弹性接触问题的位移-力法有限元解法研究

本文根据接触状态下的有限元基本方程,通过对定解条件、约束条件的分析应用,得出了仅与接触点有关的定解方程。 运用所编制的电算程序对某柴油机副连杆销及孔在最大载荷下的失圆变形进行了计算。通过采用空心及实心销两种简化模型计算得出了实际副连杆销的失圆变形范围。     

探地雷达数值模拟及其在隧道检测中的应用

利用时域有限差分(FDTD)方法,对隧道工程检测中常见检测目标进行数值模拟,分析脱空、单层钢筋、双层钢筋等目标体的探地雷达反射信号图像特征,并对隧道检测中的雷达信号图像采用遗传算法进行反演,引入目标相关系数用于反演结果全局寻优,实现对多次反射的压制,降低浅部钢筋反射信号对识别深部目标体的影响。通过对数值模拟结果进行反演,证明该方法理论上的有效性,并结合工程实践中的应用效果,说明该方法的优点与局限性。     

九岭山隧道塌方治理及塌方治理效果检测

武吉高速公路九岭山隧道是大庆至广州国家高速公路的重要控制性工程,当隧道开挖至ZK102 217时出现了塌方,滑塌范围高约19 m、宽约13 m,塌方量为4 000 m3。根据现场地质条件,分析认为围岩结构(弱风化板岩,钙质或硅质胶结,岩质坚硬,呈块状镶嵌结构)及地下裂隙水是产生塌方的主要原因。采用的处理措施是加强区段支护、回填塌腔、提高松散体的整体强度,并采用"稳住塌方区、固结塌体、超前加固"的分阶段处理方法。施工中采用φ42超前小导管超前支护、φ42系统小导管压浆固结等措施;开挖采用正台阶法以及拱脚加设锁脚小导管、侧壁施作中空注浆锚杆等措施;通过地质雷达无损检测手段对塌方处理效果进行检测,并根据检测结果进行二次处理。     

钢网面板加筋土挡墙动力特性试验的变形研究

基于泥质红砂岩粗粒土填料，采用MTS分别模拟地震荷载、交通荷载、加-卸载多循环荷载进行大尺寸模型试验，研究了钢网面板土工格栅加筋土挡墙在上述荷载作用下的动力特性，获得了不同峰值的水平地震激励下模型挡墙不同位置的水平动位移、竖向动位移峰值响应等实测值；采用不同频率、不同幅值的竖向交通荷载正交试验法，获得了该模型挡墙在重复荷载作用下的最大水平变形、最大沉降量及位置等动力特性参数值；通过7种荷载、21组加卸载循环试验，获得了加一卸载多循环荷载作用下的实测沉降值。试验结果表明：该加筋结构具有整体变形的特性，是优良的抗震结构，能承受抗震设防烈度为9度的地震荷载；同时该加筋结构具有良好的稳定性和抗破坏性，重复荷载的幅值和振动次数对结构动力变形特性的影响较大，而振动频率对变形特性的影响不显著；多循环荷载作用下该加筋结构能够明显减小不均匀沉降。过长的筋材并不能明显地改善加筋土挡墙的动力特性。     

Analysis on Ground Surface Deformation and Influence of Construction Parameters Caused by Two Different Shield Machines in Double-tube Tunnelling北大核心CSCD

Based on a shield-driven running tunnel project of Hangzhou Metro Line 2, this paper carries out field measuring of the ground surface deformation caused by two different shield machines in double-tube tunnelling in soft soil areas, obtains the laws of the surface deformation caused by shield-driven double-tube tunnelling and verifies the applicability of the modified Peck formula to double-tube tunnelling. The results show that in soft soil areas the impacts on ground surface deformation caused by different shield construction parameters in the previously and subsequently excavated tunnels are different, while the surface deformation changes sharply before and after the shield machine passing through the cutting face, and a rebound phenomenon occurs when the shield tail passes through the cutting face due to the influence of the grouting; The cutterhead torque of the shield machine in soft soil areas can be composed of five calculation factors, and the calculation results are in good agreement with the measured values. The larger the opening rate of the shield cutterhead is, the larger the average torque value will be, the higher the percentage of large ground loss rate will be, and the larger the maximum ground surface settlement will be; The ratio of cutterhead torque T to mucking volume per ring Q is used as the control parameter for analyzing the ground surface settlement, and a certain positive correlation between the ratio and the surface settlement value is determined, the smaller the cutterhead opening rate is, the more accurate the fitting results will be. © 2022, Editorial Office of "Modern Tunnelling Technology". All right reserved.     

汽车电线束图纸插接件标注缺陷及插接件代用查询浅谈

针对现有汽车电线束图纸中插接件标注缺陷进行分析,提出改进的标注方法,对插接件代用及查询方法进行简单介绍。     

某城市客车铰盘结构强度分析

分析铰盘结构在各种行驶工况时的受力特点;建立铰盘结构的有限元模型及边界条件;计算某城市客车铰盘在各种工况下的应力分布及最大应力,为铰盘结构的改进及轻量化提供参考。     

浅析武广客专弹性链形悬挂中负弛度问题

对武广客运专线接触网安装中出现的负弛度现象进行了探讨和分析,总结出导致该现象的原因,并提出相应的改进建议。     

自主品牌汽车连接器存在的问题及解决思路

线束连接器是整车线束各分段之间、线束和用电器之间连接的桥梁,它能否正常可靠连接,不仅关系到整车用电器能否正常工作,并且关系到整车的安全性,可见其重要性。国外各大主机厂都对线束连接器进行了严格的控制,但自主品牌汽车在线束连接器领域存在诸多问题。本文重点介绍自主品牌汽车线束连接器存在的问题以及解决思路。     

A closed-loop dynamic simulation-based design method for articulated heavy vehicles with active trailer steering systems

This paper presents a closed-loop dynamic simulation-based design method for articulated heavy vehicles (AHVs) with active trailer steering (ATS) systems. AHVs have poor manoeuvrability at low speeds and exhibit low lateral stability at high speeds. From the design point of view, there exists a trade-off relationship between AHVs’ manoeuvrability and stability. For example, fewer articulation points and longer wheelbases will improve high-speed lateral stability, but they will degrade low-speed manoeuvrability. To tackle this conflicting design problem, a systematic method is proposed for the design of AHVs with ATS systems. In order to evaluate vehicle performance measures under a well-defined testing manoeuvre, a driver model is introduced and it ‘drivers’ the vehicle model to follow a prescribed route at a given speed. Considering the interactions between the mechanical trailer and the ATS system, the proposed design method simultaneously optimises the active design variables of the controllers and passive design variables of the trailer in a single design loop (SDL). Through the design optimisation of an ATS system for an AHV with a truck and a drawbar trailer combination, this SDL method is compared against a published two design loop method. The benchmark investigation shows that the former can determine better trade-off design solutions than those derived by the latter. This SDL method provides an effective approach to automatically implement the design synthesis of AHVs with ATS systems.