城市地下道路分(合)流匝道通风阻力特性

为分析多点进出结构的城市地下道路空气流动特性,以长沙市营盘路湘江隧道为原型,通过现场实测、缩尺模型试验以及CFD软件数值模拟方法,对分(合)匝道通风阻力特性进行了研究,考察了雷诺数、风量比、分岔角度对分(合)流匝道阻力特性的影响规律。研究结果表明:1)主隧道与匝道风量比、主隧道与匝道夹角是影响分(合)流匝道局部阻力系数的关键因素;2)城市地下道路分(合)流匝道局部阻力变化特性,不宜简单套用通风管道的三通构件的参数;3)结合最小二乘法和Matlab软件对计算结果进行多因素回归分析,给出了基于长沙营盘路湘江隧道的分(合)流匝道主隧道和匝道的局部阻力系数关联式。研究结果可为复杂结构城市地下道路通风系统阻力特性分析及通风工程优化设计提供方法参考。     

“中—尼—印铁路通道”线路设计及建设可行性分析

随着我国"一带一路"倡议的推进,跨国运输通道的建设成为倡议实施的关键环节之一,而我国建设复杂地质条件下跨国基础设施的经验尚不丰富。"中—尼—印铁路通道"是一条途经尼泊尔,连接中国和印度2个大国的运输通道,基于实地考察,分析该通道建设的必要性及建成后的效益,对线路进行初步规划,并总结该通道建设的难点:铁路轨道坡度大;沿线区域地质构造复杂;周边基础设施落后,施工条件恶劣;大量深长隧道以及大跨径高桥梁;环境以及气候条件复杂。同时对沿线隧道以及桥梁的建设可行性进行分析,并给出施工建议:沿线隧道采用以TBM法为主、钻爆法为辅的施工方法;桥梁建设则因地制宜,根据不同区间的地质特点,采用相应的建设方法。     

拱架式预切槽施工机械在黄土隧道施工中的应用

隧道预切槽施工技术在国外应用比较广泛,但在我国应用还较少。针对黄土地质专项研制了国内首台拱架式预切槽机,并在黄土隧道进行了施工试验。通过施工试验,掌握设备定位、分区切灌、设备行走、施工作业组织等关键技术,并提出应用改进及优化措施。试验结果表明切槽系统工作状态和设备切削、喷灌功能满足设计及施工试验要求,为预切槽同步切削喷灌一体化研究提供了数据支撑和研究方向。     

废气旁通阀开度对增压直喷汽油机部分负荷性能的影响

汽油机节气门产生的节流损失对增压发动机泵气损失的影响相当严重,尤其是在中小负荷时,针对这一问题采用试验的方法研究了中小负荷下旁通阀开度对增压直喷汽油机性能的影响。研究结果表明,在节气门开度较小的小负荷工况下,涡轮增压器不宜工作,否则排气背压过大,对发动机非常不利;而废气旁通阀全开可以减小排气背压,能使发动机的动力性和经济性提高3%左右。对废气旁通阀的合理控制可以实现发动机在自然吸气和涡轮增压两种模式之间的转换。     

Modelling,simulation and applications of longitudinal train dynamics

ABSTRACT

Significant developments in longitudinal train simulation and an overview of the approaches to train models and modelling vehicle force inputs are firstly presented. The most important modelling task, that of the wagon connection, consisting of energy absorption devices such as draft gears and buffers, draw gear stiffness, coupler slack and structural stiffness is then presented. Detailed attention is given to the modelling approaches for friction wedge damped and polymer draft gears. A significant issue in longitudinal train dynamics is the modelling and calculation of the input forces – the co-dimensional problem. The need to push traction performances higher has led to research and improvement in the accuracy of traction modelling which is discussed. A co-simulation method that combines longitudinal train simulation, locomotive traction control and locomotive vehicle dynamics is presented. The modelling of other forces, braking propulsion resistance, curve drag and grade forces are also discussed. As extensions to conventional longitudinal train dynamics, lateral forces and coupler impacts are examined in regards to interaction with wagon lateral and vertical dynamics. Various applications of longitudinal train dynamics are then presented. As an alternative to the tradition single wagon mass approach to longitudinal train dynamics, an example incorporating fully detailed wagon dynamics is presented for a crash analysis problem. Further applications of starting traction, air braking, distributed power, energy analysis and tippler operation are also presented.     

A signal-based fault detection and classification method for heavy haul wagons

This paper proposes a signal-based fault detection and isolation (FDI) system for heavy haul wagons considering the special requirements of low cost and robustness. The sensor network of the proposed system consists of just two accelerometers mounted on the front left and rear right of the carbody. Seven fault indicators (FIs) are proposed based on the cross-correlation analyses of the sensor-collected acceleration signals. Bolster spring fault conditions are focused on in this paper, including two different levels (small faults and moderate faults) and two locations (faults in the left and right bolster springs of the first bogie). A fully detailed dynamic model of a typical 40t axle load heavy haul wagon is developed to evaluate the deterioration of dynamic behaviour under proposed fault conditions and demonstrate the detectability of the proposed FDI method. Even though the fault conditions considered in this paper did not deteriorate the wagon dynamic behaviour dramatically, the proposed FIs show great sensitivity to the bolster spring faults. The most effective and efficient FIs are chosen for fault detection and classification. Analysis results indicate that it is possible to detect changes in bolster stiffness of ±25% and identify the fault location.     

State estimation in roll dynamics for commercial vehicles

Accurate lateral load transfer estimation plays an important role in improving the performance of the active rollover prevention system equipped in commercial vehicles. This estimation depends on the accurate prediction of roll angles for both the sprung and the unsprung subsystems. This paper proposes a novel computational method for roll-angle estimation in commercial vehicles employing sensors which are already used in a vehicle dynamic control system without additional expensive measurement units. The estimation strategy integrates two blocks. The first block contains a sliding-mode observer which is responsible for calculating the lateral tyre forces, while in the second block, the Kalman filter estimates the roll angles of the sprung mass and those of axles in the truck. The validation is conducted through MATLAB/TruckSim co-simulation. Based on the comparison between the estimated results and the simulation results from TruckSim, it can be concluded that the proposed estimation method has a promising tracking performance with low computational cost and high convergence speed. This approach enables a low-cost solution for the rollover prevention in commercial vehicles.     

柴油机起动过程缸内窜机油现象的可视化研究

在单缸机上利用内窥镜技术观察到了起动过程中缸内有窜机油的现象。采用图像分析和试验验证相结合的方法,分析了缸内窜机油现象发生的原因,研究了转速和进气压力对柴油机起动倒拖工况下缸内窜机油现象的影响,研究了起动着火运行时缸内的窜机油现象以及炭烟排放特性。研究表明:柴油机高转速起动倒拖工况下,在压缩上止点前后以及排气上止点后均有机油窜入缸内;当转速升高时,窜入缸内的机油量增加;当缸内压力升高时,窜入缸内的机油量减少;在起动着火过程中,运行初期缸内出现窜机油现象,随着发动机运行时间增加,窜机油现象消失,炭烟减少。     

VVL耦合喷油策略对GDI汽油机混合气形成的影响

利用三维仿真软件Ansys Fluent建立了GDI汽油机的仿真计算模型,就变气门升程耦合不同喷油策略对缸内气流运动和混合气形成的影响进行了模拟计算。结果表明,与大气门升程工况相比,小气门升程工况的缸内湍流运动强度、燃油蒸发和湿壁情况以及点火时刻混合气质量都明显改善;在小气门升程工况,采用两段喷油会缩短油气混合时间,过度推迟二次喷油时刻会恶化混合气质量和燃油湿壁情况;在大气门升程工况,两段喷油会改善混合气均匀性,随着二次喷油时刻推迟,燃油蒸发量增加,湿壁情况加剧,混合气质量得到改善;小气门升程工况下采用二次喷油时刻为470°曲轴转角,前后两次喷油量比例为7∶3的两段喷油方案在燃油蒸发和湿壁以及点火时刻缸内混合气质量这几个方面的效果都很好,是最合理的方案。     

基于响应面和遗传算法的柴油机瞬态过程喷油参数优化

基于台架试验数据,利用响应面法建立了某工程机械用柴油机瞬态过程喷油参数与性能的近似高精度模型,基于此模型采用遗传算法对瞬态过程喷油参数分别进行离线优化研究。结果表明:采用单目标优化确定的燃油消耗率(BSFC)、NO_x比排放量和颗粒质量(PM)比排放量的优化极限分别可达180.23g/(kW·h),8.92g/(kW·h)和0.011 8g/(kW·h),相对原机可降低多达4.5%,34.0%和37.3%。双目标优化的Pareto解集表明,相比于同时优化BSFC和NO_x比排放量,BSFC和PM比排放量更容易同时得到优化。采用权重因子适应度函数的三目标优化结果对应的BSFC,NO_x比排放量及PM比排放量分别为184.70g/(kW·h),12.62g/(kW·h)和0.012 2g/(kW·h),较原机分别降低2.1%,6.6%和35.3%。改进优化模型后,性能优化Pareto解集对应的BSFC和PM比排放量水平都非常接近其优化极限,但NO_x比排放量相对其优化极限仍然较高。