舰用主汽轮机汽缸动刚度分析研究

为准确计算主汽轮机低压缸整体结构的动刚度,选取最能反映模型整体位移的低压缸底部中心处为单位激振力的加载点,考虑模型在单位激振力作用下的动态响应,并与在前后轴承座处加载单位激振力时的动态响应进行对比分析。研究表明,在低压缸底部中心处加载激振力能够较好地反映整体模型的振动特性,能较精确地得到整体模型的动刚度,是可行且有效的。     

船用主汽轮机汽缸静刚度分析研究

针对船用主汽轮机低压缸静刚度的仿真研究考虑温度场和压力场等复杂环境研究较少的现象,为准确计算主汽轮机低压缸结构的静刚度,对考虑温度场、压力场作用的低压缸正车和倒车工况时的静刚度进行研究,并与仅考虑自身重力的设备静刚度进行对比分析.研究表明,温度场、压力场对加载部位结构的响应特性有很大影响,对低压缸整体结构也有一定程度的影响,为更加准确地模拟真实设备,在进行设备的静刚度分析时应该给予考虑.     

船舶汽轮机末级叶片改进设计

对于船舶汽轮机而言,末级叶片变工况特性对整个机组性能具有重要的影响.指出了某型船舶汽轮机末级叶片在低负荷工况时出现的根部负反动度以及脱流、回流问题;给出了叶型改进方案,通过强化叶型、合理控制叶片根部反动度等手段,降低低负荷工况下末级叶片根部的回流,提高叶片抗振强度,改善流动状况,提高机组性能.     

可变截面涡轮增压瞬态性能仿真研究

为研究可变截面涡轮喷嘴开度对发动机的性能影响,建立GT-power和MATLB/Simulink联合仿真模型。采用GT-power软件建立的TBD234V12可变截面涡轮增压柴油机仿真模型研究发动机稳态性能,联合MATLB/Simulink软件建立的可变截面涡轮增压柴油机控制模型,对发动机瞬态性能进行仿真计算。结果表明:在发动机瞬态工况下,可变截面涡轮增压系统可以明显改善常规增压柴油机的动力性、经济性和动态响应特性,并且有效降低增压柴油机的时滞性,涡轮迟滞时间的降幅约为30%。     

某型气垫登陆艇燃气涡轮发电机组弹性轴断裂分析

介绍了气垫登陆艇的故障现象,通过故障现象分析,对故障进行了定位,通过对故障件进行理化分析、金相组织分析、断口分析,设计图样与实物的制造符合性分析,最后采用实例建模进行了强度校核,得出某型气垫登陆艇燃气涡轮发电机组弹性轴断裂的故障模式。     

南海风浪条件下Spar式浮式风机平台的构型及参数

使用WAMIT软件建立了OC3-Hywind Spar式浮式风机模型,联合FAST软件计算了浮式风机在不同工况下的幅值响应算子;结合为南海海域波浪条件优化后的JONSWAP谱,对浮式风机进行了不同工况下的响应谱分析及最大响应值计算;进一步阐述了浮式平台结构构型参数的变化对整体结构在南海相应工况下的运动影响。     

Mechanism of Tunnel Water Inflow Caused by Bending Failure of a Waterproof Dike Based on a Circular Thin Plate Mechanical Model北大核心CSCD

Water bursts during tunnel construction endanger construction, and it is therefore necessary to reserve a waterproof dike with the required thickness to avoid water bursts and to take reinforcement of the dike and treatment of the structure liable to trigger a water burst. Using the water burst at K5+398 of the Mingyueshan tunnel of the Shanghai-Chengdu expressway as an example, and considering the type of tunnel section and the upright mudstone of the dike, the waterproof dike at the work face is simplified as a round thin plate. A formula for the calculation of a minimum safety thickness for the critical waterproof dike is deduced by analyzing the force applied on the water-proof dike, and the minimum safety thickness for the water burst section at K5+398 of the Mingyueshan tunnel is cal-culated. The numerical simulation analysis demonstrates the critical thickness of waterproof dike at K5+398 of the Mingyueshan tunnel is 1.4-1.55 m, and the calculated water inflow and water burst basically agree with the actual condition. © 2018, Editorial Office of "Modern Tunnelling Technology". All right reserved.     

MTMD to increase fatigue life for OWT jacket structures using Powell's method

The Powell's method was developed to determine the optimal stiffness and damping of multi-tuned mass dampers (MTMD) in offshore wind turbine (OWT) support structures under fatigue loads. Numerical examples indicated that the Powell's method results are always better than those using MTMD formulations. With the exception of the blade passing (3P) frequency, it was found in this work that a positive integer (n) multiple of the 3P frequency will also result in a large wind-induced vibration, which can be excited by the frequency of the first structural vertical rotation mode and will cause significant fatigue damage. The first translation mode TMD installed at the tower top is efficient to increase fatigue life at the tower and brace connections, but it cannot reduce fatigue damage at the column and brace connections below the platform. The second translation mode TMD can reduce fatigue damage resulting from large wave loads and thus increase the fatigue life of the braces and columns. The mode-3 TMD with a reduction in the 3(3P) vertical rotation can effectively increase the fatigue life of the braces and columns. Thus, the appropriate use of these TMDs can be effective for the fatigue problem of OWT support structures.     

燃气向心透平的非定常流动特性研究

以燃气为工质的向心透平常用于微型燃气轮机系统中,有着重要的工程应用价值。本研究关注燃气向心透平的非定常流动特性,基于一台功率等级为1MW,转速为30000rpm的燃气向心透平,首先进行了热力设计,得到了其关键位置的燃气工质热力参数及透平的模型尺寸。其次基于三维粘性数值模拟计算的方法,采用SST k-ω湍流模型及六面体结构化网格在商用软件CFX中对燃气向心透平进行了定常与非定常气动计算,详细分析了其气动特性及非定常流动状况。最终,分析了这一燃气向心透平的非定常气流激振力在时域及频域分布,并准确评估了其流量、扭矩、功率及效率等关键参数。     

垂直水幕作用下扩建地下水封油库布局方式研究

为研究垂直水幕对扩建地下水封油库布局方式的影响,以某大型地下水封洞库分期建设工程为依托,采用有限元数值模拟方法,对有、无垂直水幕条件下扩建洞库的布局方式进行研究。研究结果表明： 1）当两期洞库间距较小时,在两期洞库之间设置垂直水幕可有效削弱拟建洞库对已建洞库水封可靠性的影响,随两期洞库间距的增加,垂直水幕的影响性逐渐减弱; 2）拟建洞库轴线方向对水封可靠性的影响受地形等条件的影响较大,在两期洞库之间设置垂直水幕对水封可靠性的影响较小; 3）随拟建洞库埋深的增加,拟建洞库的水封可靠性逐渐增强,已建洞库的水封可靠性却呈逐步减小趋势,在两期洞库之间设置垂直水幕可有效减小埋深对两期洞库水封可靠性的影响。