Total dynamic response of a PSS vehicle negotiating asymmetric road excitations

A planar suspension system (PSS) is a novel automobile suspension system in which an individual spring–damper strut is implemented in both the vertical and longitudinal directions, respectively. The wheels in a vehicle with such a suspension system can move back and forth relative to the chassis. When a PSS vehicle experiences asymmetric road excitations, the relative longitudinal motion of wheels with respect to the chassis in two sides of the same axle are not identical, and thus the two wheels at one axle will not be aligned in the same axis. The total dynamic responses, including those of the bounce, pitch and the roll of the PSS vehicle, to the asymmetric road excitation may exhibit different characteristics from those of a conventional vehicle. This paper presents an investigation into the comprehensive dynamic behaviour of a vehicle with the PSS, in such a road condition, on both the straight and curved roads. The study was carried out using an 18 DOF full-car model incorporating a radial-spring tyre–ground contact model and a 2D tyre–ground dynamic friction model. Results demonstrate that the total dynamic behaviour of a PSS vehicle is generally comparable with that of the conventional vehicle, while PSS exhibits significant improvement in absorbing the impact forces along the longitudinal direction when compared to the conventional suspension system. The PSS vehicle is found to be more stable than the conventional vehicle in terms of the directional performance against the disturbance of the road potholes on a straight line manoeuvre, while exhibiting a very similar handling performance on a curved line.     

A novel fuzzy logic correctional algorithm for traction control systems on uneven low-friction road conditions

The traction control system (TCS) might prevent excessive skid of the driving wheels so as to enhance the driving performance and direction stability of the vehicle. But if driven on an uneven low-friction road, the vehicle body often vibrates severely due to the drastic fluctuations of driving wheels, and then the vehicle comfort might be reduced greatly. The vibrations could be hardly removed with traditional drive-slip control logic of the TCS. In this paper, a novel fuzzy logic controller has been brought forward, in which the vibration signals of the driving wheels are adopted as new controlled variables, and then the engine torque and the active brake pressure might be coordinately re-adjusted besides the basic logic of a traditional TCS. In the proposed controller, an adjustable engine torque and pressure compensation loop are adopted to constrain the drastic vehicle vibration. Thus, the wheel driving slips and the vibration degrees might be adjusted synchronously and effectively. The simulation results and the real vehicle tests validated that the proposed algorithm is effective and adaptable for a complicated uneven low-friction road.     

锚喷支护设计专家系统的研究

锚喷支护设计专家系统（ＰＴＥＳ）是在广泛收集国内外锚喷支护设计的理论知识和广大支护专家群体丰富设计经验的基础上，结合国家标准锚喷支护设计规范，应用专家系统技术研制而成的。它是一个以人－机对话为主，具有多模块、多功能的智能化程序设计软件。它能模仿人类专家的思维方式和思维过程，最终根据工程类型、地质条件、围岩类别、工程断面形状和尺寸等因素确定工程的支护形式和支护参数。     

铁路车站信号设备故障诊断专家系统的研究

针对我国铁路信号设备故障的特点,基于诊断和专家系统的理论与方法,对铁路车站信号设备故障诊断专家系统的原型开发结构进行设计分析.通过对铁路车站信号设备的常见故障进行具体分析,从构造知识库,到模型推理,为建立切实可行的专家系统进行详尽的阐述,为通过人工智能方法建立和开发我国铁路信号故障诊断专家系统提供重要依据.     

滨海相软基袋装砂井加固施工技术

黄万铁路通过滨海相软土地基段采用换填、砂垫层、土工格栅及袋装砂井加固处理,取得了良好的加固地基效果,介绍其施工方法、工艺及注意事项。     

港口AIS网络的构建

构建港口船舶自动识别系统通信(AIS)网络是港口现代化建设的重要方面,文章以宁波港为例,提出港口AIS网络的构建方案,对基站选址与港口信息管理系统融合问题做了重点分析。     

内外温差对明挖隧道主体结构内力的影响研究

明挖隧道内外温差会使其衬砌结构产生附加应力,严重时会使隧道轴线方向的衬砌产生环向裂缝。通过对温度进行现场监测,获得工程实际内外温差,对其规律进行简要分析并将其作为有限元计算的温度边界条件;采用ANSYS进行有限元计算,考虑明挖隧道主体结构修建完成和回填完成两个阶段,对隧道内部温度低于外部温度、隧道内部温度高于外部温度以及无温差3种工况进行分析,得出温差对隧道结构应力的影响规律。     

H型钢接触网支柱在风荷载作用下的疲劳性能分析

H型钢接触网支柱在高速铁路中得到广泛使用,直接影响铁路接触网系统安全。长期处于风荷载作用下,H型钢接触网支柱存在疲劳问题。通过建立数值计算模型,应用热点应力的表面外推法,对H型钢接触网支柱柱脚焊缝在风荷载作用下的疲劳性能进行分析。以兰新高铁H型钢接触网支柱为例,依据热点应力-寿命曲线,计算支柱焊缝的疲劳寿命。分析结果表明:其他条件不变的情况下,改变型钢规格和柱高,热点位置不发生变化;随着支柱高度增加,疲劳寿命降低21%左右;随着型钢截面的增大,疲劳寿命增加23%左右。     

北京地铁车站附属建筑的设置

以北京在建地铁4、5号线、10号线一期工程的规划设计、建设实践为基础,分析以往地铁车站附属建筑设置过程中容易忽视的几个细节问题,如车站出入口、通风亭、冷却塔与城市道路红线、建设用地及文物的关系,以及通风亭和冷却塔的建筑形式等。最后得出结论：地铁车站附属建筑设置应结合城市道路近、远期规划科学设置,满足城市道路交叉口渠化、人行道最小宽度要求。现状已实现规划的建设用地内尽量不安排车站附属建筑;位于城市待改造用地内,出入口、通风亭及部分通道应按临时建（构）筑物设计,待规划实施时,其改造方案可与建设项目统一设计;位于正在办理规划审批手续的建设用地内,车站附属建筑应与建设项目作一体化设计。旧城内车站附属建筑设计应做多方案比选,慎重抉择。环控专业应提早参与配合,设计前期应事先确定通风亭、冷却塔的建筑形式,以便预留合适的用地,做到及早控制。     

水火弯板数据库系统设计

本文简述水火弯板变形原理，以及船板局部变形和整体变形的测试方法。在分析实船板的水火成形数据库系统数据结构基础上，给出了系统模块的设计功能和系统运行环境。