五螺杆泵型线分析及改进

简缩了传统五螺杆泵齿型实用计算,并对型线改进进行探讨.给出提高五螺杆泵性价比的方案及计算实例,以供不同生产条件之参考.     

"圆齿-共轭曲线"内啮合齿轮泵的齿廓设计和大圆弧拟合

以无填隙片结构的1齿差内啮合齿轮泵为例介绍共轭齿廓的求法及拟合;强调了曲线的内、外包络是其内、外法向等距线而不是平行等距线的概念.给出了"圆齿-共轭曲线"齿廓的解析解及工程实用的高精度圆弧拟合实例.     

基于高阶谱的水下目标识别

利用高阶谱估值法,对具有很强非高斯性和非线性的舰船辐射噪声信号进行分析及特征提取,并通过结构自适应神经网络作为分类实验,表明基于高阶谱的特征提取具有较强的类别可分性,在无源声纳目标识别中特具潜力。     

京唐城际铁路速度目标值选择

速度目标值是城际铁路最主要技术标准,不同的速度目标值决定了基础设施、设备及各项配套设施的选择。从京唐城际铁路功能定位出发,通过对客流特点、功能定位、时间目标值需求、经济技术比选等多方面因素的分析,综合得出京唐城际铁路速度目标值推荐采用350 km/h的方案。     

An exploratory investigation of the impact of ramp metering on driver acceleration behavior

Ramp metering has been proven as an effective freeway management strategy; however, the impact of ramp metering on drivers' acceleration behavior has not been fully investigated. A better understanding of acceleration behavior changes with ramp metering is critical to the adequate design of ramp metering facilities. In this study, drivers' speed and acceleration data were collected at two representative metered ramps in Los Angeles, California. The speed and acceleration profiles under meter-on and meter-off scenarios were compared. Statistical results demonstrated that ramp metering affects drivers' acceleration behavior at ramp acceleration lane. It was found that at the metered ramp with short existing acceleration length, the average acceleration rate from ramp meter stop bar to 500 ft downstream under meter-on scenario (4.72 ft./s²) is approximately 40% higher than when meter-off (3.18 ft./s²). The design of acceleration lane length for metered on-ramps should therefore take into account the potential impacts of ramp metering on driver acceleration behavior.     

浅谈沥青混合料配合比设计四个阶段

介绍了沥青混凝土配合比设计的四个阶段及各阶段的主要技术要点,供同行参考。     

基于知识积累的软件运行剖面生成方法及黑箱测试技术

软件的黑箱测试是一个面向用户的软件测试方法，当它以运行剖面为基础生成测试案例时，运行剖面的完备性将直接影响其测试结果的可信性，基于知识积累的软件运行剖面生成方法就是试图通过知识的获取和积累使生成的运行剖面日趋完备，从而达到黑箱测试技术在某些特殊的软件测试领域中更具实用和可信。文章讨论了软件 运行剖面的完备性和软件失效类等概念，提出了一种基于知识各界的软件运行剖面生成广阔圾黑箱测试技术，这种技术现已     

上海轨道交通一号线102号列车C1车体顶盖结构设计

介绍上海轨道交通一号线102号列车C1车体顶盖结构的设计原理、顶盖各结构件的组成,并阐述大断面铝型材在车体顶盖中的应用,以及标准化、模块化的先进设计理念在顶盖设计中的应用。     

A shockwave profile model for traffic flow on congested urban arterials

In this paper a new traffic flow model for congested arterial networks, named shockwave profile model (SPM), is presented. Taking advantage of the fact that traffic states within a congested link can be simplified as free-flow, saturated, and jammed conditions, SPM simulates traffic dynamics by analytically deriving the trajectories of four major shockwaves: queuing, discharge, departure, and compression waves. Unlike conventional macroscopic models, in which space is often discretized into small cells for numerical solutions, SPM treats each homogeneous road segment with constant capacity as a section; and the queuing dynamics within each section are described by tracing the shockwave fronts. SPM is particularly suitable for simulating traffic flow on congested signalized arterials especially with queue spillover problems, where the steady-state periodic pattern of queue build-up and dissipation process may break down. Depending on when and where spillover occurs along a signalized arterial, a large number of queuing patterns may be possible. Therefore it becomes difficult to apply the conventional approach directly to track shockwave fronts. To overcome this difficulty, a novel approach is proposed as part of the SPM, in which queue spillover is treated as either extending a red phase or creating new smaller cycles, so that the analytical solutions for tracing the shockwave fronts can be easily applied. Since only the essential features of arterial traffic flow, i.e., queue build-up and dissipation, are considered, SPM significantly reduces the computational load and improves the numerical efficiency. We further validated SPM using real-world traffic signal data collected from a major arterial in the Twin Cities. The results clearly demonstrate the effectiveness and accuracy of the model. We expect that in the future this model can be applied in a number of real-time applications such as arterial performance prediction and signal optimization.     

改善轮轨接触状态的车轮型面几何设计方法

改进了车轮型面设计方法,给出了设计方法的解析数学表达式,将轮对等效锥度与轮轨型面接触状态联系起来,对设计实例进行了轮轨几何接触、非赫兹滚动接触和车辆动力学性能分析.研究结果表明:轮轨接触点能够均匀分散分布;由于接触斑面积增大约23%,最大接触压力降低约21%,使轮轨滚动接触应力降低了约20%;装备实例型面的车辆临界速度...