深海耐压舱室寿命估算

耐压舱室在深海中下潜一定深度和收回过程中,受到的水压可以简化为底周期循环应力。在该循环应力作用下,根据断裂力学理论和结构损伤-安全设计原理,以临界裂纹尺寸的设计方法结合具体工程应用案例计算设备寿命,得出在一定初始裂纹深度和长度下设备的理论使用次数。采用计算机程序实现迭代计算。此应用案例在疲劳的可靠性计算中具有一定的工程指导意义。     

柴油机掺烧气体燃料的低负荷性能试验研究

采用试验方法研究柴油机低负荷工况掺烧LPG和CNG燃料的经济性和排放性能,探讨气体燃料掺烧比例、喷油提前角和压缩比对低负荷性能的影响,研究表明,柴油机低负荷掺烧气体燃料会导致燃烧室温度下降、燃烧不良、经济性下降和HC排放急剧增加,因此,减少气体燃料掺烧比例、增大喷油提前角、减小喷油器的喷孔直径和适当增大压缩比,有利于改善柴油机掺烧气体燃料的低负荷性能。     

A stochastic optimization approach for the selection of reflective cracking mitigation techniques

PurposeIn Hot Mix Asphalt (HMA) overlays, the existing cracks in the underlying pavements can propagate upward to the new added overlay and may cause Reflective Cracks (RC). These cracks allow water infiltration to the underlying layers and causes further moisture damage as well as weakening the unbound layers. Over the years, several methods have been developed for mitigating the RCs. This study aims to investigate the current reflective cracking mitigation methods and develop a methodology for the selection of appropriate mitigation technique. The developed model is then applied to a case study in the state of Florida.MethodTo accomplish this goal, a nationwide literature review was conducted to better understand the current in practice methods in the United States. Moreover, a life cycle cost analysis (LCCA) in five different road types was performed to find the annuity of roadway rehabilitation for each of the mitigation methods. The uncertainty in the LCCA results is represented using Exploratory Modeling and Analysis (EMA) method. Then through a Multi Criteria Decision Making (MCDM) model, a stochastic optimization model was developed to find the appropriate reflective cracking mitigation solution under Florida’s climate and road conditions, based on different cost and performance weights.ResultsBased on the available data for the state of Florida, the LCCA results indicate that the annuity of maintaining the roadway with Fabrics and ISAC are lower compared to other methods. However, the results of stochastic optimization model reveal that while looking at the performance and cost at the same time, different methods would be more feasible. For instance, while the cost of the used method does not matter at all and only performance matters, STRATA® is more probable to be the appropriate mitigation technique. The findings of this research are critical for decision makers to better understand the most cost-effective mitigation technique in different conditions.     

Development of a driving cycle for Colombo,Sri Lanka: an economical approach for developing countries

Financial constraints and lack of availability of traffic‐related information significantly hinder the development of driving cycles in developing countries. This paper proposes an economical, practical, accurate methodology for the development of driving cycles, including the development of a driving cycle for Colombo, Sri Lanka. The proposed methodology captures regional traffic and road conditions and selects a model that represents the collected data sample with minimum available traffic‐related information. Existing methods were modified for route selection by dividing routes into links using nodes or physical junctions to minimize the number of trips required for data collection. Speed–time data for respective links were used to reconstruct speed–time profiles of identified origin–destination pairs. The on‐board method was used for data collection, and the Markov chain theory was used to develop a transition probability matrix of state changes. An additional matrix was introduced to the existing method to improve model representativeness to the collected data sample. Copyright © 2016 John Wiley & Sons, Ltd.     

管道疲劳寿命的可靠性分析

针对管道的疲劳失效分析,以概率论为基础,结合确定性的疲劳断裂力学估算方法,推导了管道的疲劳裂纹扩展寿命的计算公式.考虑到主要评定参数:初始裂纹尺寸、工况载荷、断裂韧性、机械强度、系数等的不确定性和随机性,应用蒙特卡罗模拟法对这些具有某种特定分布的随机变量进行了随机抽样计算.并利用数值积分法编制了计算机程序,求出在一定可靠度和置信度下的疲劳寿命,并与理论计算方法求得的疲劳寿命进行了比较.还比较了不同初始裂纹尺寸和断裂韧性对疲劳寿命的影响,并给出了算例.分析结果表明:蒙特卡罗模拟法真实地反映评定参数客观存在的不确定性,克服了确定性评定方法的缺点,具有良好的工程指导意义.     

Multi-objective optimization for asphalt pavement maintenance plans at project level: Integrating performance,cost and environment

Traditionally, asphalt pavement maintenance mainly considers pavement performance and cost and largely ignores the environment while substantial amount of environmental burdens are released in the process. In this study, a multi-objective optimization model was developed integrating the three elements in order to optimize the asphalt pavement maintenance plans at the project level. Pavement performance element was decided as the multiplier of pavement serviceability index and traffic volume. Cost element was represented by the net present value, including components of agency cost, vehicle operation cost and salvage value. Environmental element, integrating energy consumption, global warming potential, acidification potential and respiratory effects potential, was measured by the life cycle assessment model. A hypothetic asphalt pavement maintenance case study was conducted using the developed multi-objective optimization model and harvested 103 sets of feasible combinations of maintenance plans, each of which is non-dominated by the others. Trade-offs analysis was performed among the three objectives and visualized in both two- and three-dimension forms. It is found there is an opportunity of reducing the cost and environmental impacts to 80.3% and 77.8% and increasing the pavement performance to 146.6% compared to the base case. However, they are mutually compromised and cannot be reached simultaneously. The developed model reveals the quantitatively interactive relationship of the three objectives and helps optimize the asphalt pavement maintenance plans.     

Optimal bus fleet management strategy for emissions reduction

Transportation is a major cause for environmental degradation via exhaust emissions. For many transit-oriented metropolitan areas, bus trips often constitute a sizeable mode share. Managing the bus fleet, in particular updating buses to comply with the newer emissions standards, therefore, can have a substantial impact on transportation-induced air quality. This paper presents the approach of remaining life additional benefit–cost (RLABC) analysis for maximising the total net benefit by either early-retiring or retrofitting the current bus fleet within their lifespans. By referring to the net benefits for different bus types estimated by RLABC analysis, the most beneficial management scheme for the current bus fleet can be identified. Optimal bus fleet management (BFM) models based on the RLABC analysis for the operator and the government are developed. Then a government subsidy plan is produced to achieve win–win solutions, which will offer efficient and flexible management schemes. To illustrate the approach, the largest bus company in Hong Kong, which carries more than 23% of the total trips in Hong Kong, is taken as a case study example. Instead of adopting a fixed retirement plan, such as replacing buses at the age of 17 as is currently practised, the proposed method develops an optimal BFM scheme that progressively phases out buses or retrofits them. This study produces promising results to demonstrate the large benefit of this approach for optimal bus fleet management.     

Environmental impacts of public transport systems using real-time control method

Public Transport (PT) systems rely more and more on online information extracted from both operator’s intelligent equipment and user’s smartphone applications. This allows for a better fit between supply and demand of the multimodal PT system, especially through the use of PT real-time control actions/tactics. In doing so there is also an opportunity to consider environmental-related issues to approach energy saving and reduced pollution. This study investigates and analyses the benefits of using real-time PT operational tactics in reducing the undesirable environmental impacts. A tactic-based control (TBC) optimization model is used to minimize total passenger travel time and maximize direct transfers (without waiting). The model consists of a control policy built upon a combination of three tactics: holding, skip-stops, and boarding limit. The environmental-related measure is the global warming potential (GWP) using the life cycle assessment technique. The methodology developed is applied to a real life case study in Auckland, New Zealand. Results show that TBC could reduce the GWP by means of reduction of total passenger travel times and vehicle travel cycle time. That is, the TBC model results in a 5.6% reduction in total GWP per day compared with an existing no-tactic scenario. This study supports the use of real-time control actions to maintain a reliable PT service, reducing greenhouse gas emissions and subsequently moving towards greener PT systems.     

Vehicle electrification in a developing country: Status and issue,from a well-to-wheel perspective

The increase of public attention, scientific research and political interest in environmental problems associated with transportation has provided the motivation for re-invention of electric vehicles. However the usage of grid-dependent EVs with a high-carbon electricity grid might produce more damage to the environment. This study aims to provide an environmental impact comparison of ICEVs, HEVs and EVs during their usage cycle, by modeling their energy consumption (electricity or fuel) and the supply chains of the supplied energy, (well-to-wheel) based on a life cycle assessment. The results show that running EVs with the existing mixed sources of electrical energy produce larger impacts on the environment 60% of the time; when compared to HEVs. When compared to ICEVs, EVs produce a larger environmental impact on 7 out of 15 environmental impact categories. Overall the environmental impacts of EVs are substantial based on the well-to-wheel analysis. It will continue to be so if no change is made to the methods of electricity generation in the near future. Given that the environmental profile of EVs is linked with the existing national electricity generation mix, the national electricity supply must be made cleaner before the electrification of the urban transport system.     

基于发动机台架考核方法的气缸盖高周疲劳特性研究

依据发动机台架考核规范,运用疲劳强度理论,对某铸铁气缸盖进行高周疲劳强度评估。明确温度和应力随考核工况改变的变化行为,研究气缸盖各区域受工作载荷的影响状况,为缸盖寿命评估模型提供载荷边界。结合疲劳理论,在考虑材料修正的基础上进行了疲劳特性分析和损伤状况分析。分析表明,气缸盖各区域的疲劳安全系数均大于1,视为安全,但冷却钻孔区域的安全裕度较小。