浅埋顶管沉井周边土体的三维破坏形状及沉降研究

为研究顶管沉井及周边土体在顶进力作用下的形变范围与大小，以加固旋喷桩作为沉井周围加固体建立ABAQUS软件计算模型，并将模拟结果与工程实例、PLAXIS 3D软件所得结果进行对比分析。同时，采用广州地区花岗岩残积土进行室内沉井模型试验，并通过试验结果对数值模拟结论进行验证，得出结论如下： 1）在开挖基坑前达到设计强度的旋喷桩能有效减小基坑周边土体塌陷变形、坑底隆起。2）在施加工作顶推力下，前侧主动区首先出现贯通裂缝，竖向位移斜率增大出现明显拐点；继续增大顶推力，土体位移会急剧增大导致地表沉降严重。3）对于后背土体，在顶推力作用下，地表破裂线的切线角度从0°逐渐增大至45°+φ/2，导致破裂范围也不断扩大；达到45°+φ/2处后，继续施加顶推力会导致短轴方向破坏范围扩大的速度较长轴方向的速度更快；三维空间中被动区破坏土体在地表处产生形状为椭圆的破坏面，椭圆长轴方向为顶推轴线方向，被动破坏体呈现为牛角状椭圆楔体。     

中韩船舶油污损害赔偿制度的比较

韩国不论是从地理位置还是经济贸易往来,对于我国是很重要的邻国.由于海上运输的国际性,我国的船东有在该国卷入油污损害赔偿案件的可能,研究其油污损害赔偿制度能够更好的保护我国船东的权益,而且对于我国完善油污民事赔偿立法有一定的借鉴作用.本篇论文比较了中韩油污损害赔偿制度,并对完善我国油污损害赔偿制度提出几点建议.     

钩形外锁闭装置锁闭框组优化的探讨

钩形外锁闭装置在实践中逐步暴露出一些诸如转换不畅、卡阻,磨耗严重,适应尖轨窜动性不良等问题.为此研究探讨对既有的外锁闭装置锁闭框组（包括锁闭框、锁闭铁、耐磨板等）进行优化,提高道岔转换的可靠性.     

Robust traffic assignment model: Formulation,solution algorithms and empirical application

ABSTRACT

The deterministic traffic assignment problem based on Wardrop's first criterion of traffic network utilization has been widely studied in the literature. However, the assumption of deterministic travel times in these models is restrictive, given the large degree of uncertainty prevalent in urban transportation networks. In this context, this paper proposes a robust traffic assignment model that generalizes Wardrop's principle of traffic network equilibrium to networks with stochastic and correlated link travel times and incorporates the aversion of commuters to unreliable routes.

The user response to travel time uncertainty is modeled using the robust cost (RC) measure (defined as a weighted combination of the mean and standard deviation of path travel time) and the corresponding robust user equilibrium (UE) conditions are defined. The robust traffic assignment problem (RTAP) is subsequently formulated as a Variational Inequality problem. To solve the RTAP, a Gradient Projection algorithm is proposed, which involves solving a series of minimum RC path sub-problems that are theoretically and practically harder than deterministic shortest path problems. In addition, an origin-based heuristic is proposed to enhance computational performance on large networks. Numerical experiments examine the computational performance and convergence characteristics of the exact algorithm and establish the accuracy and efficiency of the origin-based heuristic on various real-world networks. Finally, the proposed RTA model is applied to the Chennai road network using empirical data, and its benefits as a normative benchmark are quantified through comparisons against the standard UE and System Optimum (SO) models.     

Travel time estimation oriented freeway sensor placement problem considering sensor failure

Optimal sensor placement on freeway corridor is of great interest to transportation authorities. However, current traffic sensors are easily subject to various failures. Therefore, it is necessary to incorporate sensor failure into the optimal sensor placement model. In this article, a two-stage stochastic model is proposed for the purpose of travel time estimation on freeway corridor. To balance the effectiveness and reliability, a stochastic conditional value at risk (CVaR) model is also proposed. Since both models are too complicated, a customized genetic algorithm is developed. Numerical experiments show that considering sensor failure makes a significant performance improvement in the sensor placement pattern. Sensitivity analysis is also applied to investigate the impact of a number of allowable sensors and different traffic sensor failure probability.     

汕头苏埃隧道方案设计关键技术研究

根据汕头苏埃隧道的建设条件,对工程方案设计中的几个技术难点进行研究,并提出解决方案。通过采用"多级分流"理念,实现隧道与北岸4条城市主干道的交通衔接;选择"抛石+排水板"方案解决海域深厚淤泥地层中的围堰设计;8度高烈度震区选择合理的抗震减震措施解决隧道结构抗震;采取双道密封垫和加大密封垫断面的防水设计,满足地震时管片接缝张开量大的防水要求;针对复杂地层,对盾构选型和配置提出建议;对海底凸起进入隧道内的硬岩进行爆破预处理,以降低盾构施工风险。     

小直径盾构施工中管片纵向应力监测研究

为了探索小直径盾构法隧道在施工过程中管片纵向应力的变化规律,对北京槐房再生水厂污水隧道管片纵向应力进行了现场监测:将第976环、第1 054环管片分别设为第1和第2监测断面,2监测断面各预埋5个纵向应力计,各监测断面从本监测断面管片安装后即开始监测,当盾构掘进至第1 129环时停止监测。研究表明:1)在管片离开盾尾50环后,其纵向应力波动值小于管片拼装期间应力值的5%。2)在盾构掘进期间,管片距离盾构越远,其纵向压应力值越小。3)在管片拼装期间,管片距离盾构越远,其纵向压应力经历了先增大后减小的过程。4)管片距离盾构108环后,该管片纵向压应力趋近于0.2~0.3 MPa。5)随着盾构推进,管片纵向应力经历了4个阶段的变化过程,即周期性剧烈波动阶段—动态稳定阶段—逐渐衰减阶段—趋于稳定阶段。     

薄基岩顶板隧道爆破施工围岩稳定性分析

为更有效地进行薄基岩顶板条件下隧道施工安全控制,以某高速公路隧道为工程背景,运用数值模拟的方法,分别研究不同顶板厚度下隧道爆破施工引起的围岩振速分布特征及其对围岩的损伤情况,并进行围岩稳定性分析。结果表明:1)当顶板厚度在5 m及以上时,围岩是稳定的;2)当顶板厚度为3 m时,最危险横断面上基岩顶板内开始产生严重的拉伸裂缝及一些径向裂缝,将形成超挖;3)当顶板厚度≤2 m时,径向裂缝贯穿顶板岩体,围岩稳定性较差,在掌子面后1 m内可能发生塌落、掉块等事故。     

极高地应力软岩隧道超前导洞应力释放及多层支护变形控制技术

为了解决极高地应力软岩隧道大变形控制难题,以兰渝铁路木寨岭隧道岭脊核心段施工为例,通过现场试验和数据分析,得到如下主要结论:1)提出了"先放后抗,抗放结合,锚固加强"的变形控制理念;2)得出了该隧道岭脊核心段"超前导洞应力释放+圆形4层支护结构+径向注浆+长锚杆+长锚索"综合变形控制方案;3)超前导洞应力释放效果明显,正洞累计变形减小幅度约为34%;4)得到了圆形多层支护结构变形规律;5)累计变形均控制在设计预留变形量内,保证了该隧道岭脊核心段大变形控制效果。     

The Kalker book of tables for non-Hertzian contact of wheel and rail

A new regularisation of non-elliptical contact patches has been introduced, which enables building the look-up table called by us the Kalker book of tables for non-Hertzian contact (KBTNH), which is a fast creep force generator that can be used by multibody dynamics system simulation programs. The non-elliptical contact patch is regularised by a simple double-elliptical contact region (SDEC). The SDEC region is especially suitable for regularisation of contact patches obtained with approximate non-Hertzian methods for solving the normal contact problem of wheel and rail. The new regularisation is suitable for wheels and rails with any profiles, including worn profiles.

The paper describes the new procedure of regularisation of the non-elliptical contact patch, the structure of the Kalker book of tables, and parameterisation of the independent variables of the tables and creep forces.

A moderate volume Kalker book of tables for SDEC region suitable for simulation of modern running gears has been computed in co-simulation of Matlab and program CONTACT.

To access the creep forces of the Kalker book of tables, the linear interpolation has been applied.

The creep forces obtained from KBTNH have been compared to those obtained by program CONTACT and FASTSIM algorithm. FASTSIM has been applied on both the contact ellipse and the SDEC contact patch. The comparison shows that KBTNH is in good agreement with CONTACT for a wide range of creepage condition and shapes of the contact patch, whereas the use of FASTSIM on the elliptical patch and SDEC may lead to significant deviations from the reference CONTACT solutions.

The computational cost of calling creep forces from KBTNH has been estimated by comparing CPU time of FASTSIM and KBTNH. The KBTNH is 7.8–51 times faster than FASTSIM working on 36–256 discretisation elements, respectively.

In the example of application, the KBTNH has been applied for curving simulations and results compared with those obtained with the creep force generator employing the elliptical regularisation. The results significantly differ, especially in predicted creepages, because the elliptical regularisation neglects generation of the longitudinal creep force by spin creepage.