数字滤波检漏仪检测实用技术

通过对几种检测管道漏泄方法的优缺点比较,得出目前铁路供水管网检漏设备最为实用的设备是数字滤波检漏仪。根据多年的检漏实践,归纳出检测管道泄漏点综合操作程序。     

关于“走出去”铁路建设项目概预算编制的几点心得

结合我国铁路＂走出去＂项目概预算编制工作,阐述编制我国周边国家铁路建设项目概预算时应注意坚持的几点原则。＂走出去＂项目概预算编制应注意的问题为,先将其视为国内项目编制概预算,再进行国外人工费调整,以及材料费（直发料、厂发料、当地料、燃油料）、运价、取费调查,在掌握基础资料的基础上,通过对工料机资料的综合分析,合理确定综合单价、取费标准等,使编制的投资概算全面、科学、合理,真实反映项目的造价水平。     

发动机冷却水套内三维流动的数值模拟研究

应用FIRE软件对某一发动机冷却水套进行了三维数值模拟，得到了冷却液流场速率、换热系数分布、压力损失以及流量分布等流场信息。从计算结果中发现，该发动机缸体水套的第2缸、第3缸等区域存在流动死区．水套进、排气侧流量分布相差较大．整体水套压力损失与同类机型相比偏小等不合理的流动现象，是导致其第2缸、第3缸“拉缸”的主要原因。最后提出了相应的解决方案。     

埋地输油管道腐蚀调查及改造设计

针对龙鞍埋地输油管道的腐蚀现状 ,通过检测数据 ,对管线的腐蚀环境、防腐层状况、管体腐蚀等情况进行分析和评价 ,探讨腐蚀原因和机理 ,并提出了管道改造的设计方案 ,对方案的优缺点及经济因素进行了分析和比较     

摩托车发动机水冷化初探

摩托车发动机水冷化需要进行整个系统的设计、分析及计算。由于摩托车发动机本身结构紧凑、体积小,再设计布置水道有一定的难度,最好进行三维实体造型设计。为了在设计时尽量减少投入、简化结构和降低制造成本,在进行水冷化的过程中应注意产品的继承性和通用性。     

CM模式在我国城市轨道交通项目管理中的应用

为探索城市轨道交通建设项目管理模式,本文在揭示了目前城市轨道工程特点及存在主要矛盾的基础上,介绍了新型CM建设管理模式的特征和优点;分析了在我国城市轨道交通建设领域采用CM模式的必要性和可行性,提出了推行CM模式的相应方案和步骤。     

空气罐控制输液管道水击研究

采用特征线法对瞬时关闭管道终端阀门 ,在安装和不安装空气罐两种状况时 ,管道压力的变化情况进行了数值模拟 ,并分析了空气罐初始容积、空气罐安装位置等参数对管道瞬态水击压力变化的影响 ,结果表明 :在输液管道的适当位置安装容积一定的空气罐能较好地控制水击的产生     

含水率对路用水泥混凝土的影响及微波在线测湿系统

在讨论了含水率对路用土质量的影响因素后，通过对不同种类测试器的分析，确定了较为适用的微波传感器，并给出了微波传感器的输出电压与集料含水率之间的关系式，进而对测试准确度进行计算。     

Towards a model of hydrodynamic damping for a circular cylinder with helical strakes at low KC

This paper investigates the hydrodynamic damping of a circular cylinder with helical strakes at Keulegan-Carpenter (KC) number from 0.07 to 3 in the presence of steady currents. Experiments were performed with a straked cylinder oscillating in either in-line or cross currents over Reynolds number (based on the oscillating velocity amplitude) varying from 1260 to 54,000. With in-line current being present, the measured drag coefficients of the straked cylinder are found to depend on the ratio between the oscillating velocity amplitude and the steady current velocity. This phenomenon is further confirmed by computational fluid dynamics using large-eddy simulations. The drag coefficients obtained from the numerical simulations agree well with the experimentally determined values. Similar phenomenon is observed for the cases with cross background current. Based on the experimental data, empirical formulae are proposed to evaluate drag coefficients. These results are of importance in estimating the resonant motion and the fatigue life of risers, e.g. water intake risers, in the flow regime of low KC. Finally, recommendations are provided for fatigue analysis of risers with helical strakes from the perspective of engineering practice.     

Modeling free-flow speed according to different water depths—From the viewpoint of dynamic hydraulic pressure

In this paper, we propose a method of modeling free flow speed from the viewpoint of hydroplaning. First, the lift forces for different water depths were estimated using Bernoulli’s equation. Compared with the result of the experimental test performed by the Japan Automobile Research Institute, the hydrodynamic pressure coefficient was determined to be 0.03 (tf s²/m⁴). The validation of the predicted lift force is found in another published paper. A very good match is found between the computed values by the proposed numerical model and the data in other published papers. Then, the loss of contact force is considered to evaluate the hydroplaning performance of a tire. To simulate the hydroplaning speed, a tire-sliding model was utilized to obtain the traction and friction forces between the road surface and the tire. The observation data obtained in Japan in 2009 is compared with the physically computed hydroplaning speed, yielding the conclusion that the traction force at the measured desired speed is, on average, 23.4% of the traction force at hydroplaning speed. The analytical model offers a useful tool to quantitatively show that the free flow speed changes as the water depth increase.