船体钢焊接接头的韧性要求与控制

在实验室条件下,以ＦＴＰ准则为判据,对潜艇耐压壳体母材韧性进行了测评,并重点就焊接接头性能是否符合壳体抗爆要求的问题进行了小试样实验研究和理论分析,最后根据有关试验结果给出了接头质量控制的合理焊接工艺参数。     

某下穿通道快速化预制拼装工艺总体设计方案

随着国家城市化进程的不断加快,传统现浇工艺存在着施工质量相对较差、对周边环境影响较大、劳动力成本不断上升等一系列问题,与国家提出的高质量发展目标存在一定差距,为此国家从政策方面开始推行预制拼装工艺。以某斜交下穿通道工程采用预制拼装工艺为例,从结构分块、接缝形式及防水、吊点布置等关键环节进行了系统性的研究与探讨,提出了一整套的设计方案,为工程的建成提供了有力的技术支撑,同时也为类似工程提供了有意义的参考借鉴。     

The impact of structural flexibilities of wheelsets and rails on the hunting behaviour of a railway vehicle

The hunting motion of a passenger coach is investigated using a multibody system in which the wheelsets and the rails can be modelled as flexible bodies. By comparing the results for different model variants, in which the structural flexibilities of the wheelsets and of the rails are either taken into account or neglected, the impact of the flexibilities is analysed. It turns out that the flexibilities of both the wheelsets and the rails have a significant impact on the hunting behaviour by increasing the lateral motions of the wheelsets and lowering the critical speed. In order to investigate the impact of the flexibilities under different operating conditions, the calculations are carried out for track geometries using different rail profiles (60E1, 60E2) and different rail cants (1:40, 1:20) and for different values for the friction coefficient (0.25…0.4) at the wheel–rail contact. The results show that the influence of the flexibilities is the strongest for high lateral forces, which occur e.g. for contact geometries leading to high hunting frequencies and for high values of the friction coefficient. The results also show in some cases a strong impact of the flexibilities on the position of the wheel–rail contact on the running surface of the rail, which is of particular interest with respect to wear simulation.     

浅谈沥青混合料路面接缝的施工方法

根据施工经验介绍了沥青混合料路面接缝的施工方法.     

长寿柔性基层沥青路面的极限应变

长寿柔性路面设计通常采用沥青层底极限拉应变和土基顶部极限压应变作为控制指标。现阶段极限应变指标参照室内试验结果确定，且数值相对固定。而现场路面结构层应变响应值受结构厚度、荷载、环境作用（温度及老化）等因素的影响，在服役过程中不断演化。以2条服役超过35年的柔性路面结构（屯门公路与吐露港公路）为基础，分析了不同服役阶段路面结构层在不同荷载、环境作用下的极限应变响应，探讨了柔性路面极限应变的大概范围。研究结果表明：在初始服役状态下，屯门公路高温状态下沥青层底的极限拉应变为376×10^-6，土基顶部极限压应变为562×10^-6；低温状态下上述极限应变分别降为87×10^-6，249×10^-6；吐露港公路高温状态下沥青层底、土基顶部极限应变分别为149×10^-6，324×10^-6，低温状态下上述应变分别降为50×10^-6，156×10^-6。在经过长期服役后，老化状态下2类路面沥青层底拉应变及土基顶部压应变均大幅降低。屯门公路在使用36年后，某些路段出现零星的疲劳破坏，而吐露港公路则没有发现疲劳破坏。极限应变计算结果表明，路面关键位置的应变受荷载、沥青层厚度、温度和沥青层老化状态等多因素的影响。因此，在进行长寿柔性基层路面设计中，荷载、沥青层厚度、温度及沥青层老化状态等因素都应该考虑在内。     

Influence of polygonal wear of railway wheels on the wheel set axle stress

The coupled vehicle/track dynamic model with the flexible wheel set was developed to investigate the effects of polygonal wear on the dynamic stresses of the wheel set axle. In the model, the railway vehicle was modelled by the rigid multibody dynamics. The wheel set was established by the finite element method to analyse the high-frequency oscillation and dynamic stress of wheel set axle induced by the polygonal wear based on the modal stress recovery method. The slab track model was taken into account in which the rail was described by the Timoshenko beam and the three-dimensional solid finite element was employed to establish the concrete slab. Furthermore, the modal superposition method was adopted to calculate the dynamic response of the track. The wheel/rail normal forces and the tangent forces were, respectively, determined by the Hertz nonlinear contact theory and the Shen–Hedrick–Elkins model. Using the coupled vehicle/track dynamic model, the dynamic stresses of wheel set axle with consideration of the ideal polygonal wear and measured polygonal wear were investigated. The results show that the amplitude of wheel/rail normal forces and the dynamic stress of wheel set axle increase as the vehicle speeds rise. Moreover, the impact loads induced by the polygonal wear could excite the resonance of wheel set axle. In the resonance region, the amplitude of the dynamic stress for the wheel set axle would increase considerably comparing with the normal conditions.     

既有线提速改造中S700K转辙设备调试方法研究

探讨在既有线提速改造施工过程中,对S700K转辙设备的调试方法,提高该型转辙设备的调试效率,有效缩短联锁试验时间.     

外墙外保温系统的抗火问题研究

该文阐述了外墙外保温系统抗火的重要性,并分析国内外相关技术的发展现状。在此基础上,从保温材料的选择、节点构造、防火构造等三个方面,对现有外墙外保温系统抗火的要求进行了分析与探讨,并对施工提出了建议。     

复合材料螺栓连接结构数值模拟研究

在实际工程中,复合材料结构连接方式常采用机械连接形式(螺栓或铆钉)来连结复合材料构件和金属构件,而其中尤以螺栓连接更为常见.如何运用有限元软件模拟螺栓连接结构是仿真计算的关键.本文采用ANSYS软件,建立了复合材料螺栓连接结构的三维有限元模型,采用不同的边界处理方法对该结构进行数值模拟,得到复合材料螺栓孔处的载荷,并将数值计算结果与试验数据比较,探求出了该结构螺栓孔处载荷数值模拟方法.采用接触+耦合的边界处理方式不仅能较准确的模拟复合材料螺栓连接结构,而且计算时间远小于完全采用接触时的计算时间,大大提高了工作效率.