车门内水切升降异响分析及设计优化

主要针对汽车车门玻璃在下降过程中由于内水切"咕噜咕噜"异响问题的研究,结合实车案例分析影响内水切升降过程中异响的原因,并通过不断的设计优化断面和调整CLD值效果验证,最终解决异响问题;弥补了设计阶段需注意控制的相关设计参数,为以后新项目的设计提供了参考。     

简析地铁安全门驱动控制器的控制构架

针对地铁安全门驱动控制器,提出了一种电机控制软件构架。该构架以嵌入式操作系统为基础调度各控制任务,将控制任务分为高优先级任务和低优先级任务。在该控制构架基础上,完成了地铁安全门驱动控制器的软件系统,并在样机上进行了应用测试。试验表明,该电机控制软件构架运行稳定,能有序地调度各控制任务,并具有良好的复用性和扩展性。以该构架为基础开发的驱动控制系统控制精度高,动态响应好,能够满足现场应用的需求。     

Effect of Explosion in a Gas Pipeline Compartment of a Utility Tunnel on Neighboring Metro Tunnels北大核心CSCD

In this paper the numerical simulation analysis of the effect of explosion in the gas pipeline compartment of a utility tunnel on neighboring metro tunnels was conducted using the software AUTODYN. The results show that the TNT equivalent in a fireproof partition with length of 200 m is 41.6 kg when the gas concentration in the gas pipeline compartment reaches 10%; the blast wave has much effect on the crown and arch waist of the round metro tunnel and it’s necessary to take some protective measures in both areas; when the surrounding soil is sand, the utili- ty tunnel is above the round metro tunnel and their alignments are in the same direction, the greater the vertical spacing between the utility tunnel and the metro tunnel, the smaller the effect of the blast wave on the metro tunnel; when the vertical spacing is 7.2 m, the maximum dynamic tensile stress is 1.86 MPa (including the static stress value of 1 MPa in the tunnel segment) and it is slightly smaller than the designed tensile strength of metro tunnel (about 1.89 MPa). The maximum vibration velocity and the maximum displacement meet the structural stability require- ments, so it is suggested the vertical spacing between the utility tunnel and metro tunnel shall not be less than 7.2 m. © 2018, Editorial Office of "Modern Tunnelling Technology". All right reserved.     

地铁车站防火与维修通道设计冲突及解决

为了解决在前期施工过程中提前发现的地铁站中电话接线房、饮水泵房和防水泵房的防火设计与后期对相应设施的维修所存在的设计冲突,通过进行防火分区的研究以及结构受力计算和分析,在设计中采用了在电话接线房和防火房顶部增设顶板的方式来满足防火要求,此外还在饮水泵房设计中不设顶板从而满足后期对相应设施进行维修的要求。     

移动式损管训练舱堵漏水循环系统设计

文章通过3ds Max和AutoCAD软件设计出移动式损管训练舱堵漏水循环系统,在系统中完善了堵漏训练所需的配套设施,解决堵漏水的循环利用,使损管堵漏训练能满足海警官兵日常训练要求.     

Preliminary investigation of PM1, PM2.5, PM10 and its metal elemental composition in tunnels at a subway station in Shanghai,China

In this study, real-time monitoring campaigns were conducted in two tunnels (Line A and Line B) at a subway station in Shanghai, including temperature, relative humidity, PM₁, PM_2.5 and PM₁₀, in order to understand the climate and PM characteristics in the transportation microenvironment. In addition, collected floor dust particles in the tunnel were analyzed by ICP for their metal elemental composition. Strong correlations occurred between all PM levels and meteorological parameters in the tunnel of Line A (with platform screen doors), in comparison with the weak correlations between such parameters in the tunnel of Line B (without platform screen doors). PM_2.5 and PM₁₀ between peak hours and off-peak hours for both lines presented significant differences (p < 0.05), respectively. Nevertheless, PM₁ showed a different pattern, with p > 0.05 for Line A and p < 0.05 for Line B, respectively. In addition, statistical results concluded that PM had an evident weekly variation for both lines. Friday was the highest day of all particulate matters in monitoring periods for both lines. Ratios of PM₁/PM₁₀ and PM_2.5/PM₁₀ were high when trains were out of service and low when trains were in service. Relative abundance of metal elements detected from floor dust particles proved that floor dust particles in tunnels might be a major source of airborne PM in the subway microenvironments, with Fe as the most abundant metal element, followed by Ca, Al, Mg, Mn, Zn, Cu, Cr, Ni, Pb and Hg.     

基于有限元的某轿车左前车门外门板的强度分析

通过运用Hypermesh建立某轿车车门外门板的有限元模型,利用计算机辅助计算,分析了外门板在下沉和扭转工况下的应力,确保其设计是否满足强度要求,找到了车门的强度薄弱区域,并为车门其他结构的设计提供参考和依据。     

滑移门锁系统解锁力的传递与优化

降低车门开启力是提高用户对汽车第一感知质量的重要因素。文章介绍了一种滑移门门锁系统解锁力的传递过程以及优化方法,对解锁力传递链上的每一环力大小做出理论计算并分析计算过程,为降低解锁力提供了优化方案,实测解锁力结果满足规范以及客户期望。为门锁系统以及车门系统的设计提供了参考.     

新一代抽拉离心式高机动卫生防疫车的设计研究

为探索新形式下部队病媒生物防治的新需求,针对野外作战的新特点,结合平战时作业的新形势,研发了新一代卫生防疫车。经过总体结构布局,车厢结构优化,采用新型抽拉式车厢和上装模块化消杀防疫设备,以及大功率硅发电机和蓄电池组的组合供电模式,配备了消杀设备双操作模式。经过第三方评测,主要设备功能完善,性能稳定、可靠,满足技术指标要求,有利于提升中国移动医疗卫生装备的科技水平。     

多传感器融合车载电池舱灭火方法研究

电动汽车属于汽车行业的支柱产业,越来越受到社会的重视,但随之产生的汽车安全问题也逐渐增多。电池舱属于复杂环境,易出现着火事件,本文开展多传感器融合车载电池舱灭火方法研究,运用温度、烟雾浓度传感器实现对火灾的实时监测。设计贝叶斯网络模型,并考虑到了传感器失效及误报,实验结果表明本系统具有良好的响应速度及稳定性,为相关领域研究提供了一种解决方法。