基于PLC的模糊频载调节器设计

介绍可编程序控制器(PLC)实现船舶电站模糊调频调载的软硬件实现方法,采用离线计算、在线查表的方法在PLC上实现模糊控制,利用硬件在环仿真进行试验研究,结果表明,智能频载控制器具有较好的稳、动态性能。     

Key technologies of ship remote control system in inland waterways under ship-shore cooperation conditions北大核心CSCD

［Objective ］ To meet the requirements of remotely controlling ship in curved, narrow and crowded inland waterways, this paper proposes an approach that consists of CNN-based algorithms and knowledge based models under ship-shore cooperation conditions. ［Method］On the basis of analyzing the characteristics of ship-shore cooperation, the proposed approach realizes autonomous perception of the environment with visual simulation at the core and navigation decision-making control based on deep reinforcement learning, and finally constructs an artificial intelligence system composed of image deep learning processing, navigation situation cognition, route steady-state control and other functions. Remote control and short-time autonomous navigation of operating ships are realized under inland waterway conditions, and remote control of container ships and ferries is carried out. ［Results］The proposed approach is capable of replacing manual work by remote orders or independent decision-making, as well as realizing independent obstacle avoidance, with a consistent deviation of less than 20 meters. ［Conclusions］The developed prototype system carries out the remote control operation demonstration of the above ship types in such waterways as the Changhu Canal Shenzhou line and the Yangtze River, proving that a complete set of algorithms with a CNN and reinforcement learning at the core can independently extract key navigation information, construct obstacle avoidance and control awareness, and lay the foundation for inland river intelligent navigation systems. © 2022 Journal of Clinical Hepatology. All rights reserved.     

提高公路路面摊铺平整度的方法探析

公路路面施工质量和行车舒适性主要通过公路路面摊铺平整度来反映。通过对公路路面平整度的影响因素进行分析，探讨提高公路路面摊铺平整度的方法，可为相关公路施工提供参考。     

基于沉降差的填石路堤施工工艺与质量控制研究

结合南方地区填石路堤施工,通过填石路堤试验段研究,介绍了填石路堤的施工工艺和质量控制要求,并通过沉降差检测分析,说明了沉降差作为填石路堤质量控制指标的可行性,为同类工程提供参考.     

公路沥青混凝土路面施工质量控制措施探析

沥青是我国用于公路路面铺设的典型材料.对沥青混凝土路面施工质量控制进行分析,并提出相应的施工质量控制措施,为施工企业提供借鉴.     

Signal control optimization for automated vehicles at isolated signalized intersections

Traffic signals at intersections are an integral component of the existing transportation system and can significantly contribute to vehicular delay along urban streets. The current emphasis on the development of automated (i.e., driverless and with the ability to communicate with the infrastructure) vehicles brings at the forefront several questions related to the functionality and optimization of signal control in order to take advantage of automated vehicle capabilities. The objective of this research is to develop a signal control algorithm that allows for vehicle paths and signal control to be jointly optimized based on advanced communication technology between approaching vehicles and signal controller. The algorithm assumes that vehicle trajectories can be fully optimized, i.e., vehicles will follow the optimized paths specified by the signal controller. An optimization algorithm was developed assuming a simple intersection with two single-lane through approaches. A rolling horizon scheme was developed to implement the algorithm and to continually process newly arriving vehicles. The algorithm was coded in MATLAB and results were compared against traditional actuated signal control for a variety of demand scenarios. It was concluded that the proposed signal control optimization algorithm could reduce the ATTD by 16.2–36.9% and increase throughput by 2.7–20.2%, depending on the demand scenario.     

起伏基岩地层盾构姿态控制及刀具配置分析

为了解决在起伏基岩地层中盾构掘进姿态控制困难及刀盘不均匀消耗问题,以长沙地铁2号线西延线盾构区间为工程实例,通过对现场油缸推力关系统计分析,得出盾构区间直线段和曲线段地层由软至硬和由硬至软的合理的油缸推力比,并应用于工程实际,得出相应的直线段和曲线段的水平、竖向偏差且均满足轴线偏差不超过50 mm的标准要求。同时,通过对现场每百米刀具更换情况统计分析,得出合理的刀具改良配置建议。     

广东山区高速公路挖方边坡常见病害及防治策略

广东省山区高速公路发展迅速,但诸多挖方边坡在修建过程中就产生了不同程度的病害。这些病害产生的原因包括气候、地质条件和人为因素,给施工工期、造价及安全管理造成较大影响。鉴于塌方病害在广东地区山区高速公路挖方边坡中较为常见,根据破坏方式及影响范围的深度将其划分为浅层溜塌、浅层滑塌和深层滑塌(滑坡)。结合工程建设经验,提出了山区路堑边坡的防治策略,可为类似工程的设计、施工提供借鉴。     

南昌红谷沉管隧道短管节干坞内拉合对接施工技术

沉管隧道最终接头短管节在牵移和拉合过程中易发生偏移与倾斜,且GINA止水带压缩到设计值难度较大。以南昌红谷沉管隧道为例,从准备、牵移、拉合及后处理4个阶段介绍短管节对接拉合施工工艺。通过对底钢板打磨、涂抹黄油等,减小底部摩擦阻力。采用计算机控制液压同步提升系统、液压数据量测、钢端壳间距测量等措施,对短管节轴线及平面控制。实践表明:GINA止水带压缩量误差仅为+4 mm,短管节轴线及平面偏差均在可控范围内,短管节干坞内拉合对接操作可行、质量可靠。     

我国城市防洪排涝地下深隧规划设计与施工方法

为了建设符合中国国情的地下排水深隧,解决城市内涝问题,消除"城市看海"现象,采用调研分析的研究方法,通过调研国外城市排水深隧建设的成功案例,借鉴成熟经验并结合我国国情探索出我国城市排水深隧在规划设计、施工技术等方面的建设模式。主要结论如下:1)深隧规划必须坚持雨污分流原则,防涝标准应设为百年一遇;2)深隧层位应建于地下30~50 m的位置,隧道管线应布设在城市易涝区,并且将修建深隧、改造浅管和清淤河道衔接起来,形成一套完整的防洪排涝系统,让深隧的作用得以充分发挥,才能解决城市内涝问题;3)排水深隧要注重防水设计,防止雨水污染地下水;4)为提高深隧的经济效益,应将深隧与地下快速路的规划结合起来,功能上多样化。