一种确定高圆簧横向刚度的有效方法

文中将高圆簧简化为等截面弹性直杆，导出高圆簧横向刚度计算式，并用试验结果进行修正，提出高圆横向刚度分析方法。理论分析和试验结果表明：高圆簧横向刚度的大小取愉于高圆簧的自由高度和工作高度，即由其结构几何参数和工作载荷决定。按文中方法确定的高圆簧横向刚度理论值与试验结果间的最大误差不超过１０％，满足工程理论分析要求。     

沥青混凝土搅拌机燃用重渣油的尝试

为降低沥青混凝土搅拌机的生产成本,采用ZZR重渣油燃烧机替代柴油燃烧机取得了很好的经济效益,给出了燃渣油时渣油含水及油路阻塞的判断方法,并介绍了出现故障的排除方法.     

深海超高压环境模拟容器裂纹评定

深海超高压环境模拟容器用于模拟水下压力环境,其容器壁上承受反复载荷,容易产生疲劳裂纹.疲劳裂纹扩展是影响其断裂的主要因素.本文旨在分析半椭圆裂纹在老化的深海超高压环境模拟容器中的扩展行为,评估容器的安全性,因此对材料20MnMoNb钢的裂纹扩展特性进行了试验研究,首先考虑三角形和梯形加载情况,通过比较两组实验结果,考察了其材料对保载时间的敏感性.采用基于统一的裂纹扩展率模型的三维有限元方法进行了疲劳裂纹扩展计算,并通过CT试样的一组数值和实验结果进行了验证,最后建立了不同初始尺寸、展弦比和倾角的裂纹有限元模型,并根据裂纹在容器内壁的容许深度准则,计算了容器的剩余寿命.其分析结果可为深海超高压环境模拟容器可靠性评估提供参考.     

Centrifuge modelling of pipe-soil interaction in clay with crust layer

Seabed in regions, such as the Gulf of Guinea and North West Shelf of Australia, may exhibit a crust layer where the undrained shear strength can be an order of magnitude higher than that of the immediately underlying sediment. This can complicate design of steel catenary risers, where fatigue depends on the cyclic vertical stiffness of the pipe-soil interaction. Potential punch-through of the riser into the underlying soft soil may invalidate design assumptions based on the pipe-soil stiffness within the crust layer. The long-term evolution of pipe-soil stiffness within the crust layer, which exhibits similar properties to an over-consolidated soil, is also poorly understood. This paper describes centrifuge model tests undertaken in a clay sample with a crust layer, simulating the punch-through process of a pipe under load control and investigating the pipe-soil stiffness during long-term cyclic loading tests under displacement control. Results confirm that the potential for punching-through the crust layer depends strongly on the relative ratio of pipe diameter to crust layer thickness. The long-term evolution of pipe-soil stiffness showed a steady increase after an initial remoulding stage in contractile soils (normally consolidated and lightly over-consolidated), but a steady reduction in the heavily over-consolidated, more dilatant, crust. The magnitude of pipe-soil stiffness changes (during both remoulding and reconsolidation) is governed by the over-consolidation ratio of the soil and the amplitude of the cyclic displacements. This study provides insights on the relevant cyclic stiffness to consider when assessing SCR fatigue life in over-consolidated soils and soils exhibiting a superficial crust layer.     

A study on the stability of a motorcycle wheel–swingarm suspension with chain transmission

The present study describes a possible driving mechanism for a self-excited oscillation observed in motorcycle dynamics, often referred to as chatter. This phenomenon, affecting the performance of road racing motorcycles, has been simulated in straight running braking manoeuvres with multibody motorcycle models. It involves rear suspension bounce and driveline oscillation in the frequency range between 17 and 22?Hz. A simplified model of a motorcycle rear suspension with chain transmission is proposed and its stability in equilibrium configurations is studied via eigenvalue analysis. The sensitivity with respect to all its governing parameters is analysed by means of stability maps and the self-excitation mechanism is explained with the aid of energy balance analysis and phase diagrams. It is found that the key role for the instability onset is played by the gradient of the nonlinear characteristic slip function of the tyre.     

基于灰色残差GM（1，1）模型的道路交通量预测的研究

道路交通体系是一个多因素、多层次、多目标的复杂系统。其中交通量信息系统具有明显的层次复杂性,结构关系的模糊性,动态变化的随机性,指标数据的不完全和不确定性。由于技术方法、人为因素、自然环境变化的影响,造成各种数据误差、短缺甚至虚假现象,系统的作用机制不明确,系统的状态、结构、边界关系难以精确描述,属于典型的灰色系统。在作量化、模型化、实体化研究时,能作为反映系统主要动态特征的数据是很少的。由于环境对系统的干扰,系统信息中原始数据序列往往呈现离乱情况,离乱数列即为灰色数列或称灰色过程,灰色理论利用那些较少的或不确切的表示系统行为特征的原始数据序列作生成变换后建立微分方程,对灰色过程建立的模型称为灰色模型（Greymodel）,简称GM模型。本文从理论上介绍了GM（1,1）模型和灰色残差GM（1,1）模型建立的一般过程,然后将其应用于交通量预测的实际例子中。预测结果表明,该方法是可行的。     

中国铁路提速后技术进步对产出贡献的测算

选取我国铁路提速后1997~2007年间的相关数据,采用基于科布——道格拉斯生产函数的Solow余值法,将有限分布滞后模型和半参数回归模型引入计算模型,对数据进行拟合,计算得到铁路提速后技术进步、固定资本投入以及人力资本投入对产出的贡献率,并根据计算结果提出促进我国高速铁路建设的相关对策建议.     

焊接顺序对高速列车侧墙焊接残余应力的影响

按实际加工工艺,基于有限元软件SYSWELD,采用有限元热弹塑性分析方法和Fortran语言对焊接热源进行二次开发,获得了所需要的热源,并通过实验验证了热源模型的准确性.在此基础之上,通过分析高速列车CRH380B侧墙焊接残余应力分布规律和焊接顺序对于侧墙焊接残余应力的影响,得到了侧墙焊接最优方案,为企业实际生产中的降低焊接残余应力方案选择提供了依据.     

破损船体梁残存强度的有限元计算模型研究

采用Abaqus软件建立多个非线性有限元计算模型,对完整和破损后的船体梁进行非线性有限元计算。通过与Smith方法的结果对比分析,确定船体梁残存强度非线性有限元计算模型和边界条件,并研究破口周围边界对残存强度的影响。     

基于波分析法油膜刚度对轴系扭转振动影响的研究

为确保带减速齿轮箱主推进系统的可靠性,文章对船舶轴系的扭转振动进行了研究。首先根据各组成部件的特点将轴系分解为连续和离散的两个子系统,分别利用波分析法和多自由度系统分析法列出连续子系统的波动形式及离散子系统的振动微分方程,同时考虑了减速齿轮箱油膜刚度的影响。然后根据两子系统连接处的动态平衡和连续条件,建立整个轴系在扭转振动模式下总运动方程,通过求解总方程得到系统的位移响应。该扭转振动分析被应用到某LNG船带减速齿轮箱的轴系振动计算中,通过考虑轴系减速齿轮箱啮合齿面间油膜刚度使轴系扭转振动模型更接近轴系实际运转工况。计算结果显示：随着减速齿轮箱啮合齿面间油膜刚度的增加,最大轴系扭转应力向低转速区域偏移。这对船舶轴系转速禁区的划分产生极大的影响。有助于防止因不良轴系振动计算引起轴系事故的发生。