盾构法联络通道密封垫设计及防水试验研究

为探究适合盾构法联络通道工程的密封垫断面形式,以宁波市轨道交通3号线第1条盾构法联络通道为工程背景,针对遇水膨胀橡胶设计阴阳凹凸、圆形孔洞、梳形、矩形等4类断面。对各断面形式进行可行性分析,选取阴阳凹凸断面与矩形断面作为初选方案。利用Abaqus/Explicit计算模块对2种断面的接触应力进行有限元分析,通过设计“一”字缝耐水压力试验,验证数值模拟中接触应力较大的矩形断面的防水能力。研究表明： 1）数值模拟结果显示,接触面最大接触应力与平均接触应力均随着张开量的增加而减小; 同等张开量与错台量下,在压缩与膨胀2个阶段中,矩形断面的接触应力均大于阴阳凹凸断面,因此选取矩形断面作为备选方案。2）“一”字缝耐水压力试验结果表明,矩形断面密封垫保压48 h后耐水压力明显提升,且张开量越大耐水压力提升幅度越大。3）综合数值模拟与试验结果可知,该矩形断面密封垫满足0.6 MPa的防水要求。     

压气条件下泥膜进气值测量试验研究

在压气条件下,进气是泥膜透气失效的起始点。为测量并研究泥膜在气压下的进气压力值（进气值）,通过自制的试验装置,在不同压气条件下对3种泥膜进行进气值测量试验。试验结果表明： 1)由闭气排水与固结排水的差值可以辨别泥膜是否进气,得到泥膜进气值; 2)采用泥膜特征孔径D90/2代入推导公式可近似计算泥膜进气值; 3)泥膜在不同压气条件下进气值不同,增压速率越低,泥膜进气值越大; 4)在较快和较慢的增压速率下存在进气值变化趋于稳定的现象,最大进气值为最小值的2倍以上。     

凿岩台车臂定位系统与液压臂结构不匹配问题研究

为解决凿岩台车臂定位系统与液压臂结构不匹配而出现液压臂下降时抖动、平动速度慢、泵压过高等问题,系统分析液压臂下降时抖动的原因,指出液压臂下降时抖动是由于液压臂下部液压缸平衡阀的先导油源压力不稳引起的,并通过试验证实,如果下降过程中下部液压缸平衡阀的先导油源压力一直大于其开启压力,液压臂能够平缓下降。可以通过提高液压臂油源压力和增大下部液压缸回油背压来解决液压臂下降抖动问题。     

盾构隧道管片接头嵌入式密封垫防水性能探究

为解决传统密封垫易于与混凝土管片胶结处发生渗漏水的问题,对新型嵌入式密封垫的防水性能进行研究。与传统的现场粘贴防水橡胶密封垫的工艺不同,嵌入式密封垫是将密封垫与混凝土管片整浇预制。采用模型试验和有限元数值模拟方法,对隧道接头中嵌入式密封垫的防水能力进行分析和论述。研究结果表明： 文中所涉截面形式的嵌入式密封垫在控制工况,即张开量7 mm、错缝量10 mm的情况下,满足上海深层排水调蓄隧道0.6 MPa的耐水压力要求,且弥补了传统密封垫易从密封垫与混凝土接触面渗漏水的缺陷。此外,通过在密封条两侧设置凹槽,可有效减小密封垫脚部与混凝土间接触应力,减少局部应力集中,保证混凝土管片的完整性,提高接头防水能力。     

Analysis of the Circulation System of a Slurry Shield and the Muck Carrying Ability of a Dredging Pipe北大核心CSCD

The circulation system of a slurry shield is composed of a transportation system and a processing system.For shield construction, correct selection of the circulation system for the slurry shield is directly related to construc-tion speed. Using the Nanjing Yangtze tunnel as an example, the material balance calculation of the circulation sys-tem, sieving effect analysis, and analysis of the muck carrying ability of the dredging pipe are conducted for various strata. The practical results show that above mentioned calculations and analysis method provide a good reference for the proper selection of a slurry separation system and dredge pipe. © 2018, Editorial Office of "Modern Tunnelling Technology". All right reserved.     

Analysis on the Effects of Overloading on the Mechanical Properties of Tunnel Structures in the Silty Ground --A Case Study of Sutong River-crossing GIL Utility Tunnel北大核心CSCD

Based on the Sutong GIL utility tunnel project, which is constructed by the shield machine under the river, and as for the overloading problem at the river bank slope during operating period, the refined threedimensional finite element model was established to study the deformation and cracking characteristics of the tunnel segment structure under different forms of overloading. The evolution laws of section convergence, joint opening and structural stress were analyzed, and the structure damage mechanisms were revealed under conditions of large area loading and local loading. The surface-surcharge control standard was proposed. For the big diameter shield tunneling crossing the silty clay, the research results show that: (1) the deformation failure process is divided into three stages under large area loading condition, taking the design load and compressive yield of rebars inside haunch as the critical points respectively. The first stage is characterized by the elastic stress, the second stage is in plastic state with fracture, and the third stage is accelerating deformation and instability stage. The vertical convergence is 110.5 mm with no opening of joints when rebars are yielded; (2)the deformation failure process under local loading condition is also divided into elasticity, plasticity and instability stages, taking the design load and tensile yield of rebars outside haunch as the critical points respectively. The vertical convergence is 152.6 mm with joint opening of 4.36 mm; (3) the early-warning values of additional stress on the ground under conditions of large area loading and local loading are 110 kPa and 70 kPa respectively. © 2018, Editorial Office of "Modern Tunnelling Technology". All right reserved.     

Soil Body Deformation Caused by Construction of a Double-Line Shield Tunnel with Multiple Factors北大核心CSCD

Considering the influence of many factors (soil loss, frontal additional thrust, the friction force of the shield shell and the additional grouting force), a method for improving the uniform soil body movement model is pro-posed, and a mechanical calculation model is established to study the calculation method for soil body deformation caused by double-line parallel shield driving. Based on the Mindlin solutions of elastic mechanics, the theoretical solutions for soil body deformations caused by the last three factors are calculated; considering the uniform soil body movement model, the theoretical solutions for soil body deformations caused by soil loss are calculated, then the to-tal theoretical solutions for soil body deformations under multiple factors are obtained by means of superposition. The vertical surface settlement, vertical horizontal displacement, and vertical displacements of the soil body at different depths of Hangzhou Metro Line 1 are calculated to analyze the variation laws. Meanwhile the influential factors for horizontal displacement variation are studied. The research shows that with a change of depth, the settlement of the soil body changes within the scope of 10 to 13 m in the horizontal direction near where the maximum settlement occurs;the direction of the horizontal displacement of the soil body changes with a change of the positional relationship be-tween the calculation points and the tunnel; and with an increase of interval J for the two tunnels, the horizontal dis-placement of the soil body of a deep double-line tunnel decreases while the displacement near the surface changes slightly. © 2018, Editorial Office of "Modern Tunnelling Technology". All right reserved.     

全海深双球连接耐压舱的结构设计探索

钛合金耐压球壳被广泛地应用于大深度载人潜水器.但是,由于受到材料强度的限制,若采用成熟的Ti-6Al-4VELI来设计3人型的全海深载人舱,其壁厚将超出很多国家的现有制造能力.为了解决这一矛盾,该文提出了一种新的双球连接的方案,并以中国船级社最新的强度标准作为优化约束条件,用有限元分析法对这种结构形式进行了优化设计.最后,对双球结构方案与传统单球方案作了比较.     

小型双甲板远洋拖网渔船结构优化设计

针对34.5 m双甲板远洋拖网渔船,考虑船东使用后提出的建议,依据《钢质海洋渔船建造规范(2015)》要求对船体结构进行最优化设计,着重对加工间和机舱做到空间最大化,尽可能优化上层结构;利用ANSYS对龙门架选用高强度钢来减小板厚进行分析,加强球鼻结构,减少舷墙构件,做到既符合规范要求又满足渔民实际使用要求。结果表明:优化设计使得机舱空间更合理,结构连续性更好,减轻了上层质量,降低了钢料重心。     

双线自动闭塞区段旅客列车扣除系数计算方法的探讨

本文对旅客列车影响区和非影响区进行了分析，进而确定了非影响区及影响区内可铺画的货物列车数，提出了双线自动闭塞区段旅客列车扣除系数的分析计算方法。