自导向径向转向架构架技术设计

介绍自导向径向转向架构架的主要技术参数和基本结构,并对其进行有限元分析。     

极线约束下的多分辨率相关匹配算法

针对计算机视觉在几何测量应用中图像匹配特点,提出了将多分辨率和极线约束与相关法相结合的图像匹配方法。该方法采用金字塔分层和极线约束来弥补相关匹配带来运算量大的不足,克服了图像匹配中精度低的缺点。通过计算机视觉在几何测量检测系统中图像匹配的实际应用,验证了该算法具有较高的测量精度、速度及其实用性。     

大型全垫升气垫船设计初探

通过对全垫升气垫船气垫参数、动力系统、围裙系统、横稳性和操纵性等方面进行分析,对大型全垫升气垫船的设计进行初步的探索。     

船体与组合推进器系统推力减额特性设计主参数和优化策略研究

在文献[1]的基础上,提出了评价船后组合推进器推力减额特性的4个指标:整体推力减额效率(1-t1)、转子推力减额效率(1-t2)、组合推进器推力比τ和导管定子阻力比γ.利用CSSRC现存试验数据运用简单对比和统计分析方法,给出了诸设计参数对这些指标影响的显著性和规律性.推荐采用受控于全部主参数的指标(1-t2)作为船体与组合推进器相互干扰特性优化的总目标,提出了用部分主参数控制的对应分目标优化和迭代来实现总目标优化的简明策略.实例计算表明,优化设计船体尾型主参数LRD、CPR和推进器主参数(A)ex/AP的搭配,可大幅度提高船后组合推进器的推力减额效率.     

Links between subjective and objective evaluations regarding the steering character of automobiles

This work presents an experiment on the relationships between subjective and objective evaluations of vehicle handling. Ten cars were examined objectively in several open-loop driving dynamics manoeuvres and subjectively by test persons in typical traffic situations. Results are extracted from a stationary test (the Slowly Increasing Steer Test), and a dynamical test (the Frequency Response Test). The subjective measurements are obtained from drivers on a rural road course via a questionnaire, which was developed to separately investigate the quantity level perception, the so-called “Niveau”, and the more qualitative “Liking”. These subjective “measurements” are embedded into a two-channel definition of “Steering Comfort” as a genus for “Steering Discomfort” and “Character”. The article concentrates on developing a statistical method for the consideration of correlations amongst the subjective/objective data. In doing so, the variance in example subjective Niveau ratings can be significantly explained by several objective quantities. Indicators for co-domains of validated discomfort characteristics and hints for endeavouring character Liking ranges are detected.     

悬索管道桥结构参数对全桥动力特性的影响研究

大跨度悬索管道桥桥面窄,宽跨比小,结构十分轻柔,结构参数的改变对其动力特性有较大的影响。以川气东送野山河悬索跨越工程为例,采用大型有限元分析软件ANSYS10.0分析了风缆预张力和风缆面与水平面夹角变化对该悬索管道桥动力特性的影响。研究表明,提高风缆预张力和选取适当的风缆与水平面的夹角能有效地提高全桥结构刚度。     

冰粒参数对冰粒射流表面清洗性能的影响

根据射流对固体表面冲击时的流动过程分析,得出了冰粒射流对固体表面的作用不仅仅在冲击区,还包括附壁射流区的结论。由于冰粒是冰粒射流的关键,因而选用与冰粒相关的参数即其温度、粒径和流量作为影响因素,在射流的压力、靶距和横移速度一定的情况下,利用建立的冰粒射流系统进行了脱漆正交试验,目的是通过脱漆试验考察冰粒对其射流表面清洗性能的影响。试验数据的方差分析和直观分析表明：冰粒的温度和流量对冰粒射流表面清洗性能的影响是主要的,而粒径的影响是次要的。     

高速铁路隧道支护参数的计算研究

为探索隧道初期支护安全系数的计算问题,并为高速铁路隧道支护参数优化提供理论依据,根据喷锚支护的性能与特点以及现代隧道力学的基本理论,建立初期支护荷载结构模型和对应的安全系数计算方法; 针对时速350 km高速铁路双线隧道提出的3种不同的初期支护方案（无系统锚杆支护、喷锚结合支护和以锚为主的支护方案）展开适应性研究,计算分析不同埋深（400 m和800 m）条件下初期支护的优化参数以及优化后的二次衬砌承载能力,在此基础上提出优化后的高铁隧道支护参数建议值,并对优化前后的安全系数进行计算与对比。主要结论如下： 1）提出了采用围岩压力代表值作为荷载结构模型设计荷载的方法,为解决设计中围岩压力不确定的问题提供了思路,且所推荐的围岩压力代表值计算方法具有安全性与经济性; 2）提出了3种初期支护计算模型,可以为初期支护构件的选择与量化设计提供一定的理论基础; 3）提出了时速350 km高速铁路双线隧道初期支护方案及优化后的复合式衬砌设计参数,并明确了不同围岩级别、不同埋深时的承载主体; 4）提出了按照不同埋深进行支护结构参数设计的建议。     

岩溶富水区深埋水沟排水隧道注浆圈参数研究

为合理确定深埋水沟排水方式下隧道注浆圈特征参数,以某岩溶富水区隧道工程为依托,采用FLAC3D软件建立流固耦合计算模型,针对其注浆圈参数进行合理探讨,研究注浆圈厚度、注浆圈渗透性对隧道涌水量、衬砌水压力、结构安全性的影响规律。研究结果表明： 增加注浆圈厚度或降低注浆圈渗透性可降低衬砌水压、控制涌水量、保障结构安全,但并不代表实际工程中注浆参数需要追求最值,而应兼顾安全性和经济性,选取相对合理的注浆参数;结合模拟计算结果与同类工程案例,建议依托工程注浆圈厚度以5～6 m、渗透性比值以注浆前的1/50（渗透系数为2×10-6 cm/s）为宜,并应结合实际进行技术经济对比,合理确定现场注浆参数。     

Bolster spring fault detection strategy for heavy haul wagons

An on-board health monitoring system is proposed for heavy haul wagons in this paper including a signal-based fault detection and isolation (FDI) method and an on-line fault diagnose strategy. Such a system, to be feasible on freight wagons, must be sufficiently cheap and robust, hence the design assumes the constraint of using only two accelerometers mounted on the front left and right rear part of each carbody in a heavy haul train. This paper focuses on the detection of bolster spring fault conditions. The problem is made more complex by the modes of failure which might be expected in bolster spring nests. Types of spring failure are firstly identified and discussed covering situations of broken (shortening springs) and softening (individual spring loss from a nest or cross-section loss through corrosion). The effects of these faults and their detectability were investigated using simulations on straight and curved track and using a fully detailed model of a typical 40?t axle-load heavy haul wagon. The simulation results were then examined and compared using cross-correlation analysis and an FDI system was proposed. The FDI system introduced five possible fault indicators. Initial results indicated that it was possible to detect changes in bolster stiffness of ±25%. An on-line fault diagnoses strategy is proposed for bolster spring faults which only requires data from wagon monitoring during travel around sharp curves to detect and the occurrence of confirm faults. The functionality envisaged needs only a ‘once per trip’ monitoring site, such as a sharper curve, and is aimed at condition monitoring rather than the provision of alarms or comprehensive monitoring of all events.