A novel fuzzy logic correctional algorithm for traction control systems on uneven low-friction road conditions

The traction control system (TCS) might prevent excessive skid of the driving wheels so as to enhance the driving performance and direction stability of the vehicle. But if driven on an uneven low-friction road, the vehicle body often vibrates severely due to the drastic fluctuations of driving wheels, and then the vehicle comfort might be reduced greatly. The vibrations could be hardly removed with traditional drive-slip control logic of the TCS. In this paper, a novel fuzzy logic controller has been brought forward, in which the vibration signals of the driving wheels are adopted as new controlled variables, and then the engine torque and the active brake pressure might be coordinately re-adjusted besides the basic logic of a traditional TCS. In the proposed controller, an adjustable engine torque and pressure compensation loop are adopted to constrain the drastic vehicle vibration. Thus, the wheel driving slips and the vibration degrees might be adjusted synchronously and effectively. The simulation results and the real vehicle tests validated that the proposed algorithm is effective and adaptable for a complicated uneven low-friction road.     

考虑复合地基侧摩阻力作用下土中竖向应力解

为了估算新建路基对既有路基影响,以半无限体内Mindlin应力方程解为计算基础,假设复合地基为一个加固整体,对复合地基侧壁摩阻力进行积分,推导复合地基侧摩阻力在土体中引起的附加应力的解析表达式,计算在复合地基作用下距填筑坡脚处一点的土竖向附加应力。     

Experimental study of the airside performance for interrupted fin-and-tube heat exchanger with hydrophilic coating under dehumidifying conditions

The airside heat transfer and friction characteristics of seven interrupted fin-and-tube heat exchangers with hydrophilic coating under dehumidifying conditions are experimented. The effects of number of tube rows, fin pitch and inlet relative humidity on airside performance are analyzed. The test results show that the influence of fin pitch on the friction characteristic under dehumidifying conditions is similar to that under dry surface, and the friction factors decrease slightly with the increase of number of tube rows. The heat transfer performance decreases as fin pitch and number of tube rows increases. The heat transfer performance and the friction characteristic are independent of inlet relative humidity. Based on the test results, heat transfer and friction correlations in terms of the Colburn j factor and Fanning f factor, are proposed to describe the airside performance of the interrupted fin geometry with hydrophilic coating under dehumidifying conditions. The correlation of the Colburn j factor gives a mean deviation of 9.7%, while the correlation of the Fanning f factor shows a mean deviation of 7.3%.     

A model for prediction of the transient rolling resistance of tyres based on inner-liner temperatures

Measurements of rolling resistance in thermal equilibrium of a tyre, like measurements according to ISO 28580, do not allow statements about rolling resistances under other driving conditions. Such statements, however, are necessary to determine the energy consumption in driving cycles. Especially for the proper calculation of electric-vehicle remaining ranges and the selection of the respective driving strategies, the real amount of energy consumption is required. This paper presents a model approach, which by means of only one standardised rolling resistance measurement can be parameterised and, considering the present driving speed and tyre temperature, can predict the respective current rolling resistance.     

全回转导管桨水动力干扰数值预报与分析

为探明串列全回转导管桨水动力干扰问题,基于粘流理论,采用滑移网格方法,开展了均匀来流下两个串列桨在不同偏转角度下水动力性能的数值预报研究,定量分析了不同偏转角度下,上游桨对下游桨水动力的影响,重点关注不同偏转角度时下游桨推力、功率损失及叶片负载的脉动无序性。研究结果表明,在上游桨尾流影响下,上游桨无偏转角度时,下游桨推力损失约70%,上游桨偏转10度时,下游桨推力损失约15%。本文研究结果对动力定位系统控制策略具有指导意义。     

自锁原理在混凝土块体安装机械中的应用

孟加拉Mirsarai海岸防护项目工程护底块体采用100 cm×80 cm×60 cm长方体混凝土块体。在块体生产堆放过程中,须采用夹块机运输,但在安装时由于该护底块未设计吊钩,故无法采用吊车安装,只能用长臂挖机安装液压夹进行夹块安装。液压夹故障率较高,且夹块困难,安放时力度不好控制,容易造成块体间的碰撞损伤。为此,对现有的机械设备做出改进,根据物理学中的静摩擦自锁现象,制作出自锁型夹子。该夹子在夹块时仅仅依靠夹子橡胶复合结构和混凝土块自身重力产生的摩擦力夹紧块体,而安放时仅须旋转挖机斗改变受力钢丝绳来松开块体,无须人员辅助,有效地解决了块体安装过程中机械伤的问题。同时,由于自锁型夹子制作简单、维修方便,因此提高了生产效率、降低了成本。     

排气消声器的传声损失试验研究

汽车NVH作为衡量汽车性能的指标之一,其重要性日益显现。为降低汽车整体噪声,排气噪声作为汽车主要噪声源之一,要优先被考虑。对某型汽车的消声器静态传声损失进行测试与评价,针对其低频性能低的特点,提出改进措施,并对改进后的消声器进行测试。对比两种消声器的试验结果,表明改进后在低频的传声损失更高,平均传声损失更高,达到了预期效果。     

某车排气系统性能的数值模拟及优化研究

为提高某车发动机排气系统的消声量,建立该排气系统的有限元模型,采用三维有限元方法对该排气系统进行声学性能仿真分析,绘制传递损失曲线,发现该排气系统在试验测得的排气噪声频谱能量较高的频段消声量较小,消声性能有待改善.运用流体动力学计算软件fluent对排气系统的流场特性进行分析预测,获得压力损失预测值,以及内部流场的流速...     

沥青路面微表处抗剪性能试验研究

通过直剪试验并结合理论计算对沥青路面微表处的抗剪性能进行研究,研究表明:夏李高温时,微表处的抗剪强度可以抵抗极端不利条件下的车轮剪切力;在最佳油石比±1％的范围内,微表处抗剪强度不会随油石比的增加而减小;界面污染或界面有水会减小微袁处与旧路面的粘结力.     

厚卵石层钻孔灌注桩施工工艺对桩基承载力的影响

结合某汉江特大桥基础的3根试桩资料,研究了在厚卵石层地基条件下不同施工工艺对钻孔灌注桩承载力的影响。结果表明,钻孔灌注桩的成孔工艺、泥浆性能指标、清孔时间及清孔方式都会直接影响桩侧摩阻力和桩端阻力的发挥,同时提出了提高钻孔灌注桩承载力的技术措施及应注意的有关事项。