Experimental investigation of evaporation rate and exhaust emissions of diesel engine fuelled with cotton seed methyl ester and its blend with petro-diesel

An experimental study to measure the evaporation rates, engine performance and emission characteristics of cotton seed biodiesel (cotton seed oil methyl ester) and its blends in different volumetric proportions with diesel is presented. The thermo-physical properties of all the fuel blends have been measured and presented. Evaporation rates of neat cotton seed biodiesel, neat diesel and their bends have been measured under slow convective environment of air flowing with a constant temperature. Evaporation constants have been determined by using the droplet regression rate data. The neat fuels and fuel blends have been utilized in a test engine with different load conditions to evaluate the performance, combustion and emission characteristics of the fuels. The specific fuel consumption values of the two blends, viz. B25 and B75 are found to be same. At the highest load, B0 records the lowest CO volume followed by B100. From the observed evaporation, performance and emissions characteristics, it is suggested that a blend of B50 and B75 can be optimally used in standard diesel engine settings.     

Hardware-in-the-loop testbed for evaluating connected vehicle applications

Connected vehicle environment provides the groundwork of future road transportation. Researches in this area are gaining a lot of attention to improve not only traffic mobility and safety, but also vehicles’ fuel consumption and emissions. Energy optimization methods that combine traffic information are proposed, but actual testing in the field proves to be rather challenging largely due to safety and technical issues. In light of this, a Hardware-in-the-Loop-System (HiLS) testbed to evaluate the performance of connected vehicle applications is proposed. A laboratory powertrain research platform, which consists of a real engine, an engine-loading device (hydrostatic dynamometer) and a virtual powertrain model to represent a vehicle, is connected remotely to a microscopic traffic simulator (VISSIM). Vehicle dynamics and road conditions of a target vehicle in the VISSIM simulation are transmitted to the powertrain research platform through the internet, where the power demand can then be calculated. The engine then operates through an engine optimization procedure to minimize fuel consumption, while the dynamometer tracks the desired engine load based on the target vehicle information. Test results show fast data transfer at every 200 ms and good tracking of the optimized engine operating points and the desired vehicle speed. Actual fuel and emissions measurements, which otherwise could not be calculated precisely by fuel and emission maps in simulations, are achieved by the testbed. In addition, VISSIM simulation can be implemented remotely while connected to the powertrain research platform through the internet, allowing easy access to the laboratory setup.     

Multi-criteria optimization of traffic signals: Mobility,safety, and environment

Two-dimensional multi-objective optimizations have been used for decades for the problems in traffic engineering although only few times so far in the optimization of signal timings. While the other engineering and science disciplines have utilized visualization of 3-dimensional Pareto fronts in the optimization studies, we have not seen many of those concepts applied to traffic signal optimization problems. To bridge the gap in the existing knowledge this study presents a methodology where 3-dimensional Pareto Fronts of signal timings, which are expressed through mobility, (surrogate) safety, and environmental factors, are optimized by use of an evolutionary algorithm. The study uses a segment of 5 signalized intersections in West Valley City, Utah, to test signal timings which provide a balance between mobility, safety and environment. In addition, a set of previous developed signal timing scenarios, including some of the Connected Vehicle technologies such as GLOSA, were conducted to evaluate the quality of the 3-dimensional Pareto front solutions. The results show success of 3-dimensinal Pareto fronts moving towards optimality. The resulting signal timing plans do not show large differences between themselves but all improve on the signal timings from the field, significantly. The commonly used optimization of standard single-objective functions shows robust solutions. The new set of Connected Vehicle technologies also shows promising benefits, especially in the area of reducing inter-vehicular friction. The resulting timing plans from two optimization sets (constrained and unconstrained) show that environmental and safe signal timings coincide but somewhat contradict mobility. Further research is needed to apply similar concepts on a variety of networks and traffic conditions before generalizing findings.     

Optimal bus fleet management strategy for emissions reduction

Transportation is a major cause for environmental degradation via exhaust emissions. For many transit-oriented metropolitan areas, bus trips often constitute a sizeable mode share. Managing the bus fleet, in particular updating buses to comply with the newer emissions standards, therefore, can have a substantial impact on transportation-induced air quality. This paper presents the approach of remaining life additional benefit–cost (RLABC) analysis for maximising the total net benefit by either early-retiring or retrofitting the current bus fleet within their lifespans. By referring to the net benefits for different bus types estimated by RLABC analysis, the most beneficial management scheme for the current bus fleet can be identified. Optimal bus fleet management (BFM) models based on the RLABC analysis for the operator and the government are developed. Then a government subsidy plan is produced to achieve win–win solutions, which will offer efficient and flexible management schemes. To illustrate the approach, the largest bus company in Hong Kong, which carries more than 23% of the total trips in Hong Kong, is taken as a case study example. Instead of adopting a fixed retirement plan, such as replacing buses at the age of 17 as is currently practised, the proposed method develops an optimal BFM scheme that progressively phases out buses or retrofits them. This study produces promising results to demonstrate the large benefit of this approach for optimal bus fleet management.     

Simulating the air quality impacts of traffic calming schemes in a dense urban neighborhood

In this study, the effects of isolated traffic calming measures and area-wide calming schemes on air quality in a dense neighborhood were estimated using a combination of microscopic traffic simulation, emission, and dispersion modeling. Results indicated that traffic calming measures did not have as large an effect on nitrogen dioxide (NO₂) concentrations as the effect observed on nitrogen oxide (NO_x) emissions. Changes in emissions resulted in highly disproportional changes in pollutant levels due to daily meteorological conditions, road geometry and orientation with respect to the wind. Average NO₂ levels increased between 0.1% and 10% with respect to the base-case while changes in NO_x emissions varied between 5% and 160%. Moreover, higher wind speeds decreased NO₂ concentrations on both sides of the roadway. Among the traffic calming measures, speed bumps produced the highest increases in NO₂ levels.     

从一起船舶主机拉缸故障谈柴油机润滑油的选用

通过某LPG船一起主机拉缸案例,阐述船舶柴油机润滑油合理选用和管理的重要性,讨论选用润滑油应根据船舶柴油机的型号、燃油品质等具体情况,充分考虑润滑油的黏度等级和碱度。介绍船用柴油机润滑油国内外主要生产商及其相应的产品牌号。     

基于SoftPLC的船舶主机遥控物理仿真模拟器设计

模拟器以一艘1600 TEU集装箱船使用的Autochief IV主机控制系统作为原型,采用SoftPLC实现对船舶主机遥控物理仿真模拟器的控制。利用组态软件PIMS作为上位机开发平台,实现数据的存储及功能的完善。在模拟器上可以进行各种相关的训练操作,达到培训学员的目的。     

Influence of AC system design on the realisation of tractive efforts by high adhesion locomotives

The main task for heavy haul railway operators is to reduce the cost of exported minerals and enhance the long-term viability of rail transport operations through increasing productivity by running longer and heavier trains. The common opinion is that this is achievable by means of implementation of high adhesion locomotives with advanced AC traction technologies. Modern AC high adhesion locomotives are very complex mechatronic systems and can be designed with two alternative traction topologies of either bogie or individual axle controls. This paper describes a modelling approach for these two types of AC traction systems with the application of an advanced co-simulation methodology, where an electrical system and a traction algorithm are modelled in Matlab/Simulink, and a mechanical system is modelled in a multibody software package. Although the paper concentrates on the analysis of the functioning for these two types of traction control systems, the choice of reference slip values also has an influence on the performance of both systems. All these design variations and issues have been simulated for various adhesion conditions at the wheel–rail interface and their influence on the high traction performance of a locomotive equipped with two three-axle bogies has been discussed.     

小型直喷式柴油机燃用生物质能燃料的性能研究

文章主要研究了生物质能混合燃料在柴油机上的应用,通过在一台小型直喷式柴油机上进行不同组分柴油-生物柴油-乙醇混合燃料的燃烧、油耗和排放性能对比试验,分析了乙醇含量的改变对混合燃料的发动机燃烧压力、滞燃期、放热规律、比油耗和排放的影响．     

后轮对独立回转转向架与传统转向架曲线通过性能的对比研究

利用典型的线性稳态模型对传统转向架和新型转向架（后轮对独立回转转向架）的曲线导向能力进行了分析。建立了具有14个自由度的非线性车辆模型,对最佳的一系纵向刚度布置（前导轮对的纵向刚度较小,跟从轮对的刚度较大）的新型转向架和传统转向架车辆的曲线性能进行了仿真对比。仿真结果表明,新型转向架的曲线导向性能优于传统转向架。