Definition of wind blowers for vehicles testing at chassis-dyno facilities using a CFD approach

The need to increase measurement accuracy of fuel consumption and pollutant emissions in vehicles is forcing the market to develop chassis-dyno test cells that reproduce on-road conditions realistically.Air-cooling is key to vehicle performance. It is therefore critical that the design of a test cell guarantees realistic cooling of all vehicle components, as important errors in fuel consumption and emissions measurements may otherwise arise. In a test-room, a blower placed in front of the vehicle supplies the cooling air. While there are some guidelines in the literature for the selection of fans required for emissions measurements for standard driving cycles, the information for designing the air supply system for specific tests in other areas is scarce.New Real Driving Emissions (RDE) legislation will force manufacturers to perform on-road measurements of pollutants. This represents a significant challenge due to the variability of conditions coming from non-controlled parameters. In order to optimize vehicles, different tests are performed in cells equipped with a chassis-dyno where the on-road flow field around the vehicle is reproduced as closely as possible.This work provides some guidelines for the definition of the airflow supply system of chassis-dyno facilities for vehicle optimization tests, based on a CFD analysis of the flow characteristics around the vehicle. By comparison with the solution obtained for a vehicle in real road driving conditions, the exit section of the blower and the distance between the blower exit and the car that best reproduce realistic on-road flow conditions in a test room are determined.     

A design method of tensile triangles and low transformation temperature weld metal for reduction of stress concentration and residual stress of welded joints

Stress concentration and residual stress have a significant influence on fatigue life of welded joints. In order to reduce the stress concentration of welded joints, a mathematical design method of tensile triangles (MTT) based on bionics was applied to weld shape design. Accordingly, the stress concentration of various weld beads in the corner boxing welded joint and the fillet welded T-joint was dissected using our in-house FEM software JWRIAN. It was found that there existed a large stress concentration in the conventional welded joints, whereas those welded joints with elongated weld bead were accompanied by a lower stress concentration, especially for elongated weld bead with MTT design. Furthermore, among the weld shapes of the corner boxing fillet welded joint, the rectangle shape of weld bead had the minimum stress concentration factor (1.05). For the fillet welded T-joint with MTT design, the stress concentration of weld toe decreased dramatically with the increase of the index of designed shape, but there was a minor difference of stress concentration at weld root between the weld beads with MTT design. In addition, application of low transformation temperature (LTT) weld metal utilizing martensitic transformation to the fillet welded T-joints can produce compressive residual stress at weld toe.     

舰船加筋板局部强度评估中的总纵应力折减系数研究

舰船加强筋尺寸的合理确定一直是结构设计中的热点问题。本文综合考虑总纵弯曲应力和局部载荷的相互作用,研究加强筋的许用应力折减系数(C_s)的影响因素与合理取值方法。通过分析加强筋的力学模型、对比不同规范中的C_s取值,以及用非线性有限元软件Abaqus计算一系列加筋板模型,拟合C_s曲线并与规范对比,并验证剖面对称性和局部载荷作用方向对C_s取值的影响方式,丰富了舰船局部强度校核方法的技术背景,为板架设计、舰船三维局部校核程序开发提供借鉴。     

25t轴重荷载作用下隧底脱空区域受力特性分析

为了研究在役铁路隧道在通车之后隧底脱空病害的问题,采用有限元理论,建立隧道脱空区域在围岩压力与25 t轴重列车动载作用下的数值计算模型,主要研究80 cm与40 cm脱空宽度分别距隧道中心线0,80 cm与160 cm时脱空区域的受力特性。结果表明:在围岩压力下,脱空区域中线上壁和外侧顶角混凝土中产生拉应力及内侧顶角中产生压应力,其中压应力对脱空的宽度更为敏感;同时施加列车动载作用时,脱空区域上壁出现了竖向动应力与横向拉应力,得到了脱空区域力学指标的最大响应值及其出现的具体位置,宽度的增加对脱空区上壁横向拉应力更为显著,上壁横向拉应力增幅超过200%,竖向动应力增幅达50%。因此,隧底脱空区周围应力分布复杂,拉应力与压应力在脱空区域同时存在,应力突变严重,对脱空现象应及时组织处理。     

含碎石化层的沥青加铺路面结构分析

利用ABAQUS有限元软件建立了含碎石化层的沥青加铺路面结构模型,研究土基、旧路基层与碎石化层模量以及碎石化层和加铺层厚度对含碎石化层沥青加铺层路面结构的力学响应的影响,确定碎石化模量的控制范围.结果表明,荷载作用中心点及附近一定区域,沥青加铺层层底受拉;沥青加铺层层底拉应力对土基模量、旧路基层模量、碎石化层厚度不敏感,但当碎石化层模量较小(接近300MPa)或加铺层厚(大于20cm)时层底拉应力均较大,在重载作用下更大.因此碎石化道路必须验算沥青层层底拉应力指标.为使沥青层层底拉应力峰值不至于过大甚至超过容许拉应力,使得受拉区域控制在一定范围以内,同时为降低加铺层竖向剪应力及土基顶面压应变,并达到防治反射裂缝的效果,碎石化层的模量宜控制在500～1000MPa.     

某型直流充电柜温度场仿真

对某型直流充电柜满负载工况下温度场进行仿真,根据实验测量数据验证仿真结果准确性,成功完成了对充电柜温度场的建模仿真工作,并实现对初始模型的简化,为对整个充电站进行温度场建模仿真奠定了基础。     

Analysis of cross effect on inherent deformation during the line heating process – Part 1 – Single crossed heating lines

This paper describes the effect of previous heating on inherent deformation by a subsequent heating line, more specifically, the case of two heating lines intersecting (crossing) each other. The paper has been divided into two parts. In the first part, the case of single crossed heating lines is studied in detail. The second part of the paper, discusses the case of more than one crossed heating lines. The novelty of the work lies in revealing the cross effect and how, factors such as, for example, the heating condition and the plate geometry, influence the resulting inherent deformation of crossed heating. In addition, relationships to easily get these influences are provided. The results are suitable for a wide range of heating conditions and plate thickness.     

横梁端部节点优化

通过有限元计算,对比几种常见的横梁端部连接方式,综合考虑结构整体强度、钢材使用量、舱室空间利用率、施工便利性等方面的影响因素,确定较优的连接过渡方式和过渡结构的参数尺寸,为船舶设计横梁端部节点形式的确定提供参考。     

大城市中小学周边地区交通拥堵问题分析与解决策略

交通拥堵已经成为我国大城市的一种社会问题,它与每一个人都息息相关,如何更好地处理这种问题,使其减少对人们出行的影响,成为值得每一个人思考的问题。针对大中型城市中的交通拥堵其中的一种现象进行深入的剖析,系统介绍交通拥堵的成因,有针对性地提出如何改善中小学周边地区交通拥堵现象的一些观点和做法。     

Commuting and wellbeing: a critical overview of the literature with implications for policy and future research

ABSTRACT

This review provides a critical overview of what has been learnt about commuting’s impact on subjective wellbeing (SWB). It is structured around a conceptual model which assumes commuting can affect SWB over three time horizons: (i) during the journey; (ii) immediately after the journey; and (iii) over the longer term. Our assessment of the evidence shows that mood is lower during the commute than other daily activities and stress can be induced by congestion, crowding and unpredictability. People who walk or cycle to work are generally more satisfied with their commute than those who travel by car and especially those who use public transport. Satisfaction decreases with duration of commute, regardless of mode used, and increases when travelling with company. After the journey, evidence shows that the commute experience “spills over” into how people feel and perform at work and home. However, a consistent link between commuting and life satisfaction overall has not been established. The evidence suggests that commuters are generally successful in trading off the drawbacks of longer and more arduous commute journeys against the benefits they bring in relation to overall life satisfaction, but further research is required to understand the decision making involved. The evidence review points to six areas that warrant policy action and research: (i) enhancing the commute experience; (ii) increasing commute satisfaction; (iii) reducing the impacts of long duration commutes; (iv) meeting commuter preferences; (v) recognising flexibility and constraints in commuting routines and (vi) accounting for SWB impacts of commuting in policy making and appraisal.