,并对这些方案作了比较,指出了设计中应注意的一些问题。     

液化蒸气爆炸——火球对人体的伤害评价

为了使操作及管理人员对液化蒸气爆炸所产生的火球对人体所造成的伤害有一个具体的评判标准,本文通过数学公式及计算,结合图表,将液化气体容量与伤害范围以及对人体的伤害程度联系起来。通过此评价方法,人们可以方便地了解到爆炸火球与人体伤害程度的关系,以求更好地避免人体伤亡。实验结果证明了该算法的有效性。     

绥中北牵引变电所谐波电压分析

本文根据测试数据对绥中北牵引变电所谐波电压问题进行分析。认为谐波源来自系统侧,除了非线性负荷外,主要是由大型电力变压器激磁电流所造成。在电网负荷低谷时段,由于电压的升高使激磁电流畸变程度进一步加剧,造成绥中北变电所220 kV母线出现较高的谐波电压。     

Initial results from long-term measurements of atmospheric humidity and related parameters in the marine boundary layer at two locations in the Gulf of Mexico

Measurements of boundary layer moisture have been acquired from Rotronic MP-100 sensors deployed on two NDBC buoys in the northern Gulf of Mexico from June through November 1993. For one sensor, which was retrieved approximately 8 months after deployment, the post- and precalibrations agreed closely and fell well within WMO specifications for accuracy. The second sensor operated continuously from June 1993 to February 1997 (3.5 years). Buoy observations of relative humidity and supporting data were used to calculate specific humidity and the surface fluxes of latent and sensible heat. Specific humidities from the buoys were compared with observations of moisture obtained from nearby ship reports, and the correlations were generally high (0.7–0.9). Surface gravity wave spectra were also acquired. The time series of specific humidity and the other buoy parameters revealed three primary scales of variability, small (h), synoptic (days), and seasonal (months). The synoptic variability was clearly dominant and occurred primarily during September, October, and November. Most of the synoptic variability was due to frontal systems that dropped down into the Gulf of Mexico from the continental US followed by air masses which were cold and dry. Cross-correlation analyses of the buoy data indicated that: (1) the moisture field was highly coherent over distances of 800 km or more in the northern Gulf of Mexico; and (2) both specific humidity and air temperature served as tracers of the motion associated with propagating atmospheric disturbances. These correlation analyses also revealed that the prevailing weather systems generally entered the buoy domain from the South prior to September, but primarily from the North thereafter. Spectra of the various buoy parameters indicated strong diurnal and semidiurnal variability for barometric pressure and sea surface temperature (SST) and lesser variability for air temperature, wind speed and significant wave height. The surface fluxes of latent and sensible heat were dominated by the synoptic events which took place from September through November with the transfer of latent heat being primarily from the ocean to the atmosphere. Finally, an analysis of the surface wave observations from each buoy, which included calculations of wave age and estimates of surface roughness, indicate that major heat and moisture flux events coincide with periods of active wave growth, although the data were insufficient to identify any causal relationships.     

石板坡长江大桥复线桥工程专用水泥对混凝土性能影响研究

针对石板坡长江大桥复线桥结构和施工特点生产的专用水泥通过对水泥矿物组成及水化热的控制,对降低混凝土温升,提高混凝土体积稳定性和耐久性起到了直接、有效的作用。采用专用水泥配制的高性能混凝土具有良好的综合技术性能。     

确定焊接反变形的数值模拟及规律分析

焊接接头附近局部的加热及冷却使被焊结构产生残余应力及角变形.目前在船厂精度控制中,通常采用构件焊接后对某些部位进行火工校正的方法来控制残余角变形.文章提供了另外一种有效控制结构残余角变形的方法:对结构焊前施加弹性的反向变形.利用热弹塑性有限元法来模拟结构的焊接过程,并对不同板厚、不同热源的结构分别进行数值模拟,最终确定焊接结构的弹性反变形规律:焊接前施加弹性反变形的结构在焊接后角变形趋于零.     

3-D numerical and experimental analysis for airflow within a passenger compartment

People use cars so frequently that they always consider the air-conditioning, and thermal comfort of the driver and passenger when buying a new car. Therefore accurate simulation of the thermal performance of automobile air conditioners to improve human comfort has become increasingly important. In order to improve the thermal comfort of passengers, 3-D flow motion and thermal behavior within vehicles must be analyzed. In this paper, a numerical simulation was used to investigate thermal behavior in a vehicle. Because air temperature at an air vent is related to the cooling capacity of the air conditioner, the cooling capacity was calculated using ɛ-NTU (effective number of transfer unit) theoretical equations. Using the air temperature relationship between inlet and outlet vents as boundary conditions, a 3-D unsteady κ-ɛ turbulent model was used to give a transient analysis simulation of the temperature field and flow conditions in a vehicle’s passenger cabin. Cooling cycle analysis and conjugate heat transfer analysis at the inside surface of the cabin’s ceiling, floor and sides were also considered. The predicted temperature distributions in the vehicles passenger cabin were in good agreement with those obtained experimentally.     

Thermal design of automobile exhaust based thermoelectric generators: Objectives and challenges

The potential for thermoelectric power generation (via waste heat recovery onboard automobiles) to displace alternators and/or provide additional charging to a vehicle battery pack has increased with recent advances in thermoelectric material processing. In gasoline fueled vehicles (GFVs), about 40% of fuel energy is wasted in exhaust heat, while a smaller amount of energy (30%) is ejected through the engine coolant. Therefore, exhaust-based thermoelectric generators (ETEG) have been a focus for GFV applications since the late 1980s. The conversion efficiency of modern thermoelectric materials has increased more than three-fold in the last two decades; however, disputes as to the thermal design of ETEG systems has kept their overall efficiency at limited and insufficient values. There are many challenges in the thermal design of ETEG systems, such as increasing the efficiency of the heat exchangers (hot box and cold plate), maintaining a sufficient temperature difference across the thermoelectric modules during different operating conditions, and reducing thermal losses through the system as a whole. This paper focuses on a review of the main aspects of thermal design of ETEG systems through various investigations performed over the past twenty years. This paper is organized as follows: first, the construction of a typical ETEG is described. The heat balance and efficiency of ETEG are then discussed. Then, the third section of this paper emphasizes the main objectives and challenges for designing efficient ETEG systems. Finally, a review of ETEG research activities over the last twenty years is presented to focus on methods used by the research community to address such challenges.