山区公路层间滑移破坏机理分析及对策研究

通过现场调查,初步分析了山区公路沥青路面基面层滑移的主要原因。应用有限元法,对基层和面层之间的剪应力进行计算分析,得出了基面层间剪应力变化的一般规律,认为层间最大剪应力主要取决于面层厚度和荷载条件。在前述计算分析的基础上,利用自行研制的DLG A路面材料剪切仪进行了大量的层间滑移室内模拟试验,考察了不同的层间处理措施、温度、基层类型等因素对层间抗剪能力的影响,提出了防止基面层滑移的技术措施。     

软土地基路堤临界高度确定方法探讨

软土地基上高速公路工程建设中存在路堤临界高度的现象,根据国内外已有的文献资料全面总结了路堤临界高度的3种确定方法:实测资料确定法、理论公式计算法和离心模型试验法。在此基础上,根据某高速公路的大量实测数据,利用多元线性回归分析方法,得到了一个路堤临界高度计算的经验公式,探讨了软土地基硬壳层和软土层厚度与路堤临界高度之间的内在联系。     

路堤荷载下管桩复合地基设计理论的试验研究

介绍了管桩复合地基在某高速公路软基试验工程中的应用,并简单分析了其加固效果,进而结合已有的研究成果,提出了一套路堤下刚性桩复合地基的设计理论。通过工程实践表明,该设计理论具有在工程实践中推广运用的价值。     

混凝土箱梁设计参数对温度效应的影响

在对水府庙混凝土箱梁桥温度场的实测和分析基础上,进行设计参数的研究,包括箱梁翼缘悬臂长度、腹板高度和桥梁轴线方位角对温度场和温度应力的影响,得到最大横向温差与（腹板高度/翼缘悬臂长度）的曲线图.     

大跨径连续刚构桥的温度效应分析

以魏家洲特大桥为例,按照我国公路桥涵设计规范、英国BS5400规范、新西兰规范确定不同的计算模式,对大跨径连续刚构桥进行温度效应分析,得出：温度应力在大跨径连续刚构桥整个桥梁设计中占有很大的比重,且采用不同的温度梯度计算模式,所得到的梁内温度应力值相差较大,甚至出现异号的温度应力.     

沥青混凝土转运车对提高道路施工质量的试验研究

对道路摊铺过程中采用摊铺机直接摊铺作业和采用徐工AT1000A型转运车与摊铺机联合施工作业的试验路面效果进行了对比,分析了摊铺温度场和骨料摊铺效果.结果证明使用沥青混凝土转运车是提高道路施工质量的有效手段.     

多年冻土区钻孔灌注桩施工过程热力特性研究

钻孔灌注桩水化热会暖化冻土引起桩基承载力下降,以桩基水化热在时间与空间上的影响效应为研究目的,结合青藏公路G214沿线查拉坪旱桥桩基观测数据,分析水化热对地温场的扰动范围以及桩周土回冻时间,给出灌注桩18 d内的养护温度。结果表明:水化热对距桩1.95 m以外地温影响微弱;144 d后桩侧温度降至0℃以下,229 d后桩侧温度低于-0.5℃;2 a后桩侧基本回冻至天然地温,此时承载力已达到设计要求。桩基混凝土养护温度前5 d在10℃以上,5~12 d在5℃以上,12~15 d为2℃以上,15~18 d仍高于0℃。通过数值仿真给出混凝土入模温度及桩基施工时间对桩周温度场的影响,模拟结果显示,该区域的灌注桩施工可以在相应规范规定范围内提高混凝土入模温度;灌注桩施工可以在冷季进行,但要做好5 m以上深度桩基混凝土的温控措施。     

Definition of wind blowers for vehicles testing at chassis-dyno facilities using a CFD approach

The need to increase measurement accuracy of fuel consumption and pollutant emissions in vehicles is forcing the market to develop chassis-dyno test cells that reproduce on-road conditions realistically.Air-cooling is key to vehicle performance. It is therefore critical that the design of a test cell guarantees realistic cooling of all vehicle components, as important errors in fuel consumption and emissions measurements may otherwise arise. In a test-room, a blower placed in front of the vehicle supplies the cooling air. While there are some guidelines in the literature for the selection of fans required for emissions measurements for standard driving cycles, the information for designing the air supply system for specific tests in other areas is scarce.New Real Driving Emissions (RDE) legislation will force manufacturers to perform on-road measurements of pollutants. This represents a significant challenge due to the variability of conditions coming from non-controlled parameters. In order to optimize vehicles, different tests are performed in cells equipped with a chassis-dyno where the on-road flow field around the vehicle is reproduced as closely as possible.This work provides some guidelines for the definition of the airflow supply system of chassis-dyno facilities for vehicle optimization tests, based on a CFD analysis of the flow characteristics around the vehicle. By comparison with the solution obtained for a vehicle in real road driving conditions, the exit section of the blower and the distance between the blower exit and the car that best reproduce realistic on-road flow conditions in a test room are determined.     

A design method of tensile triangles and low transformation temperature weld metal for reduction of stress concentration and residual stress of welded joints

Stress concentration and residual stress have a significant influence on fatigue life of welded joints. In order to reduce the stress concentration of welded joints, a mathematical design method of tensile triangles (MTT) based on bionics was applied to weld shape design. Accordingly, the stress concentration of various weld beads in the corner boxing welded joint and the fillet welded T-joint was dissected using our in-house FEM software JWRIAN. It was found that there existed a large stress concentration in the conventional welded joints, whereas those welded joints with elongated weld bead were accompanied by a lower stress concentration, especially for elongated weld bead with MTT design. Furthermore, among the weld shapes of the corner boxing fillet welded joint, the rectangle shape of weld bead had the minimum stress concentration factor (1.05). For the fillet welded T-joint with MTT design, the stress concentration of weld toe decreased dramatically with the increase of the index of designed shape, but there was a minor difference of stress concentration at weld root between the weld beads with MTT design. In addition, application of low transformation temperature (LTT) weld metal utilizing martensitic transformation to the fillet welded T-joints can produce compressive residual stress at weld toe.     

长大货物车适应THDS轴温探测技术的研究

针对不适应THDS轴温探测系统的长大货物车,分析论证了现车轴箱改进方案适应THDS轴温探测的不足,并提出了轴箱优化方案。经计算、试验和装车验证表明,新轴箱可行、有效、安全,满足THDS轴温探测要求,保证了长大货物车运输安全。