高速公路工程项目法施工管理的几点做法

以杭(州)浦(东)高速公路第七合同段为工程实例,介绍了项目法施工管理的新思路,并通过具体的工程项目对项目法施工管理进行了详细阐述。本文主要介绍项目法施工在远离施工企业本部的工程项目上的具体运作。     

宽带无线视频网络的关键技术

随着现代通信技术和业务的发展,人们对通信的需求已经由最初的单一语音需求转变为对视频和音频的通信需求,以传送语音、数据、视频为一体的视频通信业务成为通信领域发展的热点。针对宽带无线视频网络关键技术中的视频信源编码技术、信道编码技术、OFDM传输技术进行简要的介绍和分析。     

铁道车辆运行安全评判的轮对爬轨脱轨准则

为了掌握车辆爬轨脱轨机理及主要影响因素,分析了轮对的三维空间受力,推导了轮轨横向力和垂向力比值的一般表示式,假设车轮在达到最大轮缘接触角时为脱轨的临界状态,并认为这时轮轨间出现完全摩擦滑动,导出了不考虑轮对摇头角的临界脱轨判别的二维准则与考虑轮对摇头角和轮轨蠕滑率效应的三维脱轨判别准则,给出了轮轴脱轨系数的定义,采用轮轴脱轨系数和轮重减载率进行脱轨的判别。仿真计算结果表明:二维脱轨判别准则与三维准则相比偏于保守;摇头角越小甚至变负,越有利于防止脱轨,摇头角越大,三维准则的临界脱轨曲线越接近于二维准则的;减小轮轨摩擦系数与增大轮缘角均有利于防止脱轨的发生。     

Corrosion rate measurements in steel sheet pile walls in a marine environment

Corrosion of steel structures in the marine environment is a major problem. The deterioration of this kind of structures is costly and difficult to predict both when designing new structures and when estimating the remaining service life time for existing structures. The aim of this investigation was to find indicative values for the corrosion rate of steel sheet piles on the Swedish west coast. Such corrosion rates (mm/year) can be used both when designing new structures by oversizing the steel thickness and when estimating the bearing capacity of existing sheet pile structures. Earlier investigations on the corrosion rates along the Swedish east coast – with salinity from about 0.2% to 0.8% – are still used today as guidelines for the corrosion rate of all steel structures in the Swedish maritime environment even though the salinity on the west coast can be as high as 3.0%.Steel sheet pile wharfs located in the port of Halmstad on the Swedish west coast were inspected by ultrasonic measurements. Three wharf structures with a total length of about 700 m were inspected. None of the inspected wharfs had or have had cathodic protection. The thickness measurements of the steel sheet pile structures were performed by divers.The age of the three inspected sheet pile structures ranged from 36 to 51 years. The dimensions of the original sheet pile sections are known. One of the quay structures is located along a river. The salinity at all wharfs varied from low values at the surface to approx. 2% at the bottom (also in the river outflow).The measured average corrosion rates were in the same order as the design values in the European code. However, the results indicate increased corrosion rates about 1 m below the mean water surface and at the level of the propellers from the ships berthing the most frequented of the inspected wharfs, 3–6 m below water surface.The tolerances of steel sheet thicknesses – usually in the order of ±6% – are often neglected when investigating the remaining thickness in steel sheet piles. A simple calculation model shows that the sheet pile must be almost 50 years of age before an accurate estimation on the corrosion rate can be made, considering the tolerances, if the true original sheet pile thickness is not known.     

沥青路面运营初期平整度竣工验收标准研究

采用数理统计原理,运用SPSS软件对陕西省7条高速公路交-竣工平整度数据进行分析,得出了陕南、关中和陕北地区路面平整度衰变幅度均值分别为0.39m/km、0.28m/km和0.24m/km,这也将作为计算竣工验收推荐值的依据;再基于交-竣工平整度变化规律,建立了平整度竣工验收推荐值的计算公式:IRIju=IRIji+IRIs,可为今后平整度竣工验收标准提供有效的理论依据。     

数控铣床加工低碳钢零件的进给速度优化

论述了数控铣床加工低碳钢零件时进给速度的优化问题．在基于加工效率（可等效转化为加工工时）和加工成本目标函数的基础上，对这两个目标函数运用多目标函数理论进行综合，得到了多目标综合函数．通过计算，并综合表面粗糙度，进而得到进给速度的优化范围，并对不同转速下的进给速度给出了相应的优化参数，目的更接近生产实际，使技术人员不仅了解影响生产效率和成本的因素，也可在实际生产的应用中更加快捷和方便．     

基于粘弹塑性理论的沥青路面车辙分析

应用粘弹塑性理论,研究了沥青混合料一维粘弹塑性本构关系,并运用ABAQU软件建立了柔性基层沥青路面车辙分析的有限元模型,研究了路面车辙的发展规律,经环道试验进行了验证。结果表明:荷载作用初期路面车辙发展较快,而后期车辙发展较慢;路面永久变形主要由绝对车辙引起,侧向隆起仅占15%~30%;随着沥青层厚度增加,车辙增加,但增加幅度逐渐减小;从表层开始沥青层的变形率随深度的增加而逐渐变大,在8 cm处变形率达到最大值,之后逐渐减小;沥青路面车辙主要产生在结构深度20 cm深度范围以内,尤其在4~12 cm之间。另外,进行了重载作用下的路面车辙模拟,对基于车辙等效的轴载换算进行了探讨,提出轴载换算系数为5.9。     

小样本条件下混凝土强度代表值的确定

针对小样本混凝土强度代表值确定时不能利用数理统计模型的问题,引入了信息扩散原理,提出了小样本条件下混凝土强度代表值确定的实用计算模型。2个混凝土强度检测案例的计算结果表明,利用《公路工程质量检验评定标准》(JTJ071-98)进行灌注桩芯样混凝土强度代表值确定,得到的代表值保证率在95%左右波动,具有不确定性;利用《超声回弹综合法检测混凝土强度技术规程》(CECS 02:88)进行单一构件混凝土强度推定,推定值的保证率小于95%,对结构的可靠性鉴定而言是偏于不安全的,应引起试验检测人员的充分重视。     

整车试制阶段的电器故障诊断方法

以整车装车与跑车验证案例为背景，讨论汽车开发过程中汽车电器故障诊断的方法，阐述如何应用零部件置换原则来分析故障的重要性等级（significance）。