环氧沥青在大跨径钢桥面粘结层中的应用研究

粘结层材料和施工技术是大跨径钢桥面铺装的关键技术之一。根据某公路大桥桥面铺装粘结层的设计过程和特性，提出了环氧沥青粘结层的设计方法。     

非自由液化场地地基动力性能大型振动台模型试验研究

基于1∶10模型大型振动台试验,研究非自由液化场地的地基动力性能。液化场地条件下,与自由场地基相比,非自由场地地基的自振频率明显加大、动力耗能作用提高较小。土层液化前且在小震输入下,地基动力变形的线性特征较突出,主要表现为对地震波的动力放大作用,加速度反应自下而上逐渐增大;土层完全液化后,地基加速度反应自下而上也逐渐增大,这是由于液化地基的层间剪切运动加快且加快的速率自下而上逐渐增大所致。地基孔压变化主要受两方面因素影响:一是随埋深减小,孔压减小,但孔压比增大;二是离桩距离越近,孔压和孔压比越大。土层液化前,输入波主要峰值过后,自下而上孔压消散逐渐减慢。较大震输入下,自下而上孔压有减小的趋势,但最大孔压比均很快达到液化孔压比;输入波主要峰值过后,孔压消散很缓慢,尤其是孔压消散随埋深减小越来越慢。试验中还出现瞬时负孔压的有趣现象,这也许是由于可液化土层发生瞬时膨胀作用所致。     

软土地基上刚性桩一路堤共同作用分析

针对桩承式路堤工作性状比较复杂、对路堤—桩—土之间共同工作机理的认识还不是十分清楚的问题，建立了考虑土桩路堤变形和应力协调的平衡方程，分析了三者协调工作时路堤、桩、土的荷载传递特性，获得了路堤的土拱效应、桩土荷载分担、桩和土的沉降等结果。将本文的方法与弹塑性有限元计算结果进行了对比，验证了该计算模型的合理性，同时应用所提出的方法，对杭甬高速公路拓宽工程进行了分析。     

软土地基路堤临界高度确定方法探讨

软土地基上高速公路工程建设中存在路堤临界高度的现象,根据国内外已有的文献资料全面总结了路堤临界高度的3种确定方法:实测资料确定法、理论公式计算法和离心模型试验法。在此基础上,根据某高速公路的大量实测数据,利用多元线性回归分析方法,得到了一个路堤临界高度计算的经验公式,探讨了软土地基硬壳层和软土层厚度与路堤临界高度之间的内在联系。     

路堤荷载下管桩复合地基设计理论的试验研究

介绍了管桩复合地基在某高速公路软基试验工程中的应用,并简单分析了其加固效果,进而结合已有的研究成果,提出了一套路堤下刚性桩复合地基的设计理论。通过工程实践表明,该设计理论具有在工程实践中推广运用的价值。     

大跨径连续刚构桥的温度效应分析

以魏家洲特大桥为例,按照我国公路桥涵设计规范、英国BS5400规范、新西兰规范确定不同的计算模式,对大跨径连续刚构桥进行温度效应分析,得出：温度应力在大跨径连续刚构桥整个桥梁设计中占有很大的比重,且采用不同的温度梯度计算模式,所得到的梁内温度应力值相差较大,甚至出现异号的温度应力.     

Fitness-for-purpose assessment of cracked offshore wind turbine monopile

In this paper, the procedure for flaw acceptability assessment is examined through a case study of a semi-elliptical surface crack in an offshore monopile as it grows till it forms a through thickness crack. Using the procedure prescribed in an industrial standard (BS 7910), the fracture ratio, K_r is shown to increase monotonically with increasing crack depth. The load ratio, L_r, is initially insensitive to the crack depth. However, there is a rapid increase in L_r when the crack depth to thickness ratio exceeds 80%. L_r values obtained from detailed 3D FE limit analysis using elastic-perfectly-plastic material behaviour do not exhibit the asymptotic behaviour predicted by BS 7910 as the flaw transitions from deep crack to through-thickness crack. Furthermore, K_r predicted by BS 7910 is shown to be an over-estimation for the typical dimensions of offshore monopiles. The findings suggest that a structure with a deep flaw may be identified as unacceptable based on BS 7910 when it may still possess a non-trivial amount of structural residual life. This is a concern for monopiles where crack growth as a large flaw forms a significant part of the total life.     

多年冻土区钻孔灌注桩施工过程热力特性研究

钻孔灌注桩水化热会暖化冻土引起桩基承载力下降,以桩基水化热在时间与空间上的影响效应为研究目的,结合青藏公路G214沿线查拉坪旱桥桩基观测数据,分析水化热对地温场的扰动范围以及桩周土回冻时间,给出灌注桩18 d内的养护温度。结果表明:水化热对距桩1.95 m以外地温影响微弱;144 d后桩侧温度降至0℃以下,229 d后桩侧温度低于-0.5℃;2 a后桩侧基本回冻至天然地温,此时承载力已达到设计要求。桩基混凝土养护温度前5 d在10℃以上,5~12 d在5℃以上,12~15 d为2℃以上,15~18 d仍高于0℃。通过数值仿真给出混凝土入模温度及桩基施工时间对桩周温度场的影响,模拟结果显示,该区域的灌注桩施工可以在相应规范规定范围内提高混凝土入模温度;灌注桩施工可以在冷季进行,但要做好5 m以上深度桩基混凝土的温控措施。     

内压载荷下X80管道裂纹应力分布规律研究

为了研究内压作用下管道裂纹应力场分布规律,以含有表面裂纹的X80管道为研究对象,对不同形状、不同方向、不同内压、不同尺寸的含裂纹管道进行仿真分析和实验验证。结果表明:裂纹尖端处应力远大于裂纹中心应力。裂纹形状对应力影响作用较小,随着裂纹方向与管道轴向夹角增大,裂纹尖端应力先增大后减小,随着管道内压、裂纹深度、裂纹长度的增大,裂纹尖端处应力随之线性增大。其中,裂纹长度对裂纹尖端应力的影响小于管道内压和裂纹深度。     

A design method of tensile triangles and low transformation temperature weld metal for reduction of stress concentration and residual stress of welded joints

Stress concentration and residual stress have a significant influence on fatigue life of welded joints. In order to reduce the stress concentration of welded joints, a mathematical design method of tensile triangles (MTT) based on bionics was applied to weld shape design. Accordingly, the stress concentration of various weld beads in the corner boxing welded joint and the fillet welded T-joint was dissected using our in-house FEM software JWRIAN. It was found that there existed a large stress concentration in the conventional welded joints, whereas those welded joints with elongated weld bead were accompanied by a lower stress concentration, especially for elongated weld bead with MTT design. Furthermore, among the weld shapes of the corner boxing fillet welded joint, the rectangle shape of weld bead had the minimum stress concentration factor (1.05). For the fillet welded T-joint with MTT design, the stress concentration of weld toe decreased dramatically with the increase of the index of designed shape, but there was a minor difference of stress concentration at weld root between the weld beads with MTT design. In addition, application of low transformation temperature (LTT) weld metal utilizing martensitic transformation to the fillet welded T-joints can produce compressive residual stress at weld toe.